Search Documents

By Richard J. Mainiero, Harry C. Verakis

The Bureau of Mines has conducted research to determine whether the total elapsed delay time for blasting bituminous coal in underground mines could be safely expanded beyond the present 500-ms limitation without igniting a methane or methane-coal dust atmosphere. The results indicated that the increase of total delay from 500 to 1,000 ms had no detectable effect on safety relative to incendivity as long as permissible practices were observed in all other aspects. Research was also conducted to evaluate the safety of 18-in hole spacing for delay blasting in coal relative to misfires. For a variety of permissible explosives, misfires were observed for about 50 pct of the holes at 18-in spacing. Based on this observation, the Bureau has recommended that the new regulations prohibit hole spacings of less than 24 inches in underground coal mines. Misfires were also observed for 24-in spacing, but the number of misfires and test shots was too small to sup- port any firm conclusions.

By Michael Feroz

Severe drought in the Colorado River Basin over the past 10 years has caused water levels to drop in Lake Mead by more than 113 feet. The current lake level is at elevation 1,112 feet mean sea level (msl). Lake Mead is the primary source of water supply for greater Las Vegas. Water for Las Vegas from Lake Mead is accessed through two existing submerged intake shaft and tunnel systems. If the water levels continue to drop in the lake, the Intake No. 1 will become inoperable below water level elevation of 1,050 feet msl. To sustain the current levels of water delivery to all member agen-cies in the southern Nevada region, the Southern Nevada Water Authority (SNWA) has decided to construct a third intake at a deeper depth in the lake to ensure better quality water and enhanced reliability.

The Annual General Meeting of the Branch was held in the Witbank Golf Club on Thursday, 28th August, 1969 at 5.00 p.m. Mr C. G. Sowry (Chairman) was in the Chair. There were also present: Ten Members: Messrs J. Meintjes (Vice-Chairman), J. E. van Aswegen, A. C. Hofmeyr, I. Botha, B. F. v. d. Merwe, C. H. Coxon, R. Canny, R. C. J. Goode, A. Bain, G. E. Carlyon. Six Associate Members: Messrs B. T. Hosking, R. E. Powell, W. Weber, T. Bulloch, E. J. Jackson, P. J. Muller. Fourteen Visitors. Total Present: 31. The Chairman declared the meeting open and extended a welcome to all visitors including Mr R. C. J. Goode, President of the Institute. MINUTES OF PREVIOUS GENERAL MEETING The Minutes of the General Meeting held on the 26th June, 1969, were read and adopted. CHAIRMAN'S REPORT The Chairman presented a report outlining the activities of the Branch during the past year. Membership of the local Branch had increased from 80 to 99 during the year. DECLARATIONOF OFFICEBEARERS The Chairman announced that owing to his transfer out of the Witbank area, he was unable to accept the nomination as Chairman for a further year of office. The outgoing committee had elected Mr J. Meintjes Chairman and Mr A. Bain Vice-Chairman for the ensuing year. Mr J. Meintjes then took the chair. Mr J. Meintjes thanked Mr C. G. Sowry for his successful steering of the Branch during its period of inauguration. ELECTION OF COMMITTEE MEMBERS The Chairman then read the Scrutineers' Report and declared the following eight members elected as Committee Members for the 1969-1970 year: Messrs I. Botha, A. W. Brereton, G. E. Carlyon, B. T. Hosking, E. J. Jackson, B. D. McNeice, P. J. Muller, B. F. van der Merwe. TALK The Chairman then called upon Mr A. Bain to present his talk and film show on 'Impressions of the mining and metallurgy congress tour to Australasia'. CLOSURE After thanking the speaker for an interesting talk, the Chairman declared the Meeting closed at 8.40 p.m.

By Peter Swanson, John Rettkowski

As part of a research program to reduce injuries and fatalities in the U.S. mining workforce, NIOSH is investigating the potential use of noncontact vibration measurements to identify hazardous ground fall conditions. In the present study, the effectiveness of remote vibration sources in exciting resonant responses in damaged structures is examined. Initial experiments were performed on a damaged concrete slab in a controlled environment. Vibration response was measured with a laser Doppler vibrometer using both single-point and two-dimensional array recordings. Excitation sources included direct mechanical impacts to remote portions of the slab and a remotely located industrial demolition hammer. Surficial damage was effectively delineated with both sources through visualization of vibration response in spectral bands selected to discriminate wave propagation from large-scale slab resonance effects.

