Search Documents

By Edward J. Bagnall

The major raw material feed properties of size distribution and chemistry are examined in relation to their effect on sinter operating conditions, plant productivity, sinter physical quality, reduction- degradation characteristics and sinter texture and mineralogy. The resultant physiochemical properties of these sinters are related to their behaviour in subsequent ironmaking operations.

Jan 1, 1977

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By Jean-Marie Deschamps

In an approach to the complicated study of bauxite from Les Baux de Provence it is necessary to consider the paleogeographical context of all the bauxites in southern France. These bauxites are of Karstic type, belonging to a metallogenic area extending from the Pyrenees Mountains to the Alpine Massif. Within this area each deposit does not always correspond to the same geological period. There are differing opinions regarding the origin of Karstic-type bauxite and a discussion of these various theories is beyond the scope of this paper. Bauxite of Les Baux, in Provence, was discovered in 1821 by the chemist, Berthier, near this picturesque village located in the region of Arles. It is Les Baux from which the name of bauxite originates. For a long time this bauxite was of no interest because of high silica 'and mediocre alumina content. Besides, the calcium carbonate content is somewhat high and is one of the main characteristics of Les Baux bauxite. The problem of exploration of the Les Baux deposit has been to prospect minable zones according to traditional norms where silica and carbonate are low.

Jan 1, 1977

By D. R. Spink

An historical background is presented to provide a basis for the lack of normally expected developmental effort over the first 20-25 years of viable zirconium production operations. This is followed by a description of developing technology, which is the result of years of research and piloting effort directed to the development of a more economical method to produce high-grade metallic zirconium. It is predicted that many of the process improvements described will have a significant impact on future zirconium production methods and consequently on future prices and markets.

Jan 1, 1977

By A. Azis

The problem of expressing a nation's mineral resources in terms that convey a sense of economic reality poses a great challenge to those charged with keeping government policymakers informed. A model is presented that can be used to simulate and examine the effects of, for instance, differences in levels of output, transportation costs, mining costs or selling prices on the exploitability and expected order of development of new mineral deposits. The model in its present form can be used to screen, as a first cut, the economic from uneconomic deposits in cases where little or nothing is known about them in detail. To date, this has generally been done - reluctantly - by subjective judgments. This model provides an improvement on the "informed opinion" approach, as it forces those who use the model to be both systematic and explicit in their assumptions. Moreover, the procedure is repeat- able and each step can be defended and justified. Implications can be examined of the uncertainty associated with many of the variables. The model is entirely too general to be of use for actual feasibility studies. It is not useful, in the case of speculative or little-known deposits, to provide a model that has an input format more detailed than the information that is likely to be available. Should the user see a need for it, the model can easily be expanded to allow for the input of more detail or more variables.

Jan 1, 1977

By Richard H. Oitto

The Bureau of Mines and Kaiser Steel Corp. are cooperatively demonstrating the shield-type roof support in the longwall mining of a 10-1/2-foot-thick coalbed at the York Canyon mine near Raton, N. Mex. As part of the demonstration, the shield supports have been successfully and safely moved from a completed longwall face to a new longwall face. When these shield supports were moved in 1976 they were the largest and heaviest longwall support system in use in U.S. coal mines. The shield supports, preparations for moving them, the actual move, and installation at the new face are discussed.

