Search Documents

By J. C. Wilhoit, E. M. Galle

A three-dimensional photoelastic study was made to determine the stress state around the wall and bottom of a wellbore due to fluid pressure within the wellbore and unequal principal geostatic stresses. Models simulating the wellbore were made from a phthalic anhydride-cured epoxy resin. The frozen stress technique of three-dimensional photoelastic-ity was used to determine the stresses within the model. Two separate problems were solved: (1) hydrostatic pressure on all sides of the model with the exception of the inside of the hole, and (2) uniaxial compression perpendicular to the center line of the hole. The results are presented in the form of contour curves for each stress component. The curves cover a region which extends several hole radii from the bottom and wall of the hole. By proper use of these results, the state of stress may be calculated for any point on the wall or bottom of the hole, as well as for any point within the material that surrounds the hole. A systematic method is given for calculating these stress components for any combination of fluid pressure within the wellbore and system of unequal principal geostatic stresses, provided one of the principal geostatic stresses is parallel with the wellbore. The results show that stresses around the wall and bottom of a wellbore, induced by an uneyual system of principal geostatic stresses, are appreciably different from those induced by geostatic stresses that are hydrostatic. For uneyual principal geostatic stresses, the experimentally determined stresses on the wall of the hole several radii from the bottom are in good agreement with the stresses calculated by elastic theory. INTRODUCTION Interest in the problem of determining the stresses around and near the bottom of a wellbore, due to geostatic loading and fluid pressure within the wellbore, originated in the petroleum industry. The stresses on the wall of the wellbore are of interest due to their relation to lost circulation during drilling, the fracturing of formations during squeeze cementing and hydraulic fracturing of producing formations. The stresses on the bottom of the hole are of interest to the drilling segment of the industry because to produce a hole in the earth it is necessary to remove material from the bottom of the hole. This removal of material is produced by structural failure of the rock, whatever the criterion for failure may be. Cunningham and Eeninkl have shown that for certain conditions the effect on drilling rate of the bottom-hole stresses caused by a hydrostatic overburden pressure is small compared to other effects. This question, however, needs further experimental and analytical investigation. Much information concerning the stresses on the walls of wellbores has been published considering both equal and unequal principal geostatic stresses. The problem of determining the stresses around the bottom of the wellbore is considerably more complicated. However, previous investigators have obtained numerical and experimental solutions to the problem for equal principal geostatic stresses. whitworth2 and woods3 have obtained numerical solutions. word415 obtained a three-dimensional photoelastic solution, Durelli and Deily 6 obtained surface stresses only by photoelastic means, and Cheatham and Wilhoit7 determined the stresses around the bottom of a short cylindrical cavity. While Miles and McGuire, Harrison and Kieschnick and Hubbert and Willis 10 obtained the stresses on the wall of a wellbore for unequal principal geostatic stresses, they did not concern themselves with the stresses near the bottom of the hole. The estimates made by Hubbert and Willis of the differences between the principal geostatic stresses indicate that, to obtain a satisfactory solution for the stresses around the bottom of a wellbore, unequal principal geostatic stresses should be considered. This work is directed toward obtaining such a solution. The materials in the earth's crust are nonhomo-geneous, permeable and anisotropic. Previous

By W. R. Strickler, P. Hazebroek, M. Prats

The pressure and production behavior of a homogeneous cylindrical reservoir producing a single fluid through a centrally located vertical fracture of limited lateral extent was determined by using mathematical methods to solve the appropriate differential equation. It is assumed that there is no pressure drop within the fracture — that is, that the fracture capacity is infinite. It was found that the production-rate decline of such a reservoir is constant (except for very early times) when the flowing bottom-hole pressure remains constant. The production-rate decline increases as the fracture length increases. Thus, the lateral extent of fractures can be determined from the production-rate declines before and after fracturing or from the decline rate after fracturing when the properties of the formation and fluids are known. The production behavior over most of the productive life of such a fractured reservoir can be represented by an equivalent radial-flow reservoir of equal volume. The effective well radius of this equivalent reservoir is equal to one-fourth the total fracture length (within 7 per cent); the outer radius of this equivalent reservoir is very nearly equal (within 3.5 per cent) to that of the drainage radius of the fractured well. The effective well radius of a reservoir producing at semisteady state is also very nearly equal to one-fourth the total fracture length. It thus appears that the behavior of vertically fractured reservoirs can be interpreted in terms of simple radial-flow reservoirs of large wellbore. INTRODUCTION An earlier report1 has considered the effect of a vertical fracture on a reservoir producing an incompressible fluid. That investigation of the fractured reservoir producing an incompressible fluid was started because of its simplicity. Thus, pertinent behavior of fractured reservoirs was obtained at an early date, while experience was being gained of value in the solution of more complicated fracture problems. One of these more complicated problems, and the one discussed in this report, considers the effect of a compressible fluid (instead of incompressible fluids) on the production behavior of a fractured reservoir. In the incompressible-fluid work mentioned, it was shown that the production rate after fracturing could be described exactly by an effective well radius equal to one-fourth the fracture length whenever the pressure drop in the fracture was negligible. Because of the simplification in interpretation, it is a matter of much interest to determine whether the production behavior of reservoirs producing a compressible liquid could be described in terms of an effective well radius which remains essentially constant over the producing life of the field. The details of the mathematical investigation are given in the Appendixes. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable circular cylindrical outer boundary of radius re. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir just described. When gravity effects are neglected, the flow behavior in the reservoir is independent of the vertical position in the oil sand. Thus, the flow behavior in the fractured reservoir is described by the two-dimensional flow behavior in a horizontal cross-section of the reservoir, such as the one shown in Fig. 2. Production is due to the expan-

