Search Documents

By Chester R. Harris

With the passage of the Occupational Safety and Health Act (OSHA) on December 29, 1970 and the formation and growth of the OSHA Agency it spawned, public consciousness of occupational safety was raised. It became accepted that employees had the right to "a safe and healthful workplace". With the possibility of OSHA inspections, employ ers (particularly those with large workforces) began to give serious con sideration to engineering controls, safety programs, and training in a more uniform manner than previously.

Jan 1, 1991

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Richard Samson

"RésuméComme l'exploitation d'un gisement à grande profondeur représente un défi de taille et que la profondeur à laquelle se situe celui d'Ansil varie de 1200 m à 1460 m, nous avons dû mettre en place une infrastructure de surface d'envergure incluant un treuil de production et un chevalement d'une très grande capacité. De même, l'infrastructure sous terre a été proposée en tenant compte de ce fait important; d'ailleurs, l'excavation de deux puits circulaires dont l'un est en beton et acier et l'autre exclusivement en béton en témoigne. De plus, la plupart des cheminées principales qui furent excavées sous terre sont de forme circulaire.L 'exploitation du gisement s'effectue par une méthode chantier ouvert (abattage par longs trous), remblaye immédiatement âpres avec un mélange de roche stérile et ciment. Un taux de minage de 1750 tonnes par jour est requis pour assurer la production.L 'utilisation d'une technologie de pointe tels: les ventilateurs et les portes de ventilation sous terre contrôlées de la surface, un système de relèves macroséismiques, de chargeuses-navettes contrôles à distance, en passant par le dessin et la planification assistes par ordinateur nous permet d'optimiser l'exploitation du gisement Ansil.IntroductionEtant donne la grande profondeur a laquelle le gisement Ansil se situe, no us avons à mettre en place une infrastructure souterraine et de surface d'envergure pour nous permettre d'atteindre nos objectifs d'exploitation.Infrastructure de surfaceLa mine Ansil dispose d'une infrastructure de surface d'importance possédant une grande capacité (Fig. I). Les deux facteurs qui furent déterminant pour le dimensionnement des infrastructures furent le taux d'extraction de 1990 t/jour et la profondeur a laquelle I 'exploitation s'effectue, puis que cette dernière affecte le temps de cycle et la capacité de hissage.La première composante principale de I 'infrastructure de surface est un treuil de production a 2 tambours de 3.65 m de diamètre et de 2.0 m de largeur chacun. Ce treuil de marque Fullerton, Hodgart & Barclay construit en 1970, opère avec 2 moteurs de 930 kW a une vitesse de 700 m/min. et il a une capacité maximale de 32000 kg. Deux câbles d'acier de 45 mm de diarnètre et de 160 000 kg de résistance a la rupture servant au hissage des bennes d'une capacité de 12 tonnes. De plus, un moteur/générateur de 3000 kW (M.G. Set) raccorde au treuil de production sert a stabliser son alimentation électrique."

Jan 1, 1991

By Kilgour I

The installation of a final cleaning column at Ok Tedi Mining Limited was carried out to increase final concentrate grade in order to reduce concentrate handling, shipping and treatment charges and to reduce penalty payments. To fast-track the project a decision was made to install a full-size column on one of the two parallel circuits, designed on information readily available and utilising the experience of mill staff and an engineering consultant, rather than delay installation while a pilot scale program was conducted. A 3.66 m diameter by 12.8 m high column was installed to produce 40 t/h of final concentrate from a combination of rougher concentrate and recleaner concentrate. The column design and sparger system were by Cominco Engineering Services Limited.

Jan 1, 1991

By Kanaan Hanna

A joint research program between the U.S. Department of the Interior's Bureau of Mines and Cyprus-Yampa Valley Coal Company is being conducted at the Foidel Creek Mine, Oak Creek, Colorado. This program goal is to study the effects of state-of-the-art, high-speed, automated longwall mining on health and safety, and primarily, ground stability under various geological conditions. The Bureau installed an automated data monitoring system, known as the Ground Control Management System (GCMS), to monitor in real-time the effect of rapid mining on pillar and face loading, stress redistribution in and around the longwall panel, and caving characteristics of the roof. The Bureau's GCMS, combined with the company's existing monitoring systems, which include environmental monitoring, a computer programmable conveyor belt system, and gamma ray roof control thickness indicators, has been effectively used to improve safety at the face, increase productivity, and reduce production costs.