Jan 1, 1977

By Donald W. Barnett

U.S. environmentalists have tended to oppose all new energy developments. Their efforts may be counterproductive because opposition to, say, offshore oil directly leads to the continued use of other energy sources that may have a higher social cost. Rather than attempting to eliminate all pollution from energy production, which would be prohibitively expensive, one should minimize the social cost of energy production for the given demand. Linear programming is used to rank various oils (California State and O.C.S., Gulf of Alaska, Prudhoe Bay, Athabasca tar sands, oil shale and certain foreign crudes) in terms of their social desirability. The objective is to minimize the cost of supplying the California market, subject to resource, sulphur and oil spill constraints. Social desirability is indicated by the inclusion of the oil in the optimal solution and the size of the associated shadow price. the larger the shadow price, the greater the benefits of increased production. The more negative, the greater the cost associated with forcing consumption of that fuel. The environmental shadow prices indicate the size of the trade-off between a particular environmental standard and minimum cost. The trade-offs can be surprisingly large. any reasonable spill standard can be achieved by changing the development pattern. Generally, the further offshore, the smaller is the environmental degradation, but the more expensive is the oil. Foreign oils can be economically and environmentally inferior to domestic oils. Crude from the California O.C.S., San Joaquin Valley end Prudhoe Bay appears a valuable resource, while the Gulf of Alaska, synthetic and foreign crudes appear marginal to submarginal.

Jan 1, 1977

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

The relevance of borehole and bore core evaluation to the design of underground coal mines is illustrated by considering the technical parameters of colliery design and the information from which they are constructed. The nature of this information is described, together with some methods for its storage, processing and presentation. Geophysical exploration techniques are compared as information sources. It is concluded that borehole and bore core evaluation is relevant and necessary for colliery design, but that optimum results will be obtained if drilling can be combined with geophysical techniques. Because of the inherent uncertainties in prediction of mining conditions the necessity of obtaining as much information as practicable from drilling evaluation is also stressed.

Jan 1, 1977

By Robert M. Lewis

Silica sand deposits are usually contaminated with various heavy minerals which must be removed to make the silica useful for flat-glass production. Research was undertaken to develop a better procedure for producing flat-glass-grade silica. Batch tests revealed that anionic detergent-type reagents had considerable promise. Pilot plant tests were run to compare the effectiveness of anionic detergent-type reagents with petroleum sulfonate in the removal of heavy minerals from a potential glass sand. Another slightly modified commercial procedure also was evaluated for comparison. In the pilot plant trials, utilization of the anionic detergent potation reagents did not produce quite as good results as petroleum sulfonate. It is likely that flat glass-grade sand could be produced with the anionic detergent reagents if more extensive pilot plant tests were conducted.

Jan 1, 1977

This Bureau of Mines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By Arturo M. Morales

INTRODUCTION Manganese carbonates are nodulized by Cia. Mineral Autlan, located in Ongongo in the state of Hidalgo in Mexico. This kiln is fed minus 15 mm material at the rate of 1870 tpd. About 920 tpd is nodulized into a commercial product having a size range of 15 mm to 12 mm. The kiln also produces about 320 tpd of minus 12 mm fines and 40 tpd of chimney dust. Currently, the minus 12 mm fines are being recirculated to the kiln and the chimney dust is not being utilized. It has been found that there exists a market for manganese to be used as feed to the ferromanganese and silicomanganese furnaces. However, a coarse, lumpy feed can only be used in these furnaces. Accordingly, it has been proposed to screen the fines at 6 mm and agglomerate the minus 6 mm fraction along with the chimney dust and suitable binders. This paper presents the results of a feasibility study and test work aimed at producing an acceptable agglomerated product from the kiln fines for use in the ferromanganese and silicomanganese furnaces. Since the agglomerated product will have to be handled and loaded into trucks in the kiln area and transported over long distances, a minimum strength of 200 N is expected to be necessary. They should also have enough initial strength to be stockpiled and result in a minimum of breakage. A third important requirement is that the agglomerates should be resistant to disintegration during combustion. The recirculating fines were to be agglomerated in their original state, if possible, that is, without grinding. This eliminated the possibility of pelletizing as an agglomeration method. Based on a few laboratory trials, the briquetting method seemed most attractive, and a test program was initiated to explore the briquetting process.