By Mahmood Alemrajabi

When LKAB processes their iron ores in northern Sweden, they generate apatite as a by-product. The apatite has been recovered by flotation and the concentrate contains about 0.4 wt% rare earth elements (REE). Both phosphate rock and REE are listed as critical raw materials for the European union. In the present study, the recovery of REE within the nitrophosphate process of fertilizer production has been studied. In the first stage, the REE are precipitated and isolated as a phosphate concentrate. For further purification and individual separation of REE by solvent extraction, removal of phosphorous from the concentrate to enhance the dissolution of REE in mild acidic solutions is essential. In this study, thermal treatment of the concentrate with sodium hydroxide at elevated temperatures followed by water leaching has been studied in order to separate the phosphorous and thereby facilitate dissolution of the REE. The results show that 95% of total phosphorous initially present in the REE phosphate concentrate is removed after thermal treatment with NaOH 1:1 mass ratio, at 400 °C.

By H. L. Stone, A. O. Garder

A numerical method of solving the partial differential equations which describe the one-dimensional displacement of oil by gas has been presented. Possible extension of the method to treat multidimensional flow is discussed, and the limitations of this extension are indicated. Using this method, it is possible to allow for the existence of a gas cap, the presence of any number of gas-injection or oil-production wells and the evolution of dissolved gas from the oil. It is also possible to allow for variation in the cross-sectional area, elevation, porosity and permeability of the reservoir. The influence of relative permeability and the force of gravity in the direction of flow upon the displacement is considered. The influence of capillary pressure upon the flow and the effect of gravity in the direction perpendicular to flow are neglected. The physical properties 01 the fluids are considered to be Junctions of pressure only, and equilibrium between contiguous phases is assumed. The numerical calculations can be readily carried out by the use of a digital computer. Several example analyses have been performed using the IBM 704 computer, and about one-third of an hour of computing time was required per case. Reservoir behavior predicted by use of this numerical method was compared to data obtained by other methods for three cases — complete pressure maintenance, dissolved-gas drive and gas-cap drive. The independent solutions to these problems were obtained by analytical solution, laboratory experiment and field data, respectively. Agreement of the numerical solution with data from these sources was good; this agreement establishes the convergence and accuracy of the numerical method. INTRODUCTION Most petroleum reservoirs can be produced by any one of several alternative programs. When a reservoir is produced by primary methods, production economics can be influenced by controlling the number and location of wells and the flow rate of each well. An even greater influence may be achieved by augmenting the recovery of oil obtainable by primary methods. This can be accomplished by injection of fluids such as water, natural or enriched gas or a bank of light liquid hydrocarbons. Selection of the most desirable operation requires a means of predicting the reservoir behavior which will result from each of the several alternative programs. The purpose of this paper is to present a mathematical method for predicting the behavior of reservoirs produced by gas-cap drive, dissolved-gas drive or pressure maintenance by gas injection. The method described herein takes cognizance of phase changes caused by a decline or an increase (due to gas injection) in reservoir pressure, of the presence of a gas cap and of the effect of gravity on the flow of gas and oil. Relative permeability relationships are used to define the flow properties of the rock. Allowance is made for variation in cross-sectional area, elevation, permeability and porosity of the reservoir. Both the influence of capillary pressure upon the flow and pressure gradients in the gas cap are neglected. Whenever a liquid phase and a gas phase are in contact, they are assumed to be in equilibrium. The physical properties of the fluids are considered to be functions of pressure only. Therefore, if the method is to be used to predict the effects of a gas-injection program, mixtures of the injected gas and formation crude should-have the same physical properties as mixtures of formation gas and crude. The equations to be presented in this paper apply only to a one-dimensional case; therefore, they neglect the influence of gravity in the direction transverse to the flow. As is well known, this gravitational influence may lead to overriding of oil by gas. Consequently, this procedure as presented is most applicable to long, thin reservoirs for which gravity overriding is not important. On the other hand, the equations presented can be generalized to treat multidimensional flow and, hence, to consider gravity overriding, if desired. A word of caution on two points is advisable here, however. First, the authors have not demonstrated the accuracy of the numerical technique for multidimensional flow. Second, and more important, capillary pressure will often be of importance in multidimensional problems. Obviously, in such cases a generalization of the

