Search Documents

By C. van Loggerenberg, P. E. Venter

The paper covers a wide range of modifications that are of potential interest to the practical coal-preparation engineer. Unfortunately, the paucity of performance data does not permit one to draw conclusions. The authors do not appear to have a clear understanding of the Tramp (or partition) curve concept.

Jan 1, 1992

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By Alastair Torrance, George Boucher, Roger Keller

An investigative blast programme has been carried out to provide information on the best blasting methods to excavate Chek Lap Kok island in Hong Kong for the new airport. The objectives of the programme included the assessment of a range of blast design parameters and their influence on fragmentation. This has been evaluated by physical assessment, photo digitising of the muckpile and computer predictions. In addition, a model to predict the three dimensional muckpile shape has been successfully calibrated.

Jan 1, 1992

By Chris Twigge-Molecey

As emission constraints for metallurgical plants become more difficult to meet; control of major, multi-vessel, flue systems become more critical. Control instabilities can result in significant loss of system capacity or emissions to the environment. This paper will discuss the use of dynamic simulation techniques to optimize both the design and control strategies for these systems. A significant ,safety hazard is associated with pressure excursions from process upsets or equipment failures. Pressure rise rates of up to 10 kPajsec can occur. These cannot-be followed by conventional controls. Fail-safe high speed venting is required to protect both the furnaces and operating personnel'. Design options, sizing techniques and practical problems are discussed.

Jan 1, 1992

By Kadri Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. . The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1992

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau's surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 1992

By Yongjin S

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including Modelling.

Jan 1, 1992

By Jan Walaszczyk

The paper concerns the calculation of stresses and displacements in working area of room-and-pillar mining system of cooper ore mines. A three-dimensional rock mass model based on the finite element method has been developed. The complete strain-stress characteristic for pillars has been applied, but for the purpose of modeling the curve has been approximated by three segments of lines: - the first represents a behavior of pillar before a failure, -the second corresponds to a progressive pillar failure phase, - the third represents the part of the curve, where the increase of strains do not cause the stress changes, and it is called the residual strength. The criterion of model stability has been derived, which can be useful for predicting rockmass stability. The programs have been built, which allow to calculate stresses in bar elements, displacements in plate nodes, and estimate the stability of the model, which consists of plate elements and one-dimensional elements with a segment strain-stress characteristic. The programs were used to consider two different problems, which are connected with mining design and the exploitation systems.

Jan 1, 1992

By Timothy J. Haddon

For the mining industry in general and gold mining in particular, the past few years have been difficult. Economic conditions, coupled with growing regulatory restrictions, have led to increasingly important reasons for managing assets wisely. From a public company perspective, such asset management makes sense because it ultimately provides for an increase in shareholder wealth, and that is why we are in business. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the chief executive officer of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer-the Amax Gold shareholder? The gold industry has been under siege. We have just completed the third year with average prices below $12.85/ g ($400/oz). When finding, and/or acquisition costs and development costs to operating costs are added, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have, at most, a 10-year mine life. We are all scrambling to add reserves so we do not become extinct. As prices remain low, opportunities abound for increasing diminishing reserves. This is the time for the opportunistic company to take advantage of market conditions and that is precisely what Amax Gold has done. There are six components to running a successful gold business: • finding reserves through exploration, acquisition or joint venture, • financing the project, • permitting and constructing the project, • operating the project, • cash management and • communication.

Jan 1, 1992

By Mark J. Zdunczyk

Short Mountain Silica mines the Clinch Formation, an orthoquartzite, for silica sand. The operation is located near Mooresburg, TN, about 80 km (50 miles) northeast of Knoxville. Short Mountain is a local geographic name given to an area of resistant sandstone (Fig. 1). The area is part of the Clinch Mountain system that extends from eastern Tennessee to southwestern Virginia. The thick sandstone unit is more technically called a quartz arenite (orthoquartzite) that forms most of the mountain. In 1980, a Knoxville resident brought the Clinch Formation - Short Mountain in particular - to the attention of the large silica-sand producers as a potential silica-sand mine. Working with a local contractor who owned several hundred acres on Short Mountain, the Knoxville resident contacted interested companies. Many silica companies reviewed the property including Ottawa Silica Co., Pennsylvania Glass Sand Co. (both now US Silica Co.),Unimin Corp.,The Morie Co. and others. AFG Industries was the main market for the glass sand product from this potential mine. It had two plants, both within trucking distance from the site. All the silica sand producing companies, however, declined to develop the site. A few years later, Unimin Corp. decided to drill and evaluate the deposit. From that evaluation, Unimin leased the property but later dropped it. The relatively limited market for the Short Mountain product as well as Unimin’s recent acquisition of Carolina Silica were reportedly instrumental in the company’s decision to let go of the lease. Several other companies-unrelated to the silica sand industry - looked at the site but no one was interested in developing it. In 1986, J.D. Nicewonder, owner of coal mines in Virginia and Kentucky, was approached to investigate the site. Nicewonder began to develop the site with the intent to produce glass sand to supply AFG Industries. In May 1988, the first shipment of sand was trucked to AFG Industries.

