Search Documents

By Phillip R. Moyle

Several deposits in the Sheep Hole/Cadiz Wilderness Study Area (WSA) have small identified or potential for undiscovered gold and silver resources. One prospect area is a potential target for molybdenum. Most base and precious metals and one uranium deposit in the study area are of the fissure-filling, contact metamorphic type associated with late stage fluids of the Cretaceous Cadiz Valley batholith. Some evidence suggests limited Tertiary and Quaternary mineralization. Mineral deposits are controlled by faults, shear zones, and joints which strike northwest and dip northeast or southwest. Although undefined, calcium, sodium, lithium, and strontium brines are inferred within the study area. Some potential for oil and gas and geothermal resources is indicated by the interest private industry has shown in the eastern part of the study area. INTRODUCTION The U.S. Bureau of lines and U.S. Geological Survey conducted a mineral survey of the Sheep Hole/Cadiz Wilderness Study Area (p1. 1) which encompasses approximately 205,000 acres (83,000 ha) in south-central San Bernardino County, California. The U.S. Bureau of Mines studied the mineral resources of mines, prospects and mineralized areas; geological, geochemical, and geophysical investigations were conducted by the U.S. Geological Survey.

Jan 1, 1982

By Rexford D. Singer

The purpose of this study was to evaluate the current literature on the use of calcium chloride and ligninsulfonates as dust suppressants with respect to potential adverse effects on health or the environment. Calcium chloride poses little internal hazard to man and animals, but toxicity to vegetation in and around the area of application should be expected. The effects, however, should be considerably less than those observed from using calcium chloride as a road deicer. Except for trout, ligninsulfonates seem to pose little direct systemic toxicity problems in aquatic organisms, animals and man or any problem with local vegetation. Because of a greater volume of information on its use and effects, calcium chloride is recommended over ligninsulfonates.

Jan 1, 1982

By D. E. Barnett

"Paramount to sound aggregate resource management is an awareness of what resources exist. For the past six years, New Brunswick has been conducting granular aggregate resource inventories in and around urban centres as a means of documenting, both qualitatively and quantitatively, these resources.These aggregate studies require extensive ground truthing due to the often small nature of the surficial feature s as well as extensive foliage. Approximately 35% of the province's land mass has been mapped at a 1:50,000 scale as part of this on-going program. Reports are published annually and include data on size analysis, lithology soundness, abrasion and absorption.Aggregate deposits in New Brunswick frequently reflect the local bedrock lithology and, whereas much of New Brunswick is underlain by soft, friable sandstone of Pennsylvanian age, it is necessary to transport aggregate for higher-specification use considerable distances. Alternatively, the construction industry must turn to crushed stone as a source of asphaltic or concrete aggregate.Over 40% of New Brunswick's land mass is owned by the Crown, and aggregate resources are managed under the Quarriable Substances Act. Under this legislation, permit applications are reviewed by a Land Management Advisory Committee which consists of representatives from the various government departments involved.IntroductionSurficial materials either directly or indirectly form the basis of much of our economic activity, whether it is the field of agriculture, forestry, manufacturing, construction or other. Although sand and gravel have been produced and used since the day s of early settlement, the economic significance attached to such materials has only recently been recognized by both government and the general public."

Jan 1, 1982

By John Freer

A colloquium on solid-liquid separation was held by The South African Institute of Mining and Metallurgy on 23rd September, 1982, at the State Pavilion Auditorium, Milner Park, Johannesburg, to co-incide with the Electra Mining Exhibition. It was attended by about 150 delegates. Eight papers were presented covering: Geostatistics The School of Earth Sciences of Stanford University, the Centre de Geostatistique ofthe Paris School of Mines, and the Department de Genie Mineral of the Ecole Polytechnique of Montreal are cosponsoring the organization of a 2nd NATO ASI (North Atlantic Treaty Organization Advanced Study Institute), under the name of 'GEOSTAT TAHOE 1983', to be held at South Lake Tahoe, California, on 4th to 17th September, 1983.

Jan 1, 1982

"This paper describes an alternative method of vehicle control which uses a micro-processor to control the field current and armature voltage concurrently. The field tests carried out and the conclusions drawn from the basis of the paper.IntroductionIt is generally accepted that the main obstacle to a greater use of electric vehicles is the relatively poor range and performance when compared to alternatives such as diesel and petrol-engine vehicles. Much effort has been applied to the problem of increasing the energy storage density of batteries and considerable improvements are now being reported.Improvements in the efficient use of the stored energy, although unlikely to achieve the necessary increase in range and performance for a widespread acceptance of electric vehicles, can nevertheless make a useful contribution. Because the improvement in efficiency is achieved by a reduction in losses, it follows that the temperature rise in drive-train components is reduced. These advantages, coupled with the increasing cost of energy, make improvements in the efficient use of the stored energy desirable, if not absolutely necessary. To achieve this with the large and rapidly varying loads encountered during the operational use of a vehicle will require a more flexible system of control than that provided by the current limit. This paper describes an alternative method of control which uses a micro-processor to control the field current and armature voltage concurrently.The value of these parameters is selected to supply the power demand at the motor shaft, with the minimum losses in electrical transmission, thus increasing the efficiency with which the stored energy is used."

