Search Documents

By A. Bentzen, S. S. Wong, W. K. Fletcher, B. J. Price, A. J. Sinclair

One hundred eleven pyrite samples from three porphyry-type deposits in the Canadian Cordillera were analyzed (many in duplicate) by AA spectrophotometry for Co, Ni, Cu, Pb, Zn and Mn. All elements have density distributions that are lognormal or combinations of lognormal populations. Co and Ni in pyrites show zonal patterns that relate generally to mineralogical zones in the porphyry systems, particularly if contoured as the Co/Ni ratio. High Cu and Mn values in pyrites also correlate with Cu-rich mineralogical zones. Other elements studied appear less regular in their distribution patterns, although Pb and Zn highs in pyrite seem to occur sporadically near the margins of porphyry systems. These data considered with two other studies permit construction of an empirical model for the distribution of certain minor elements of pyrites from porphyry systems of the calc-alkalic suite. In particular cases pyrite geochemistry shows potential as an exploration tool to aid in target definition for detailed exploration.

Jan 1, 1978

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978

By Peter L. Langsjoen, Kenneth L. Maloney

Ten small and intermediate-sized (4.5 Mg/hr to 113 Mg/hr steam--10,000 to 250,000 lb per hr) coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO, emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1978

By Paul C. McWilliams

This Bureau of Mines report analyzes data on the physical properties of quartzite rock from the Crescent mine, Coeur d?Alene mining district, Kellogg, Idaho, to demonstrate the use of multivariate techniques. After regression, factor, component, cluster, and discriminant analyses are discussed, these techniques are applied to the Crescent mine data. Three appendixes contain some of the required mathematical and statistical detail plus heuristic examples of three multivariate techniques --component, cluster, and discriminant analysis.

Jan 1, 1978

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

This paper describes the mechanical and electrical maintenance activities as practised at Isa Mine. The principles of preventative maintenance adopted are described as well as the basis of maintenance cost control.

Jan 1, 1978

By Adrian C. Dorenfeld

The lesser developed countries (LDC's) may be classified into two categories: 1) oil producers, and 2) non-oil producers. The non-oil producing LDC's, as a class, are at present in very difficult financial straits. (1) Since the quadrupling of world market crude oil prices in 1972, an ever greater share of the LDC's export earnings have gone to pay for oil imports, in-stead of national reinvestment. The LDC's inter-national debts--much of it to pay for oil--have soared to record levels, with consequent limits for future credits. (1) Again, this inhibits future national investments, and there does not seem to be an end to the future increase of Organization of Petroleum Exporting Countries (OPEC) prices. Indeed, some of the economic difficulties in some metal markets--particularly the imbalance of production vs. markets for copper, can be traced indirectly to the OPEC cartels' heavy-handed impact on copper producing LDC's which must produce copper at any price to meet their oil bills. (2) Among the major oil importing LDC's are the Philippines and South Korea. 50th nations have substantial cement industries. The South Korean industry is geared for major export markets in the Far East. Both nations have ambitious plans for economic growth in order to accommodate burgeoning populations with ever increasing expectations for high standards of living. These plans had some success, more or less, until the high OPEC oil cartel charges had to be borne. Now, in common with all oil-deficit areas, the Philippines and South Korea are seeking lower cost sources of energy. Both countries have coal deposits. In the case of the Philippines, the reserves are in scattered, relatively small deposits. Most of the coal deposits are faulted, folded and, in general present formidable production problems for limited reserves. Nonetheless production has been on the order of about 70,000 to 150,000 tons per year in the last 30 years. Prior productions (1920-1941) varied between 9,000 Co 150,000 tons per year. (13)

Jan 1, 1978

By J. J. Brummer

The possibility of diamonds occurring in Canada was first raised by W. H. Hobbs in 1899, who concluded: "that the apex of the fan of diamond distribution probably lies somewhere in the strip of the territory bordering James Bay on the east." This was based on the occurrence of diamonds in surficial sediments at various locations south of the Great Lakes. There are two recorded discoveries of drift diamonds in Ontario: (a) the Peterborough Diamond, 33 carats in size, poorly documented and found sometime before 1920;and (b) the Jarvi Diamond, 0.255 carat, found during 1971 in Sheraton Township near Timmins . Both discoveries were in surficial sediments and their source(s) have not been located. During 1960, Selco Exploration Company Ltd. started a heavy-mineral sample program of river gravels in the James Bay Lowlands of Ontario. This was continued by Canadian Rock Company Ltd. (1962-1963) and the Ontario Division of Mines (1973). The surveys discovered the presence of kimberlite minerals in gravel samples from streams draining the Moose River Basin. A total of 53 pyrope grains, four magnesian ilmenites and one grain of chrome diopside were identified from 32 sample locations. A study of the distribution of these minerals suggested the kimberlite source rocks to be located along the north margin or within the Kapuskasing gravity "high" in the area immediately south of James Bay. The Jarvi Diamond, found on an esker east of Timmins, could well have originated from this area. During 1965, an esker was sampled by the Geological Survey of Canada, and the results attracted attention to the area south of Lake Abitibi. At 9 out of 34 sites sampled along the Munro esker, Lee recorded the presence of pyrope garnets and very minor chrome diopside.

