Search Documents

By I. M. Macleod

An adaptive steady-state on-line optimizing regulator is proposed as an integrated approach to the control of autogenous run-of-mine milling circuits. This optimizing regulator continuously estimates an internal model of the controlled process, and, based on this, determines mill fresh solids feed rate, mill water flow rate and sump water addition flow rate such that a circuit performance objective is optimized. The dual -requirement of controlling both the mill pulp load and the load of particles of grinding media size is thus directly and simultaneously addressed. The concept and theory underlying the operation of the adaptive optimizing regulator are discussed.

Jan 1, 1987

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By R. M. Yeates

Public concern over possible degradation of groundwater resources has resulted in an array of Federal laws and corresponding state laws to regulate contaminates from solid and hazardous waste. A mine owner must be familiar with environmental regulations which could impact his operation and must know what precautions and corrective actions to take in order to protect his mining operation from potentially expensive remedial actions. The Environmental Protection Agency (EPA), has issued few regulations controlling the management of mining wastes. Federal regulation of mining came primarily under the Surface Mining Control and Reclamation Act (SMCRA) administered by the Office of Surface Mining (OSM). Waste generated from the extraction, benefication and processing of ores and minerals was exempt from regulation under the Resource Conservation and Recovery Act (RCRA), which is EPA's major instrument in controlling surface contaminates. On December 31, 1985, EPA submitted to Congress a report entitled "Wastes from the Extraction and Benefication of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale", which will be referred to, henceforth, as the Congressional Report. This Congressional Report assessed the possible adverse effects of mine associated wastes. This report is the first step toward developing regulations with which EPA can regulate waste from the extraction, benefication and process of mineral ores.

Jan 1, 1987

By Martin C. Jones

This paper outlines the development of small diameter grouted piling, to deal with foundation problems in difficult soils conditions and in very restricted access areas. A number of applications are outlined to show the way in which these piles have been used over the last sixteen years in Canada. PICKERING GENERATING STATION - ONTARIO HYDRO UNDERPINNING OF SCREENHOUSE - TRASH DISPOSAL AREAS Between 12th July and 29th September 1971, 40 small diameter grouted piles were installed in the screenhouse at Pickering Generating Station. Access was extremely restricted as the screenhouse had been completed and the majority of mechanical equipment had been installed. The two ends of the screenhouse had been built on granular fill which overlies till and shale bedrock and settlements had been observed which it was decided had to be halted even though the rate of subsidence had decreased. Two diamond drills were employed to install 8 inch

Jan 1, 1987

By Morgans DJ

The aim of this paper is to highlight the social aspects involved in the preparation of environmental impact studies (E.I.S.'s) for mining developments. In particular, the paper will reveal that the social information provided in such E.I.S.'s can achieve much more than simply satisfying government requirements. Such information can form the basis of a strategy to deal with the settlement of a mine workforce in either an existing or newly developed community. A strategy of this type can go a long way towards avoiding many of the social problems and related industrial disputes often created in such circumstances. It will also be of significant benefit to the mining company in negotiating its infrastructure package with the local authority.

Jan 1, 1987

By Thomas H. Holley

This presentation will describe the underground excavation at the Bad Creek Pump Storage project. It consists of approximately 3,650 m of various size tunnels ranging from 4.2 m to 9.0 m finished diameter, a powerhouse cavern 45 m high by 135 m long by 22.5 m wide, and 422 m of 9 m diameter shaft. A total of 350,000 m of rock will be excavated, hauled, and placed in a submerged wier. Temporary rock support consisting of shotcrete and/or rockbolts is installed as required.

Jan 1, 1987

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By Flloyd J. M

A continuous oxygen probe,incorporating a SIRO2 solid electrolyte oxygen sensor which measured the oxygen potential of a small volume of gas enclosed above the melt's surface,was constructed and tested. The oxygen potential of iron-silicate slags in equilibrium with solid iron in the temperature range 1250 to 1300¦C were measured continuously for tests of up to 40 hours duration. Results were in agreement with those of previous workers using gas equilibration techniques. Tests on non- iron buffered slags proved unsuccessful due to corrosion of the probe's component in contact with the slag and an alternative material is Required.

Jan 1, 1987

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By Frank A. Peters

This description of process evaluation techniques used by the Bureau of Mines for studying proposed processing techniques has been prepared to provide those interested in using these studies with an understanding of the methodology. The methods used for preparing both capital and operating cost estimates are described. Each step in preparing the evaluations is described. Types of equipment costs are shown and factors used in the estimates are defined. Uses of the estimates are suggested and several examples are included. The accuracy of various types of estimates is discussed, along with an explanation of the reason for selecting the type used in the Bureau's process evaluation studies.

Jan 1, 1987

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By L. C. Woollacott

A computer-aid is described that is designed to calculate steady-state material balances for ore-dressing circuits. The program determines the material balance from a specification of the process condition. No mathematical models or data adjustment techniques are employed. As such the program complements existing simulation and material balance 'smoothing' packages. The process condition is specified using performance indicators. These are significant parameters in the industry with which all practising mineral processors are very familiar. The program employs an equation-oriented technique for material balancing and so has had to deal with the difficulties peculiar to that approach.

Jan 1, 1987

By Roger Cabos

El presente texto señala la necesidad de estudios microscópicos determinativos y cuantitativos como complemento de los análisis químicos, de forma que se explore la posiblidad de beneficiar el mineral oxidado por métodos convencionales.

Jan 1, 1987

By Philip U. Santacroce, James H. Meinholz

One-half of the $607 million Conveyance construction portion of the Milwaukee Metropolitan Sewerage District's Water Pollution Abatement Program is completed or under contract. 12,200 m (7.5 miles) of tunnel boring machine (TBM) driven rock tunnel from 2.5 m (8.0 ft) to 9.9 m (32.3 ft) diameter has been completed. This paper presents a review of TBM performance and a discussion of the pertinent geological conditions of the area.

Jan 1, 1987

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By Dean D. Turner

Exploration geochemistry requires computer processing for quick and efficient reduction and interpretation. An easy to use microcomputer based geologic workstation fulfills this need and allows the geologist to independently process geochemical data. Functions necessary for geochemical data processing are: 1)Digitizing; 2)Communications; 3)Data base management; 4)Statistical analysis; 5)Mapping analysis; and 6)General purpose applications (ie: word processing). A geologic workstation that can perform these tasks will yield significant advantages in processing and interpreting geochemical data.

Jan 1, 1987

By Richard H. Adams

INTRODUCTION With the discovery and depletion over the years of near surface ore bodies, exploration targets are tending to be at greater depth or overlain by various types of overburden which in some cases extends to considerable depth or is heavily water bearing. Access to these types of deposits for exploration and development often requires vertical shafts. This paper discusses the concept of small shaft engineering and construction, primarily for underground exploration but also for use as a low tonnage production facility or for mine ventilation. The option of a small shaft may be attractive in a number of cases, some of which are: The underground exploration of a deposit at depth where minimal expenditure is desirable until the potential of the deposit has been determined. The exploration shaft in many cases later serves as a ventilation way and second means of egress. Production of ore in a small tonnage/high-grade operation where decline access is impractical. For ventilation where other types of openings are impractical or would delay start-up of mine operations.

Jan 1, 1987