Jan 1, 1982

By Charles A. Sorrell

Two red muds, two fly ashes, and several aluminosilicate minerals were subjected to direct treatment with concentrated H2SO4 at temperatures of 175°C and below. X-ray analysis showed that virtually all the sulfate reaction products remained in the solid residue because of their low solubilities in x SO Substantial portions of the Al2O3 Fe2O3TiO2, Na2O, and K2O components of the materials reacted to form water soluble sulfates, which were then removed by H2O leaching at 55°C. The solid residue after water leaching consisted largely of amorphous silica and, in lime bearing compounds, CaSO4, The reaction and leaching processes were effective in removing all or nearly all the Al2O3. Fe2O3, TiO2, Na2O, and in lime components in the fly ashes, red muds, china clay, bentonites, the nephelioe fraction of nepheline syenite, and a plaster insulating brick composed of anorthite and mullite. Reaction with potassium feldspar and petalite took place, with formation of alkali aluminum sulfates, but the reaction rates and yields were extremely low. Potassium feldspar can be heated with Na2O and x O in air at 700°C for 24 hours, or with CaO at 1000°C for 24 hours, after which the reaction product kaliophilite, nepheline, and leucite-like phases, prove to be very susceptible to H2SO4, reaction and H2O leaching, providing yields near 100% of the Al2O2 content. An alternative method of H SO treatment consists of heating the sample in a silica tube and passing H2SO4 vapor over it. Preliminary results indicate that this method can be effective in enhancing the kinetics of reaction with the Al O component of potassium feldspar and offer the possibility that formation of Al2 (SO ) Fe2(SO4)3 and TiOSO4 can be accomplished selectively by taking advantage of the fact that the upper stability limits of the respective sulfates in the presence of H2SO4 vapor will be different.

Jan 1, 1982

By Barry N. Whittaker

INTRODUCTION Considerable progress has been achieved with long- wall mining in recent years especially in enabling increased rates and levels of output to be gained, higher standards of safety and increased usage of advanced technological developments. Longwall mining also has major long term advantages, prominent amongst which is general minimisation of the effects of pillars and room intersections giving rise to future instability problems as can be the case with room and pillar mining operations. The fact that longwall mining is not presently limited by depth below surface inclination of seams or thickness of seam to be worked strengthens its position as the most popular underground mining method for extracting coal seams in Europe. Its wider application in North America and Australia can give rise to significant economic benefits coupled with higher levels of safety and recovery of coal. This present paper reviews recent progress achieved and draws attention to the more important factors influencing longwall mine design and layout. LONGWALL STRATA PRESSURE ABUTMENTS A longwall gives rise to major redistribution of strata pressures. The roof behind a longwall is normally allowed to cave and permit subsidence of the overlying strata and eventually giving rise to a trough depression at the surface. Consequently, reestablishment of strata loading within the caved region behind the longwall depends upon effective caving and subsequent recompaction. This requires sufficient depth pressure and/or adequate width of extraction in relation to the depth to achieve breaking of overlying roof beds necessary to reload the extracted region. Figure 1 shows results of an analysis carried out by Whittaker and Singh (1979) indicating the pattern of redistribution of vertical stress around a longwall in the plane of the seam. The analysis represents the average depth of longwall working in the UK, and was performed using a stress balance assumption of compatibility before and after mining. The main stress abutments are indicated by (1) the front abutment strata pressure zone which travels with the longwall, and (2) the flank abutment strata pressure zone which

Jan 1, 1982

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By I. W. Farmer

Case histories are introduced to illustrate how an understanding of the mechanics of deformation of mine structures associated with longwall layouts can be used to improve stability. Particular examples include: (a) deformations associated with longwall caving, (b) the effect of support pressure on roof deformation above a longwall face, (c) the effect of pack design on longwall access road closure, (d) the effect of rock deformation characteristics on floor heave.

Jan 1, 1982

By Bradley V. Johnson

This publication summarizes the in-house and contract research and development projects conducted since 1974 by the Bureau of Mines for the control of noise and vibrations from surface mine blasting.