By Fred C. Turin, Kim M. Cornelius

Work in underground coal mines is repetitive and physically demanding. Workers commonly report a wide range of aches and pains. Management at one mine was concerned about increased reporting of aches and pains by roof bolting machine operators. An analysis of roof bolting tasks was conducted at this mine to identify early warning signs of cumulative trauma. Health and safety risk factors were identified and recommendations to reduce cumulative trauma exposure were provided. Recommendations addressed job procedures, equipment design, and worker awareness of risk factors.

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-

By F. W. Schremp, J. W. Chittum, T. S. Arczynski

This paper describes a laboratory study of causes of external casing corrosion and the test work that led to the use of oxygen scavengers to prevent this attack. External casing failures are classified as water-line, casing-casing, collar and body failures. A corrosion mechanism based on principles of differential oxygen availability is developed that is consistent with facts known about each kind of failure. The field use of oxygen scavengers is depicted as a direct result of the laboratory study. A part of the paper is devoted to reporting on the field use of hydra-zine to control external casing corrosion. Results of field measurements made over a period of several years are presented as evidence of the efectiveness of the hydrazine treatment. The first conclusion reached is that the use of hydrazine materially reduces the cathodic protection requirements for treated wells. This result is interpreted to mean that a reduction is taking place in the amount of corrosion on the casing. Results indicate also that hydrazine shows its greatest usefulness within the first 12 to 18 months after a well is completed when pitting corrosion is likely to be most active. INTRODUCTION According to surveys sponsored by the National Association of Corrosion Engineers,' the cost of repairing casing leaks caused by external corrosion may exceed $4 million per year. In addition, well damage and lost production resulting from casing leaks probably costs the petroleum industry an additional $5 to $6 million per year. Concern about the cost of external casing corrosion led to an extensive laboratory study of factors causing this external corrosion and to the development of a new approach to its prevention. This paper presents a discussion of various causes of external casing corrosion, details of laboratory studies and the results of the field use of an oxygen scavenger in well cementing fluids to prevent the external corrosion of oil-string casing. Measurements on test wells over a period of several years show that cathodic-protection current requirements are greatly reduced when hydrazine is used in cementing mud. Reduction of current requirements can be interpreted to mean that removal of oxygen by hydrazine has greatly suppressed corrosion cells on the external surface of the casing and thereby, has reduced corrosion. To date, hydrazine has been used by the Standard Oil Co. of California in more than 200 well completions. KINDS OF CASING FAILURES A survey of a large number of casing leaks disclosed four types of external casing failures — water-line, casing-casing, collar and body failures. These types are identified largely by their location on the casing. Water-line failures are found just below the surface of water or mud in the casing annulus. Casing-casing failures occur on the oil string just below the shoe of the surface string. Collar failures are found in the threaded ends of casing joints where they are screwed into casing collars. Body failures may occur at any point on the body of a casing joint. Ex- amples of each kind of failure have some of the general characteristics that are shown in Fig. 1. Water-line failures usually result in the circumferential severance of an oil-string casing. The corrosive action causing a water-line failure usually is sharply defined and is limited to a short length of the casing. Casing-casing failures usually are accompanied by pitting corrosion distributed around the oil-string casing for distances up to 100-ft below the shoe of the surface string. Casing-casing failures may also sever the casing. Collar failures seem to start on the first thread at the bottom of recesses between collar and casing joint. Corrosion proceeds across the threads by what appears to be a normal pitting mechanism. Both casing and collar are severely attacked. Body failures are the result of highly localized pitting at any point on a casing wall. Besides the pit that perforates a casing, a large number of other pits usually are found along one side of the casing joint. The pits occasionally are filled with corrosion products consisting largely of oxides and sulfides.' Frequently, the mill scale is largely intact on the rest of the casing. Examination of a casing failure does not always reveal the cause of the failure. Frequently, the necessary details are destroyed when the failure occurs. For example, formation water flowing through a perforation at high velocity may enlarge the hole and destroy any remaining evidence of the cause of the failure. One way to obtain undistorted information about a failure is to study the nature of other pits on the casing in the vicinity of the failure. A study of such pits frequently suggests that they are characteristic of an attack resulting from the differential availability of molecular oxygen.

