Search Documents

The paper reviews the majority of associations and institutions which operate in support of the Australian mineral industry. The review covers historical aspects of each organisation and the current activities and management structure. The linkages between the organisations through membership are briefly discussed. The paper comments on the evolution of the formation of the organi- sations and the networks between them that do exist and operate regu- larly. Rationalisation or a process to consider formation of new groups to fill gaps in the network are recommended for further research.

Jan 1, 1988

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

By V 9. 0 / 300 dpi

Papua New Guinea (PNG) stretches from the equator to Latitude 12° South and from Indonesia's Irian Jaya Province in the west to the Solomon Islands in the east (Figure 1). The population totals 3.5 million people who are mostly concentrated in highland valleys on the main island and around the coast. This paper outlines the history of mining, describes the natural, cultural and regulatory setting of mineral discoveries and highlights, by example, some of the more idiosyncratic environ-mental aspects of mining developments in PNG. It concludes with remarks on the progress made in the fifteen years since environmental matters entered the agenda for the establishment of a new mine in PNG.

Jan 1, 1988

By V. E. Ross

A model has been developed that describes the behavior of mineral particles and water in the cleaning zone of flotation columns. The possible detachment of particles from their sites of attachment at the bubble surfaces is related to the flux of bubble surface area with increasing distance from the interface between the collection and cleaning zones and the late at which floated particles are transported into the cleaning zone. The drainage velocities of floated and entrained particles are calculated from the drainage velocity of water and the properties of the particles. The effects of wash water and inhibited drainage in the froth are also explicitly accounted for.

Jan 1, 1988

In many metal mines in China,the 70B2 series of fans has been used for main fans for a long time.These fans generate higher static pressures than are required for the relatively high equivalent orifices of the ventilation systems of many of the mines. As a consequence, their running efficiency is common only around 30%. The loss of power is significant.

Jan 1, 1988

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

The equity market is now very much within a global village environ- ment, with various exchanges acting as agencies for the big casino. In this predicament, mining companies, who provide the most extensive, but relevant risk assessment information, will be best placed for favoured treatment by potential international investors: But what risk assessment information in summary form can be provided to support a resource/reserve statement? Even more importantly, does "objective" data exist, whose trends will support a resource/reserve state- ment? A prime need of the informed mining investor is to determine whether or not the resource/reserve statement is believable? But more importantly will it be realised? While the implications within the text of the majority of reports on resource/reserves suggests that the estimates are conservative, the record indicates that very few estimates are. In fact, to date, reports claiming to be conservative in respect of the overall grade estimate at a specfic cutoff have not reflected the realised grade at the stated cutoff; it has been more common for the realised grade to be lower than implied by the resource/reserve statement. Further, it is not uncommon for penalty elements to be understated and these components are rarely incorporated within resource/reserve statements.

Jan 1, 1988

By Percival T. J

Precious metal deposits containing fine-grained disseminated or dispersed gold-silver form by reactions between metal-bearing hydrothermal fluids and sedimentary host rocks. Host rock permeability and chemical composition exert a primary influence on the fluid movement necessary for any primary dispersion halos to form around ore bodies, and determine whether a disseminated style orebody itself will even form. Where the mineralized rocks are relatively unfractured the margins of the orebodies exhibit abrupt decreases in gold content, and strong corresponding decreases in the contents of other metals. Primary dispersion patterns of this type are difficult to recognize and commonly are only a few meters (or less) in width. If the host rocks were well shattered and broken before mineralization, remnant amounts of the hydrothermal fluids may be dissipated in fractures lateral to or above the ore zones. This causes geochemical anomalies to form with clays and silt- size silica within the fractures over distances of up to at least 30-50 meters away from the main orebodies. The tendency for large primary dispersion halos not to form around these deposits explains the disappointing results from so many drilling programs where no multi-gram gold-grade material was even found: if large areas and apparent large volumes of rock contain one gram or less gold that likely is the "orebody" and not a halo effect around high grade mineralization.