Jan 1, 1982

By V. K. Karra, A. J. Magerowski

An overview of the scope of a computer program meant for aiding the design of crushing circuits is presented. Effect of circuit variables like the screen separation size and the crusher setting is illustrated. For a better understanding of the logic behind the circuit sizing, a detailed commentary in the case of a starting example is given.

Jan 1, 1982

By George L. Wilhelm

Timber support of mine openings continues to be an effective system for ground support, due to its avail¬ability, flexibility, and ease of installation. Timber support of mine openings as a primary method to support loose rock has been replaced to a large extent by rockbolting and by filling systems. How¬ever, the many designs of square-set timber and varia¬tions of crib and stull support that have been developed to suit many stope configurations have proven reliable over many years of application. Integrated in modern excavation and stoping methods, timber remains an im¬portant ground support material for today's mines. ADVANTAGES AND DISADVANTAGES OF TIMBER SYSTEMS Timber, when used as a part of the total support system, is recognized for its unique support properties. More than a cover to prevent minor falls of ground, timber systems have been carefully designed to provide adequate support with sufficient compressive qualities to achieve a safe working environment in extremely diffi¬cult ground conditions. In some cases, a timber support method is designed to yield while retaining its protec¬tive support qualities. Little or no initial investment in equipment or plant is required for incorporating timber into the mining support system. Low cost cutoff saws and portable chain saws are sufficient equipment for effective use of dimen¬sioned (sawed) or round (stull) timber support. Until recently, small sawmills of various complexity were com¬mon at mine surface plants. Sawmills at the mine sites have generally been replaced by timber vendors' mills. Suppliers have been able to use efficient cutting and lumber handling methods to reduce the cost of mine timbers. Most suppliers will package dimensioned mine timber into bundles that are suitable for handling down mine shafts and on level conveyances. The principal disadvantage of timber as a support method is higher material cost and labor cost associated with its labor-intensive installation. Furthermore, stand¬ing timber reserves of mine quality wood are in short supply in some areas, and heavy competition exists for alternative uses of the timber supplies. Vendors are reluctant to supply large cross section dimension tim¬bers relatively free of defects. Some mine operations require 4.8-m (16-ft) lengths of firm timber over 0.09 m2 (144 sq in.) in section and these are difficult to obtain in large quantities. APPLICATION OF TIMBER FOR MINE SUPPORTS Timber used in mine support has been cut from many species of trees. A firm hardwood with physical properties similar to western Douglas fir has been pre¬ferred in the US. Other harder and softer woods, how¬ever, have been used when readily available or where the specific strength or crushing quality of the wood is a desired specification of the support system design. Hard¬ wood, commonly oak, has been used where maximum crushing resistance is required. Mahogany and fir are widely used for shaft guide timber. Normally, timber is used with its core axis parallel to the long axis of the timber dimension. However, in some cases, it is placed normal to its core in a "butt" log position, so as to provide maximum resistance to abrasion of the ore passage adjacent to the cut end of the block. By selective placement of timber block¬ing, controlled resistance to ground closure can be achieved which will prevent early failure of primary sup¬port members of the timber structure. Timber is widely used in modern mining operations as a construction member for chute-lip support. These designs are tailored to each operation to conform to the dimensions of the haulage equipment being used. As a construction material, wood requires none of the spe¬cial equipment necessary for placement of concrete or steel support. Placement of these alternate support ma¬terials requires carefully dimensioned and engineered excavation for their installation. Wood can be easily sawed to fit on location. The successful use of timber in heavy ground de¬pends on the careful and accurate placement of block¬ing and bracing to achieve the controlled yielding re¬sistance needed to support the mine opening. Similarly, frequency, size, and placement of top and bottom block¬ing stulls in flat-bedded deposits are carefully determined to provide adequate support at the mining face. Con¬trolled caving through failure of the stulls may be required as the scope retreats from the earlier mined-out sections. The support program must achieve both of these dimensionless qualities by specification of stull frequency and size. The utility of the square set-system of ground sup¬port and timber support is described in Chap. 2, re¬printed from US Bureau of Mines Information Circular 6691. Four examples of effective use of timber for support of stoping and other mine openings are pre¬sented in other chapters in this section. The Gilman mine's use of Mitchell slice stoping described in Chap. 3 is an early modification of the square-set mining system. This application proved reli¬able for heavy ground and overcame some of the dis¬advantages of conventional square-set timber. Chap. 4 describes the Burgin mine's use of timber with other reinforcement material. This combination of materials achieved high strength and control with yielding com¬ponent members necessary for heavy, squeezing ground. Chap. 5 describes the Bunker Hill mine's use of square¬set timber in a new configuration that provides an effi¬cient and safe support for stoping using small load¬haul-dump (LHD) mobile equipment. Chap. 6 describes some considerations in placing the widely used stull in bedded ore deposits. Finally, in Chap. 7, cost calcula¬tions for

Jan 1, 1982

By B. N. Thompson

The main industrial minerals produced are non-metallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. The other minerals, some with minor production, include diatomite, feldspar, magnesite, sulphur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of Late Cenozoic acidic volcanic rocks.