Jan 1, 1991

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By G. Yang, M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya

In the last 20 years, studies on controlled flow recirculation in various countries have been carried out in both coal and metal mines. These studies have shown that in addition to economic gains, partial flow recirculation can be used to provide mine workings distant from surface access points with the required volumes of air. These studies have also shown that the operation of fans and regulators, used in a recirculation system, will induce transients in gas flow and gas concentration. Various models have been developed to explain the problem. However, most have failed to incorporate important factors such as diffusion and dispersion in the modeling process. This study examines the theoretical background of gas emission transients from caved areas in coal mines, represents the problem by a "tank-airway" network model, and provides a possible solution. The study also presents the results gained from a laboratory model constructed to evaluate the major factors affecting the shape and duration of gas flow and gas concentration transients in an airflow recirculation system. In this model, the gas injection system was rearranged to simulate the variations in gas emission rates due to changes in air pressure. Within this model, a set of booster fans and regulators were used to generate the changes in air pressure within the model. Finally, the study presents an algorithm and a computer program GASTRAN, developed to analyze the gas concentration transients and calculate the pollutant transport levels in a complex ventilation network. The application of the program is illustrated by means of an example problem.

Jan 1, 1991

By Justus B. Deen

Given that the majority of mine ventilation operating costs are imposed by shafts, the need to predict the resistance of a planned shaft with reasonable accuracy is important. During conceptual design, shaft resistances are usually predicted by use of published friction factors, k, based upon lining and fitting configurations. More often than not, published friction factors do not directly coincide with "real" shafts, so their use is somewhat limited. For more accurate shaft resistance determination, equations both theoretical and empirical may be employed if there is detailed knowledge of the shaft. These equations treat the shaft resistance as discrete components, with their sum being the overall shaft resistance. This paper describes the basic shaft resistance equations and verifies these equations by comparison to field measured shaft resistances. Several shafts were examined which varied in depth, shape and fitting arrangements. Results are presented and conclusions drawn to show that the shaft resistance equations are accurate.

Jan 1, 1991

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By Silver EA

The Finisterre Range on the north coast of Papua New Guinea is the uplifted forearc riagio.n. of a modern arc-continent collision. The core of the range is composed of the P- nisterre Volcanics, an Oligocene''-arc terrane. The southern flank of the range consists of a clastic sedimentary sequence which is an uplifted accretionary wedge and collision complex. This clastic sequence can be subdivided into three distinct units. To the south of aiid structurally below the Finisterre Valcanics are the Mebu beds, an Oligocene- $arly Miocene sequence of volcanolithic turbidites. The Erap Structural Complex is south of, and structurally below the Mebu 43eds. , It consists of three subunits; the 3rly Pliocene micaceous turbidites of the Sukurum unit, contemporaneous pillow basalts AF{ the Basalt unit, and Late Pliocene to Pleistocene volcanolithic turbidites of the -Nariawang unit. The Quaternary Leron Formation, a fluvial to shallow marine 'clastic unit, is the southernmdst. and structurally lowest unit of the clastic -sequence The Finisterre Range is dominated by a fold-and-thrust belt with most thrusts "dipping steeply N. Melange fabric _ is developed in the vicinity of major thrusts. "ffle thrust belt strikes NW, oblique to the regional convergence direction, but no strike-slip motion is observed along NW striking faults.

Jan 1, 1991

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

By Roman Pyrih, Jim V. Rouse

Because cyanide is a naturally-occurring chemical, geochemical and biogeochemical mechanisms exist to retard or attenuate the movement of cyanide and its compounds in the subsurface and to degrade such compounds into low-hazard reaction products. The attenuation capacity of subsurface earth materials can be measured, predicted, and enhanced by simple and inexpensive procedures. The paper describes methods of testing the geochemical and biogeochemical attenuation capacity of the subsurface and offers general suggestions for methods of enhancing such capacity. It also presents examples of data which documents such attenuation.