Jan 1, 1988

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By Netchaef P

A rationale is presented for the use of vegetation on mine dumps to minimise runoff and infiltration which become vehicles for potential pollution. The unique topography of mine dumps promotes high atmospheric advection which leads to extraordinary energy levels for evaporation discharge - the driving force of vegetation "pumps". This effectiveness is mainly a function of how well the vegetation will grow on a given site. Recent advances in technology allow water discharge by vegetation to be measured semi-automatically, accurately and cost effectively. As a result the basis now exists for a thorough evaluation of the optimum mine dump vegetation cover. This paper presents the current status of dump rehabilitation as seen by the mining industry. The significant prospects for use of vegetation to minimise mine water related problems with subsequent savings in capital and operational cost are also outlined. However, to examine the crucial questions of optimum hydrological ability, suitability and cost effectiveness of various types of dump vegetation a proposition is made to interested parties in the mining industry: The CSIRO needs potential study sites to evaluate the hydrological ability of vegetation under mine dump conditions.

Jan 1, 1988

In the first half of this century a mining industry was developed in Indonesia under Dutch colonial rule. World War II and the subsequent struggle for independence resulted in the destruction of most of the infras- tructure and much of the data. After independence, restrictions on for- eign investment and internal turmoil prevented re-establishment of a viable mining industry until the formation of the present Government after 1965 and the enactment of sound laws in 1967 to encourage foreign investment. Rebirth of the mining industry was followed initially by slow growth, but in the 1980's, spurred by the worldwide interest in gold, Indonesia has become the focus of an intense exploration boom for gold and other precious metals. 103 Contracts of Work for gold have been awarded since 1985 with Australian companies being the most predominant. Since 1985 three new gold operations have been commissioned and another two are nearing completion. Several more are undergoing feasi- bility studies. There is reason to predict that Indonesian gold produc- tion will grow to place the country in the ranks of significant producers during the 1990's.

Jan 1, 1988

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines-developed induction slag melting process is of concern to the titanium industry. The objective of the research was to determine the effect of removing the nonconductive molten calcium fluoride (CaF2) slag used as an insulator between the titanium and the segmented copper crucible. The data were obtained from single-induction-melted ingots prepared with no CaF2 insulating slag and an ingot prepared with the normal addition of 4 pct CaP2 slag. The results showed that the mechanical properties of single-induction-slag-melted and annealed Ti-6AI-4V alloy exceed the minimum values specified in "Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H." High-cycle, tension-tension fatigue testing yielded similar results. The data from 44 of the 45 specimens were contained within the typical scatter band for fatigue data on wrought Ti-6AI-4V alloy. Although the removal of the insulating slag is a desirable change, the data from the specimens with the previously standard 4 pct slag addition showed no detrimental effect from the slag inclusions.

Jan 1, 1988

By Hendrix JL, Nelson JH

Three ores (sulfidic, oxidized and carbonaceous) were analyzed to determine the effects of leaching time, ore depth, and ore mineralogy on cyanide species concentration. NaCN solutions were percolated through opaque columns filled with milled ore. Column design made liquid sample collection possible from various depths at specific times. The concentrations of weak acid dissociable(WAD) and total cyanide, Fe(CN)63 , Fe(CN)64 , SCN , and Cu(CN)43 were determined for each sample. Extended percolation time led to increases in WAD cyanide concentra- tions and decreased SCN and Cu(CN)43 concentrations regardless of ore depth. WAD cyanide concentration decreased while Fe(CN)64 concentra- tion increased with ore depth. Highest concentrations of Fe(CN)64- SCN and Cu(CN)43 were found in the sulfidic ore, with expected low WAD cyanide concentrations. Lowest concentrations of Fe(CN)64 , SCN 3 and Cu(CN)4 were found in the oxidized ore. Intermediate concentra

Jan 1, 1988

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

The Bureau of Mines has developed a system using a high-speed electropneumatic mechanism for the rapid (grab) sampling of dusts and gases during an explosion. The sampling system consists of an aluminum housing that incorporates two 30-cm3 preevacuated glass vials with rubber septums. Upon actuation, the sampling probe needle is driven through the septum with a pressurized air pulse, filling the tube with gas and dust from the mine explosion. After a predetermined time, the sampling probe needle is retracted by a second high-pressure air pulse to its normal (quiescent) state, allowing the sampling tube to reseal. The onset and the duration of sampling are independently variable and controlled by a time-delay relay package. This technique enables the monitoring of pyrolysis-charring in coal particles and the generation and combustion of the pyrolysis vapors in both large- and small- scale explosions. The following results were obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Laboratory: (1) Gas sampling of the leading edge of the flame front shows the large concentration changes, characteristic of the flame front; (2) gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen; and (3) the particles collected in the flame zone show signs of extensive pyrolysis and charring.

Jan 1, 1988

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988