Jan 1, 1992

By Tom McDonald

Test work and plant operation confirmed that semiautogenous (SAG) milling is a viable option for Inco's milling rationalization project at Sudbury only if pebble crushing is included. Throughput increases more than 50% with pebble crushing incorporated into the comminution process. The finer product of high-speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems. Inco Ltd.'s Sudbury operations are located in northeastern Ontario, Canada, about 400 km (250 miles) north of Toronto. Inco has 11 operating mines around the rim of the Sudbury basin. The mines currently produce about 11 Mt/a (12 million stpy) of ore. This ore contains pentlandite, pyrrhotite and chalcopyrite in mafic host rocks. The milling facilities are designed to produce 108.8 kt/a (240 million lbs/ year) of nickel as concentrate. This concentrate is further processed through Inco's smelting and refining facilities to produce nickel, copper and several other metals. Before 1991, -200 mm (-8 in.) ore was shipped to two primary mills. The Clarabelle mill had a design capacity of 29 kt/d (32,000 stpd). Frood-Stobie had a capacity of 16.3 kt/d (18,000 stpd). The flowsheets of these mills were similar. Two stages of open-circuit crushing were followed by rod milling and closed-circuit ball milling. The product from the comminution circuit, at 12% +250 mm (+65 mesh), was first passed through magnetic separators to recover magnetic pyrrhotite. It was then sent through a four-stage flotation process. The first two stages produced a high-grade copper-nickel concentrate. The final two scavenger stages produced a low-grade copper-nickel concentrate containing nonmagnetic pyrrhotite.

Jan 1, 1992

By J. M. Christian

Silver has been a much maligned metal in recent years. In the last three and a half years the price has fallen from around US$7.00 -$7.80 to as low as $3.50 this spring. It has consistently under-performed most other precious metals in the past few years, and has fallen to its lowest levels since the late 1940s in inflation-adjusted terms. Perhaps this is beginning to change. Since April, silver prices have outperformed gold and platinum. While this may continue in the years ahead, key questions remain regarding the pace and timing of any future silver price advances. I want to talk about the supply and demand factors that have led silver to its recent position. Also, I will outline a possible path for silver supply, demand, and prices for the next several years. Before I dive into my discussion of the silver market, allow me to explain who I am. One of the points we always make to clients early in a relationship is that, when you are listening to someone's opinions, you always must remember who it is you are listening to, and why he might be saying whatever it is he wants you to hear. So often, people take opinions from brokers, traders, or investment advisors as gospel truth, never stopping to ask themselves two key questions: Is there any reason to believe that this person knows what he is talking about, and, second, is he trying to sell me something, in telling me this.

Jan 1, 1992

By Chia A. H

This paper presents an overview of the development and operation of the PT Adaro Indonesia coal mining project. This operation is an initial two million tonne per annum mine, located in South Kalimantan, Indonesia.The paper places emphasis on some of the more unique infrastructure development and operational challenges that exist in such a remote location environment.A brief summary is also given of the Indonesian coal industry, its direction and position as a significant coal producing competitor for Australia.