By R. H. Jacoby, V. J. Berry

When dry gas is injected into a reservoir containing a volatile crude oil, a significant amount of the reservoir liquid phase may become vaporized. The resultant rich gas phase, when subsequently produced, con-tributes to tank oil production. This contribution assumes greater importance, the more volatile the oil in-olved. Oil recovery may be sub-stantially greater than that predicted by conventional frontal-drive methods, which do not consider the vaporization equilibrium between the reservoir oil phase and the injected gas. A calculation method has been (developed to account for vaporiza-. tion of the reservoir liquid phase during gas-injectiorz operations, and for the tank oil production which results from this factor. Recovery performance calculations are presented for a reservoir containing a highly volatile oil. Tank oil recovery is calculated to be about twice that predicted by the use of the conven-rional frontal-drive equations. In contrastto usual pressure maintenance performance results, in which the gas-oil ratio rises at an increasing rate after gas breakthrough, the pre-dicated gas-oil ratio rises rapidly to about 12,000 scf/bhl and then rises much less rapidly. During gas inje-tion, most of the reservoir liquid phase contacted is evaporated by the dry injection gar. The gas-oil ratio during this period is dependent upon reservoir pressure. The higher the operating pressure, the lower the gas-oil ratio. The predicted behavior i., in accordance with laboratory PVT tests made to .simulate the vaporization behavior. In addition to recovery performance predictions, results of the calculation procedure include complete wellstrearn composition data of value in the design of gasoline plant facilities often used in con-rrction with gas-injection operations. INTRODUCTION In the cycling of gas-condensate reservoirs, dry gas is injected to maintain reservoir pressure during wet gas production and to thereby eliminate or reduce ultimate loss of liquids due to retrograde condensation within the reservoir. Gas injected into crude oil reservoirs has a dual function. It displaces oil to the producing wells and at the same time serves to partially or fully maintain reservoir pressure. Oil shrinkage which would occur upon pressure reduction is thereby minimized or eliminated. Accepted calculation methods are available'= for predicting recovery performance of either gas-condensate reservoirs or crude oil reservoirs which are being subjected to gas injection. In gas-condensate reservoirs, any retrograde liquid formed does not flow, and it is necessary to account only for the vaporization equilibrium between this liquid and the injected gas. Conversely, in normal crude oil reservoirs, both the oil and gas phases flow, but it has not been considered necessary to account for any vaporization of the reservoir liquid which might occur upon contact with the dry injection gas. Recently, high shrinkage reservoir fluids known as "volatile oils" have been found in increasing amounts. These oils are characterized by tank oil gravities above 4.5" API, solution gas-oil ratios above 1,000 scf/bbl, and reservoir volume factors above two. Special techniques have been devised for predicting depletion performance of reservoirs containing such oils.74.5.1; One of the characteristics of reservoirs producing volatile oils is that the reservoir gas phase carries a significant amount of oil which is recoverable as stock-tank liquid. This unusual vaporization be-havior implies that an appreciable amount of reservoir liquid would be vaporized upon contact of the oil with dry injection gas. In a gas-injection operation, tank oil recovery would he obtained not only through frontal displacement of the reservoir liquid by the injected gas, but also through production of the rich gas phase. This means that not only are improved methods needed to predict recovery of such oils from reservoirs undergoing gas injection, but it would also be expected that high oil recoveries might be obtained by such operations. When relatively dry gas is injected in to a volatile oil reservoir, phase equilibrium between the injected gas and the reservoir oil will tend to bc established. Initially the most volatile components, such as propane, the butanes and the pentanes, will account for most of the material transferred from the oil phase to the gas phase. As the partially stripped oil phase is contacted with additional dry injection gas, the heavier intermediate components, such as the hexanes, the heptanes and the octanes, will gradually transfer to the gas phase in increasing amounts. This is because the supply of lighter components in the oil phase dwindles due to the stripping action of the injected gas. This stripping action will usually continue to be effective down