This pamphlet and the enclosed video describe a safe, effective and economical method for removing dust from work clothes. Background Information Dusty work clothes can increase a worker’s exposure to respirable dust. Respirable dust is usually considered to be particles having an aerodynamic diameter of 10 microns or less and able to enter and deposit in the gas-exchange region of the human lung. A former U.S. Bureau of Mines report documented a 10-fold increase in worker dust exposure on a number of separate occasions from dusty work clothes.* It was found that once clothes become contaminated, they are a continual dust source until cleaned. The only MSHA approved method to clean work clothes requires a HEPA-filter vacuuming system which is very time consuming and difficult to perform effectively. Therefore, most workers use a single air hose (not MSHA approved) which can elevate dust levels for the worker, co-workers, and the work environment. A substantial amount of engineering technology has been developed that, when applied, can significantly lower respirable dust exposures of workers at mineral processing plants. But even with these improvements, some workers continue to exceed their permissible exposure limit. Elevated exposures increase the potential for developing debilitating or fatal lung diseases. ?e clothes cleaning method described within is an example of a continuing effort to reduce the potential for developing these lung diseases. Information about engineering research by the former U.S. Bureau of Mines and NIOSH can be found online at www.cdc.gov/niosh. ?is website can also be used for obtaining NIOSH information about health hazards associated with crystalline silica.

By Aram Grigoryan

This paper addresses the challenges of designing the underpinning of major sub-way station with 4 operating tracks. No. 7 subway extension crosses under the existing 42nd street subway station on the 8th Avenue line. Understanding the history of the original construction, of the current structures and their condition were instrumental in developing a feasible underpinning design that is integrated with the design of the new tunnels. The existing 8th Avenue subway station has a lower abandoned level. Several alignments and corresponding underpinning schemes were studied. The design allows new tunnel construction under the station without interruption of station operations.

By M. K. Larson, B. G. White

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the causes and mechanisms of roof failure in underground mines. It is expected that a better understanding of these causes and mechanisms will lead to better layout and support designs that will help prevent accidents and fatalities associated with fall of ground. Two numerical experiments were conducted by NIOSH researchers using the Fast Lagrangian Analysis of Continua (FLAC) computer modeling program with a strain-softening continuum to simulate fracture zones. Two models, one of a round hole in a plate and one of a rectangular opening, were constructed and boundary conditions were applied to simulate far-field shear. The Particle Flow Code in Two Dimensions (PFC2D) computer program was used to look at the effects of far-field shear in generating fractures around an underground opening, but these models are preliminary until boundary conditions, strengths, and stiffnesses are matched to the FLAC models. Results showed that shear zones propagated from the opposite corners of openings in directions that appeared to be determined by opening shape and far-field stress. Tensile failures also formed and extended away from these shear zones. The consistent direction of shear deformation with respect to far-field shear provides a plausible explanation for preferred directions of shear as seen in geologic environments.

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.

By P. Tim Johnson

Relentless increases in demand for nickel and vanadium for uses such as steelmaking, catalysts and battery materials, plus the growing financial and environmental costs of their primary extraction, have led to much interest in potential secondary sources of these metals. The presence of such metals in heavy fuel oils, bitumen and related materials offers both opportunities and challenges for potential extraction methods, especially with the growing production and importance of metal-rich fossil fuels around the world. For several decades, Tetronics’ DC plasma smelting technology has been used for the recovery of metals such as nickel and chromium from stainless steel melt dusts and other wastes in compact, environmentally-friendly and efficient plants. This paper explores the suitability of DC plasma smelting as part of a wider flowsheet with feed preparation and aluminothermic reduction techniques for smaller-scale extraction operations based on this important niche secondary source of these key metals.