Jan 1, 1978

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By Young C. Kim, William C. Cassun

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. This paper describes the results of a case study in which a newly developed probabilistic economic analysis procedure was applied to the selection of a pit slope design at a large porphyry copper mine in the southwestern U.S. The paper also demonstrates the availability of the required data such as the probability of failure schedule and cost of failure models, under "real-life" conditions.

Jan 1, 1978

By W. D. Grimsley, R. P. King, J. B. See

Samples (15 to 20 g) of pre-calcined Mamatwan manganese ore or pure Mn 304 smaller than 48 mesh were reacted at temperatures in the range 1000 to 1300°C with samples of spectrographically pure graphite smaller than 325 mesh. Samples (1 g) of ore or pure Mn02 smaller than 48 mesh were reacted at temperatures of 1000 and 1200°C with pure graphite fines in argon, with graphite in carbon, .'1onoxide, and with carbon monoxide alone. In each case, the loss of mass as a function of time was recorded with a hermobalance. The rate and degree of reduction were found to increase with additions of carbon and with increasing temperature up to 1300oC, when they reached their maximum. The shape of the reduction curves, together with the results obtained from examination of the products of reaction by microscopy and X-ray diffraction, were used as the basis for a postulated reduction mechanism. Some details are given of an initial kinetic model that was used to verify the proposed mechanism. It was found that the reduction of Mamatwan ore by graphite at temperatures in the range 1000 to 1300°C occurs in two stages: (i) an initial stage during which the higher oxides of manganese are rapidly reduced to MnO with concurrent formation of CaMn2O4 and (ii) a longer stage during which CaMn2O4 and MnO are reduced to carbides by carbon dissolved in the ferromanganese phase.

Jan 1, 1978

By N. J. Themelis

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early thirties in the so-called Hadsel mills (Figure 1) mainly used in gold mines on the U.S. West Coast. A number of these mills were built in sizes of 20 to 24 ft. in diameter and five-six feet in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill (Figure 2), the Aerofall dry grinding mill and others. A tabulation of all known autogenous and semi-autogenous installations around the world was sent recently to the authors by Hr. G. J. Kushner of the Koppers Mineral Processing Division. In the size range of 24 to 32-ft. in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 36-ft. dia X 15-ft. long mills in Minnesota, powered by 12,000 hp. motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above one hundred and fifty mills was in operation prior to 1964.

Jan 1, 1978

This report describes the new Bureau of Mines Core Repository System (CORES) and presents the methods for selecting, processing, and storing physical samples and descriptive data for future reference by earth scientists. The system preserves splits of chip samples and longitudinally sliced segments of core. A records retrieval system provides for storage of data on microfilm and magnetic tapes and uses the keysort parameters of location and commodity for the identification of data.

Jan 1, 1978

The development of paraprofessional courses in metallurgy and related disciplines, by the Department of Technical and Further Education in New South Wales, is outlined in this paper. The changing nature of metall- urgical educational requirements is summarised, and various attendance patterns discussed. The potential advantages of the sandwich system of College attendance, to the more distant sectors of the mineral processing and metallurgical industry is outlined. Some of the likely future trends in technician education are presented. These include the need to respond to the changing expectations of technician employers, as shown by industrial surveys, the role of experiential learning, the need to integrate courses so that students can build on prev- iously completed courses, the possibility that future technicians will require a multi- disciplinary background and the provision of easier access to technical college facilities by potential students and industries.

Jan 1, 1978

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By Kenneth W. Kolthammer

Fundamentals of drying and the equipment used are reviewed. Dryers employed in the mineral industry include rotary dryers, fluid bed dryers, spray dryers, hearth dryers and rotary tray dryers. Concentrate characteristics, corresponding problems and handling methods are likewise discussed. Important factors include weighing and sampling, moisture content, market timetables, transportation availability and climatic conditions.

Jan 1, 1978

By T. H. Peters

The historical development of this program, dating from the construction of Nickel Park at Copper Cliff in 1917 to the various current projects carried out in the Ontario Division's program, is reviewed. Practices used to grow vegetation on stressed areas, the beneficial aspect of the improved aesthetic appearance of company properties from the point of view of public relations and the improved approach to the workplace by the employee are discussed. The revegetation of the tailings area and its gradual transformation into a Wildlife Management Area is reviewed.

Jan 1, 1978

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By Charles H. Etheridge

A new filter cassette is described which can be used with Coal Mine Dust Personal Sampler Units (CFR, Title 30, Part 74). The sealed cassette design reduces the chances of sample loss due to reverse flushing, impact or cassette opening. The filter capsule weight is approximately 400 milligrams and is stable for at least one year in storage. The alpha quartz content of the filter element is less than 5 nanograms per square millimeter of surface. The cassette is designed to be used with a new sampling head. The manufacturing costs of the new cassette will require an increase of approximately 30% in the selling price.

Jan 1, 1978

By Gene F. ] [Faufaul

This contract was concerned with the design, development, fabrication and testing of an improved tamper-proof filter cassette assembly for use in the, collection and evaluation of dust particulates, primarily in mining areas. This report presents the design effort, fabrication and tenting of five- prototypre unit$ as well as the design and production of 1000 filter cassettes with sampling heads. This new improved filter cassette has been tested and approved by NIOSH as meeting the requirements specified in the contract.

Jan 1, 1978