Jan 1, 1991

By Lyman H. Hart

Michiquillay is a major copper deposit situated about 70 km (44 miles) northeast of Cajamarca in northern Peru (Fig. 1). It occurs largely in quartz monzonite in a shatter zone produced by the intersection of northwest- and northeast-trending fault systems. The geology is described by Hollister and Sirvas (1974). The ore deposit was drilled in 1963-1964 by Asarco, with results indicating a resource of 575 Mt (634 million st) averaging 0.72% Cu-0.03% Mo. A decision to bring the project to production has been deferred because world capacity to produce copper has been more than adequate to serve world requirements since 1964. The chain of events leading to the discovery of Michiquillay was set in motion by a decision by the management responsible for the Chilete mine to undertake an investigation of the surrounding area for a possible supplementary source of mill feed to bolster its decreasing lead-zinc reserves. Chilete, located 100 km (62 miles) inland from Pacasmayo, is the most northerly, important mining project in Peru, and little was known of the mineral potential north and east of that point. Relatively unimpressive reports of Colonial silver mining had attracted little investigation, and little was known of the regional geology. One study by Benavides (1956) had been made of the Cretaceous in the region of Cajamarca.

Jan 1, 1991

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

By Y. C. Kim

This paper describes the implementational aspects of a blast hole kriging system that has been developedfor the purpose of daily ore/waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore/waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBMIPC AT or XT computers, using the Fortran language and supplemented by a few assembly language routines for the bit- map manipulation. This paper emphasizes the practical implementation requirements of the system and discusses system design considerations.

Jan 1, 1991

By Yan. T. Y.

Uranium precipitation from an eluate using hydrogen peroxide has been studied in a laboratory continuous unit. The important process parameters were the dosage of H2O2, reaction pH and chloride ion concentration. In the process, the alkaline eluate is acidified to a pH of 2, then H2O2 at 110%-130% of the stoichiometric requirement is added, and finally NaOH is added to maintain a pH of 4 for one hour to complete the precipitation and settling. The chloride content in the system is controlled to 50g/L or below by rejecting part of the decant solution. The process has been successfully employed in commercial operations. The uranium recovery is complete, while the precipitate settles rapidly and can be processed to high purity yellow cake without filtration.

Jan 1, 1991

This paper reviews the current techniques employed in the prediction of subsidence and how they have been applied to partial extraction systems. The method using influence functions to describe the shape of the profile is investigated in detail and has been adopted to model the subsidence over workings in Huntly. It is compared with the profile methods developed in the United Kingdom and found to predict the subsidence profile more accurately than these methods.

Jan 1, 1991

By Churchill M

One of the significant changes which has occurred in the flotation sector of the minerals industry, over the last two decades, has been the successful development of the very large flotation machine. The last twenty years has seen the volume of the individual cell, available to the industry, increase by a factor of ten. Today, new mills, and existing mill modernization plans, can consider individual cell volumes as large as 85 m3 with the certainty that the metallurgical performance capability of the large machine is inherently as efficient as the smaller machine. The large flotation cell offers benefits to the user such as reduced floor space, lower total power, process control simplification, and reduced maintenance. However, the flotation machine size selection process, based on overall installation economics, must include such factors as process tonnage, flotation kinetics characteristics, and metallurgical performance objectives. This paper discusses the flotation machine size and circuit arrangement selection based on both metallurgical performance and economic considerations. A computer based flotation kinetic analysis technique, which has proven valuable in quantifying the metallurgical response of flotation circuits having different cell sizes and number, is utilized to illustrate the selection of cell size and arrangement best suited to a client's Requirement.

Jan 1, 1991

By Vincent Castronova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

A group of bisbenzylisoquinoline (BBIQ) alkaloids has been shown to exhibit various degrees of effectiveness in preventing silicainduced fibrosis in animal models (1, 2). The capability of these drugs to interact with phosphatidycholine vesicles and rat alveolar macrophages was studied using fluorometric and equilibrium dialysis methods. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, the chiral configurations, and the double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is highly effective in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In summary, this study indicates that alveolar macrophages exhibit large binding capacities for certain members of the BBIQ alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds, suggesting that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.

Jan 1, 1991