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Zhi-xiang Cui

Dongying Fangyuan Nonferrous Metals Co., Ltd. has developed a new technology to produce anode copper from concentrates through only two furnaces. This new technology is called the Two-Step Copper Smelting Process. This paper presents the commercial application of the Two-Step Copper Smelting Process and its operating conditions. The key features of the Fangyuan Two-Step Process are as follows: (1) feed materials, including concentrates and flux, are mixed without pretreatment and fed into the Submerged Lance Smelting (SLS) furnace; (2) high grade white metal (WM) produced by the SLS furnace is transferred via WM conduit into one of the two Submerged Lance Converting and Refining (SLCR) furnaces; and (3) the two SLCR furnaces blow alternatively to maintain continuous operation of the whole production chain. The new smelter started operation in October 2015 with a processing design capacity of 1.75 Mt/year of mixed feed and has been operating for over 30 months.

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera. The burning process of the aluminized emulsion explosive has been modelled with the ignition and growth (I&G) flow model in the LS-DYNA code. A routine based on the optimization program LS-OPT code was developed to identify the parameters in the burning rate function with the detonation velocities and the front curvature radii from two tests. A Perl code was implemented in the routine and was used to calculate the VoD, fit the detonation front and obtain the detonation front curvature radii. The calibrated parameters were used to predict the VoDs and the detonation front curvature radii for the rest cases. The results indicate that both the VoDs and the detonation front curvature radii from the numerical modelling are in good agreement with the experimental results. The numerical results also indicate that the variety of the burn fraction and the peak pressure with the change of charge diameters is reasonable with the calibrated parameters.

By F. G. Miller, R. C. McFarlane, T. D. Mueller

During the process of gas storage in pressure-depleted oil reservoirs, it has been observed that in some instances additional liquid oil is recovered and that the composition of the storage gas is materially altered. A mathematical study was made of the dynamic behavior of such a depleted oil reservoir undergoing gas injection. The important variable considered in this study, not included in previously published work, was that of compositional effects on the phase behavior of two-phase flow. Pressure, saturation and component composition profiles were developed for a linear, horizontal and homogeneous porous medium containing oil and gas but undergoing dry gas injection. Special new techniques were developed to overcome the problems of numerical smoothing which arise in the solution of the equations representing such systems. The method of solution includes the development of partial differential equations describing the behavior of the system, representing these equations by finite difference approximations, making certain simplifying assumptions and, finally, applying methods of numerical analysis with the aid of a high-speed digital computer. In an example calculation, results using the mathematical model are compared with field observations made on a gas storage project in Clay County, Tex. This field project involved a depleted oil reservoir used 'for gas storage and gas cycling purposes. As a result of these processes, the reservoir yielded substantial amounts of secondary oil, both in the form of stock tank oil and as vaporized products in the produced gas. The methods derived in this study may be applied to a variety of oil reservoir problems which are dependent on compositional effects. In recent years the number of oil reservoirs being used for gas storage purposes has increased greatly, and there has been at least one published account of additional oil recovery resulting from gas cycling a depleted oil reservoir after repressur-ing with dry gas for storage purposes. Additional oil recovery from oil reservoirs resulting from gas storage operations could become an important secondary recovery process. This is especially true since the use of natural gas in large metropolitan areas continues to increase and more gas storage volume near these areas is needed. These facts provided the motivation for the work reported here. This paper reports on a study of the inter-relations of composition, saturation and pressure changes which occur when hydrocarbon gas is injected into an oil reservoir system. From an understanding of the process, prediction methods may be developed for use in forecasting the secondary recovery products from gas storage operations in oil reservoirs and, consequently, .the economics of such projects can be developed. The process of storing hydrocarbon gas in an oil reservoir and the cycling process both involve the transient multi-phase flow of oil reservoir fluids with changing fluid compositions. There is a scarcity of work published on the subject. One of the first laboratory models developed to study a problem similar to the one posed here was published in 1948 by Standing, Lindblad and Parsons. l They developed a model to study gas condensate recovery by gas cycling, including the effect of heterogeneous reservoir permeability. Their results showed the compositional effects of injecting a gas of known composition into a two-phase condensate reservoir of known composition. A major finding of their study indicated that maximum oil recoveries from gas cycling projects result when low cycling pressures are used. Previous to their work it was generally considered

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

By Henry M. Howe

My attention has been drawn within a few days to a series of articles in Volume XVIII of the Engineering and Mining Journal, 1874, by Mr. J. A. Church, in which it is stated, among other