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.', n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " '.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.',' Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a'=-n;s/= nD,(qo);"; and b' = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

By D. R. Babich, E. R. Bauer

Noise-induced hearing loss (NIHL) in mine workers, especially underground coal miners, continues to be a problem in the mining industry. The recently enacted MSHA noise standard, Part 62 – Occupational Noise Exposure (Federal Register, 1999), is aimed at reducing NIHL in the mining industry. The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in various aspects of coal mining including surface mining, coal preparation plants and underground mining. In underground bituminous coal mining, noise surveys, consisting of full-shift worker noise exposure, time-motion studies and equipment noise profiling, have been completed on longwall and continuous miner sections in six underground coal mines. The studies revealed widely varying shift-to-shift worker exposures, with workers in certain occupations routinely exposed to potentially hazardous levels of noise. A summary of these studies is reported, including worker dose, source/dose relationships and equipment noise profiles.

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By W. H. Bassett, C. Davis

Although brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent, copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,' the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry' extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.' These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

By G. M. Webster, G. E. Dawsongrove

The use of percussion-type side-wall cores as an aid in detection and evaluation of hydrocarbon shows and in examination of rock properties has become increasingly popular in recent years. Sidewall coring has an advantage over normal bottom-hole coring methods in that the zones may be surveyed with the electric log prior to selection of sample depths. This allows an efficient sampling of all zones of interest, a procedure not possible with bottom-hole coring techniques unless the costly procedure of continuous coring is utilized. Percussion sidewall coring presently provides the most rapid and lowest cost method of obtaining sidewall cores. It has been recognized for some time that certain discrepancies exist between core analysis data obtained from percussion cores and data obtained from other types of core Samples. This paper presents existing field and laboratory data that were available to the authors. Several examples of comparative core analysis data obtained from various fields are presented along with photomicrographs of thin sections of conventional and percussion cores. The results of this investigation are presented to throw more light on the possible disturbed condition of percussion sidewall cores. SAMPLE DISTURBANCE AND FRACTURING The principal cause of discrepancy between conventional core analysis data and percussion sidewall core analysis data is believed to be the shattering and re-adjustment of the grains due to the large impact shearing forces produced by mechanics of percussion coring. Figs. 1 through 5 are photomicrographs of thin section slides of formation samples obtained by means of diamond cores, conventional cores, and percussion sidewall cores. Figs. 1 and 2 show samples of the

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By Frederic E. Carter

The gold, silver, copper alloys have been the subject of several fairly complete investigations by Janecke, Sterner-Rainer&apos; and others, and indeed it would seem as if almost too much labor had been expended on them when one thinks of the numerous other ternary alloys calling for more light; however, the combinations of the three metals are actually so widely used in jewelry that they merit perhaps the work done on them. There are a few properties of importance and interest not treated by the authors mentioned which the writer investigated some little time ago, and therefore he has ventured to put on record the results of some of his tests made at that time. He has chosen, as being the two series of most importance to the jeweler, only the 14 and 18-kt. golds, so the subjcct is by no means so inclusive as that previously treated. As statecl, this paper is merely a record of tests made in a practical manner on two itucbful series of alloys, and is not at all a critical study of their properties. 14-Karat Alloys These alloys are important because they arc the most generally II,<(S(I in 14-kt, jewelry; by changing thc proportions of silvcbr and copper Iliero are obtained all shades of color from the green of the alloy contiainng gold and silver but no copper, to the red of the alloy containing gold ;,, copper but no silver. Many 14-kt. gold alloys are made with the sdditjon of zinc to the three metals mentioned here; the added lnetnl does not appreciably alter the color of the alloy nor has it, in general, much effect on the working properties; it may, however, prove useful as ynrt of thc zinc added may act as a deoxidizer and render the alloy free of ga,s. 11, iy not a necessary addition because with proper precautiolls :111 I lie 14-At. gold alloys containing only silver and copper in :tcltlitiotl to the gold ran be made free of gas and capable of being cold rolled without craci The alloys in which approximately equal quuntiticrs of silver ami

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far