Jan 1, 1982

By William G. Doepken

GENERAL DESCRIPTION The Henderson mine utilizes a highly mechanized, continuous panel-caving system to extract ore from a deep, massive, molybdenum deposit. The mine site, lo¬cated 80.5 km (50 miles) west of Denver, is situated at 3170 m (10,400 ft) above sea level in a steep valley on the eastern side of the Continental Divide. The mill site, located on the western side of the divide, is linked to the mine via a 15.5-km (9.6-mile) railroad tunnel. Mine production is scheduled to reach 27 215 t/ d (30,000 stpd) from the uppermost production level. This pro¬duction rate will have been reached within the four years following an intensive ten-year preproduction development program. A second production level, due to come on stream in later years, will expand production capabilities to 31 751 t/d (35,000 stpd). The mine, which employs approximately 2000, has blocked-out ore reserves of 220 Mt (242 million st) at an average grade of 0.42% MoS2. Geology The Henderson deposit is composed of two partially overlapping ore bodies that lie 1080 m (3600 ft) beneath the peak of Red Mountain. The ore bodies are entirely within a Tertiary rhyolite porphyry intrusive complex that has intruded Precambrian granite. The de¬posit is elliptical in plan with overall dimensions of 670 x 910 m (2200 x 3000 ft). In section it is arcuate with an average thickness of 185 m (600 ft). The top of the deposit is at an elevation of 2610 m (8700 ft) while the lower limits range from 2340 m (7800 ft) on the west to below 2100 m (7000 ft) on the east. The mineralization is relatively continuous in the ore bodies and consists of molybdenite and quartz in random to subrandom, intersecting, closely spaced veinlets. Cavability RQD (rock quality designation) * values measured from Henderson drill core and compared with the RQD values from the Climax and Urad block-cave mines in¬dicated that the Henderson ore would cave but with difficulty and that a high percentage of the cave ma¬terial would be blocky. Initial caving experience shows the Henderson ore caves easier and with greater frag¬mentation than was indicated by the RQD values. Pos¬sible reasons for this are: 1) The greater lithostatic load at the Henderson has a greater effect on caving and fragmentation than anticipated. 2) The relief of confining pressure due to caving action and brittleness of the rock is enhancing breakage. Mine Layout The Henderson mine layout was designed from its inception for a large-scale, rubber-tired, continuous panel-caving mining system. The ore body is vertically divided into three major mine levels (Fig. 1). The top¬most level (8100 level), which is 2469 m (8100 ft) above sea level, is the current mine production level. The intermediate or 7700 level, which is in the initial

Jan 1, 1982

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

US 4,192,852-Precipitation of iron values as a jarosite from a sulfate solution obtained as a byproduct in the hydrometallurgical processing of zinc sulfide ore The solution is cooled, partially neutralized, and clarified. The clarified solution is heated to a temperature of 80 to 100°C in the presence of sodium, potassium, or ammonium ions to precipitate substantially all of the ferric iron as jarosite The precipitate is thickened, filtered, and washed The residual solution may be processed for zinc or other nonferrous metal values R V. Pammenter and C J Haigh, assigned to Electrolytic Zinc Co of Australasia Ltd. Mar. 11, 1980. 16 pp. (423-42) Filed: 5-8-78 (903,524). Priority- Australia, 5-9-77 (PD0030) (Drawings below.)

Jan 1, 1982

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By John E. Rourke, O&apos

This paper describes some of the results of a project for the design and demonstration of subsidence monitoring systems for underground coal mines. The project was designed to test monitoring systems described in an earlier feasibility report (O&apos;Rourke and others, 1979). General objectives of the project were to develop reliable cost- effective monitoring systems for use above caving- type mining operations, over supported mines, and in urban undermined areas. Topics selected for discussion in this paper include a description of the instrumentation systems, the site conditions, problems of installation, resulting recommendations and an over- view of subsidence performance data obtained. There were some particularly difficult problems of installation to overcome at this site. Some of these could be experienced at any surface or under- ground project, others are probably more directly related to Western coal fields. Almost any subsidence monitoring program may face the following difficulties:

Jan 1, 1982