Jan 1, 1992

By Liang Yinhuai

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover-caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

4.1 INTRODUCTION There have been numerous methods developed for predicting the final subsidence and final displacement profiles (Voight and Pariseau, 1970; Brauner, 1973a; Kratzsch, 1983). But for discus- sion purposes, they can be classified into six categories: theoretical, profile function, influence function, graphical, physical, and numerical modeling. The theoretical method employs mainly continuum mechanics theories and attempts to explain the mechanisms that lead to sur- face subsidence. Many models using nearly all kinds of material behavior have been developed. These include elastic (Salmon, 1963; Berry, 1964), plastic (Pariseau, 1968), viscoelastic (Iman, 1965), and elastoplastic (Dahl, 1969). The Profile Function Method is essentially a method of curve-fitting against the measured subsidence profiles in a particular mine or region. There are more than 20 profile functions developed empirically for nearly all major coalfields in the world. These include, to name just a few representative ones: Hungary (Martos, 1958), Japan (Hiramatsu and Oka, 1968), Russia (Avershin, 1947), United Kingdom (Wardell, 1965), and USA (Peng and Chen, 1981; Karmis et al., 1984). The NCB's graphical method in the subsidence Engineers' Handbook (1975) also belongs to the profile function method. The influence function method was first proposed by Bals (1931/1932). It was further developed in various periods and stages by Knothe (1957), Liu and Liao (1965), Brauner (1973a) and Marr (1975). This method is now widely used in various parts of the world. The physical models include sand (Litwiniszyn, 1959; Pariseau and Dahl, 1968) and gelatin (King and Whetton, 1958; Khair et al., 1986). They are used mainly to study the parameters that control subsidence behavior. The most popular numerical method is the finite element technique. It can simulate nearly every conceivable material behavior, inhomogeneity, bedding planes, anisotropy, and various boundary conditions. This versatility is absolutely necessary considering the ever-changing geologic and mining conditions encountered. In the following sections, only those methods that have been applied to US coalfields will be discussed. Furthermore, the methods for prediction of several key parameters such as maximum subsidence, maximum possible subsidence, and maximum displacement are discussed first, because they are the key parameters to be used in the profile function, influence function, and graphical methods.

Jan 1, 1992

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

By T. Vincze

Effective coal mine face ventilation, for remotely controlled and automated mining systems, is essential for the control of methane. The evolution of new mining equipment and methods has required changes and improvements in face ventilation methods. One emphasis today is on the use of remotely operated and automated mining systems that can be used to make continuous cuts of 6 m (20 ft) and deeper. U.S. Bureau of Mines research is studying ways to more effectively ventilate these extended cuts. Two face ventilation techniques that utilize either blowing brattice or a jet fan for deep cutting are examined in this paper. Bureau of Mines procedures for evaluating face ventilation systems are also discussed.

Jan 1, 1992

By J. S. Rapp

This report is based on existing reports and recently gathered field data. It discusses mineral resource potential of Tertiary playas in the Fort Irwin region. An estimated 1.3 million tons of measured salt "reserves", and 20 million tons of indicated salt resources, have been identified north of the fort. Other indicated resources include 300,000 tons of celestite, 800,000 tons of gypsum, and 10 million tons of selenite. Zeolitic tuff was mined south of Fort Irwin from 1978 to 1984, and unexplored occurrences are widespread. Calcium-bentonite is mined near Barstow, and more may exist, including valuable sodium-and lithium-based bentonites.

Jan 1, 1992

By Carol A. Hill

Native sulfur occurs with barite, celestite, and bioepigenetic calcite in the Culberson, Pokorny , and Leonard Minerals deposits, Delaware basin. The sulfur in these deposits, in "castile" masses, and in deposits of the Fort S tockton district have 6 34s values between +9 and -15. Native sulfur in the caves of the Guadalupe Mountains is somewhat lighter [(634s = -15 to -25)]. Barite in the Culberson, Leonard Minerals, and Comanche Creek sulfur deposits have 63% values of +35 to +73; celestite in the Culberson and Leonard Minerals occurrences have values of +38 and +36, respectively, and 87Sr/86Sr values of 0.707808 and 0.708138, respectively. Barite associated with sulfide, deposits, Guadalupe Mountains, have [634s] values of +41 to +62. Barite at Seven aeart Gap, Apache Mountains, is somewhat less enriched in heavy sulfur [(634s = +14 to +37)].

Jan 1, 1992

By Enugroho E, Nashution Y, Susanto M

PT Allied Indo Coal is the owner of the Parambahan Open Cut Coal Mine in the Ombilin Basin in West Sumatera with an annual production of in excess of 0.5 million tonnes/year of saleable coal.The parent company Allied Queensland Coal was one of the first foreign companies granted a contract of work. by the Indonesian Government. PT Allied Indo Coal is therefore a contractor to the Indonesian Government and pays a 20 per cent royalty of all coal mined.

Jan 1, 1992