Jan 1, 1977

By Michael W. Roper

McDermitt mine is located southwest of McDermitt, Nev., ½ mile north of the old Cordero mine. Geologic structure of the district is that of a Miocene age collapse-type caldera in a region of Basin and Range normal faulting. The McDermitt ore body possess a tabular, gently dipping configuration within 150 ft of the surface over an area 2200 x 2500 ft. Indicated ore reserves are 3 million tons at 10 lb Hg per ton. The ore zone averages 20 ft in thickness and consists of cinnabar (HgS) and corderoite (Hg3S2Cl2) deposited parallel to bedding in argillized Miocene age tuffaceous lacustrine sediments. The ore body is localized above a silicious sinter-silicified lake-bed breccia. This "opalite" breccia unit possesses a gently dipping, apronlike configuration, striking northeast, parallel the trend of the Cordero deposit, and thinning to the north and northwest.

Jan 1, 1977

By James F. McConnell, Charles W. Statler

Pennsylvania's existing large coal-fired units are limited to 2.0, 1.8, or 0.6 lb of sulfur per million Btu fired, depending on site location. Multi-stream coal preparation can be employed on system basis to extract the highest quality fraction of coal for use in units requiring the lowest sulfur. The middling fraction can be directed to units permitted higher sulfur. General Public Utilities Corp. has concluded that it is feasible to advance the state-of-the-art of heavy media coal preparation to produce an intensively cleaned primary product of 1.3 sp gr of less than 0.6 lb of sulfur per million Btu for the new unit and a middling product of 2.0 lb of sulfur per million Btu for existing units.

Jan 1, 1977

By M A. Ward

On 23 May 1977 the Hon Mr George Gair announced an amalgamation of the present Ministry of Energy Resources, the New Zealand Electricity Department and the Mines Department. Hopefully it will prove to be the solution of many national problems in energy planning and policy making, in energy distribution and use, and energy discovery and production. The name of this new giant is the Ministry of Energy which gives a firm indication of its future direction. For those amongst us involved with mineral energy resources the establishment of this new department must be encouraging. For those amongst us who are involved in non-energy side of the mineral industry it is the very opposite. The loss of the Mines Department a year short of its centenary is a loss for the mineral industry without a doubt - but how much of a loss?

Jan 1, 1977

By Kiyoshi Sugasawa

At Sumitomo Metal Industries, technologies for manufacturing metallurgical coke have been developed, under the names of Sumicoal System and DKS formed coke processes. Sumicoal System is the process utilizing approximately 70% conventional fine coal, 30% briquettes charge, and 2-3% caking substance. This technology was industrialized in 1975, and now the blending ratio of non-coking coal has reached up to 20%. On the other hand, a large scale demonstration plant using the DKS process was constructed and operated over one year. As the result of that test, it is thought that the DKS process has also reached the stage of industrialization. This paper will describe these new coking technologies.

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By Clark A. Sumner

An apparatus for agglomerating fine particles was developed in 1969 as a joint effort of Stauffer Chemical and O’Brien Industrial Equipment. Commercial sized units were built for agglomerating home dishwashing detergents. Recently, as a result of further pilot development, variation of bed depth and cage configuration has resulted in a means of controlling the amount of internal classification from a minimum, producing small agglomerates, to a maximum, producing compact rounded agglomerates. Little or no external classification of discharged agglomerates is needed. At maximum internal classification the agglomerates roll on a bed of fine particles rather than the shell resulting in increased agglomerate size.

Jan 1, 1977

By Carlos Kovacs-Figueroa

Complying with air pollution regulations created the need to dispose of increased sulfuric acid production by the Morenci smelter. As a result, a two-module leaching plant was constructed to leach Morenci flotation tailings. The leaching plant was equipped to perform the following operations: leach feed pumping, agitated leaching, two-stage countercurrent decantation, neutralization of leached tailings, and copper precipitation. Ancillary facilities were provided for neutralizer and flocculant preparation as well as precipitant handling and recovery of precipitates. Plant control is automatic from a central control panel supervised on a shift schedule by one operator and two helpers. Construction of the first module was initiated in April 1973 and leaching of tailings commenced in November 1974. Construction of the second module began in January 1975 and was completed in November 1975.

Jan 1, 1977