Search Documents

By Jack G. Pippenger

The Coteau Properties Co.'s Freedom mine is a surface operation near Beulah, ND that produces more than 13.6 Mt/a (15 million stpy) of lignite. Coteau, a subsidiary of North American Coal Corp., ranks among the largest mines in North America. In 1994, Coteau ranked eighth in annual coal sales, becoming the largest mine outside the Powder River Basin of northeastern Wyoming. However, for the Freedom mine to stand alongside the Powder River Basin heavyweights, Coteau had to overcome several obstacles. These included a coal seam with three-quarters the heating value and overburden-to-coal ratios three times higher than Powder River Basin mines. Coteau's ability to compete has been built around a program of continuous improvements in productivity, cost efficiency and innovation.

Jan 1, 1995

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

The subject `access to land' is often seen as an item high on the list of matters of concern to mining interests not only in New South Wales but throughout the whole of Australia and other countries. Just what are the problems/issues of access to lands today? What is being done about them? What can be achieved? What is practical to achieve? And where does New South Wales sit in relation to all this? These and a range of other issues are addressed in this paper.

Jan 1, 1995

By John E. Urosek, Timonthy R. Watkins

Room and pillar mining accounts for approximately 73 percent of the active gobs used in the United States in 1993. The Mine Safety and Health Administration conducted field investigations on six different types of bleeder systems used to ventilate areas mined by room and pillar methods. This paper discusses investigations that were conducted at mines using four of these systems.

Jan 1, 1995

By G. E. Agar

In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to be done, wet or dry or a combination?

Jan 1, 1995

By Christopher J. Bise

During the past two decades, the emphasis on technological advances in US underground coal mining has focused on longwall mining. But there also has been a steady, although less spectacular, advance in the state-of-the-art in room-and-pillar mining. This has been stimulated by the successes of longwall mining in mine cost reduction, increased availability and improvements in haulage infrastructure, such as conveyor belt haulage. In addition, changes in management practices, such as nine- or 10-hour shifts, and marketing pressures have resulted in changes in the use of equipment. The net result of these changes has been the creation of modern room-and-pillar operations where average production levels currently exceed those considered very good 20 years ago. In fact, current production levels considered outstanding were considered unattainable two decades ago.

Jan 1, 1995

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

A geologic, petrographic and geochemical study has been performed on the pyroclastic flow deposits in the coastal area of East Zhejiang Province, Southeast China. This study leads to classification of the pyroclastic flow deposits into three associations: the extrusive type, the surge type and the ash flow type welded tuff associations. Through detailed investigation and comparison of the characteristics of these lithologic associations, with emphasis on the welded tuffs, a comprehensive model has been proposed to demonstrate the petrogenesis of the pyroclastic flow deposits.

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By C. T. Philipp

Recycling of waste is much preferred over disposal. This paper discusses the Enviroscience, Inc. (ESI) process, now being commercialized by MetWool, Inc., to recycle hazardous wastes using an extractive metallurgical process which is followed by vitrification of non-reducible metal oxides. In this process, volatile and reducible metals are reclaimed as their respective oxides and elements.

Jan 1, 1995

By Charles A. Edwards, Kenneth D. Merrill

The Construction of the Northeast Extension of the Baltimore Metro involved soft ground, compressed air tunneling. During the tunneling, gasoline and dry cleaning fluid contamination were encountered. Innovative approaches and solutions were developed to address these problems. Special emphasis was on the problem of compressed air pushing gasoline vapors into surrounding communities, resulting in an extremely dangerous situation and a public relations nightmare. Guidelines and standards were established for working in this contaminated environment. Also, through a proactive approach by all parties, all claims and disputes have been resolved.

Jan 1, 1995

By J. C. Cawley, J. Sottile, J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts and make the repair. Of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner and tested. This paper summarizes the development of the diagnostic system and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Comments on the system's performance are also presented.

Jan 1, 1995

By Robert B. Parsons

"The 1994 Quebec Budget included a significant overhaul of the mining duties sys-tem in that province: broadening the base and lowering the rate, all in the name of “ensuring the integrity of the taxation system"" and ""enabling the State to collect fair compensation "". The reforms hit hardest on the small, lightly-capitalized producer, by repealing the basic annual exemption, limiting the refund for losses, and significantly reducing the investment and processing allowances. There is some relief provided in the form of faster depreciation rates and a lower nominal tax rate, but the thrust of the overhaul is clear -higher taxes on the mining sector.IntroductionAlthough Quebec's mining tax regime represents under 10J0 of the province's revenue base, and was significantly reformed in 1979 and 1985, the May 13, 1994, provincial budget introduced further significant changes to the Mining Duties Act, The hope (on the part of the province) is to reduce the provincial ""subsidy"" for mining by $20 mil· lion per year by 1996."

Jan 1, 1995

By S. G. Ozkan

Boron minerals of economic importance are primarily colemanite, tincal, and ulexite. Turkey and the United States are the leading producers of boron minerals and compounds. Other production includes datolite in Russia and synthetic colemanite in Chile. This paper will discuss various types of chemical and physical treatments of boron ores to produce the marketable minerals and compounds that are consumed in commercial products.

Jan 1, 1995

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By Richard D. Doepker, Cathy A. Summers

Part 1: Physical Characteristics The physical and mineralogical characteristics of samples from five sources in the Western United States were determined using size analyses, microscopic studies, and point counts. These results were combined with leachability assays and the chemistry of leachates obtained during slurry tests to predict sample dissolution characteristics during column leaching tests. Part 2: Dissolution Characteristics Two columns of each sample were leached over a period of 3 years with synthetic rain. Residence times were between 2 and 11 weeks. The samples were subjected to daily and seasonal temperature fluctuations and wet-dry and freeze-thaw cycles. During the latter part of this study, a biocide leachant (sodium benzoate) was substituted for synthetic rain to assess the degree of dissolution caused by biological oxidation. It was found that the presence or absence of barite or carbonate minerals can be used to predict the leaching behavior of the column material.

Jan 1, 1995

By H. A. D. Kirsten

The professions are subject to a wide range of changing conditions, and are as a result forced to become more competitive. Although there is a need for specialization under these circumstances, no formal recognition, definition, or control of specialists exists. Some of the professions have attempted, over extensive periods of time, to resolve the issues involved, and have met with varying degrees of success. It appeared from the replies to a questionnaire sent to over one-hundred-and- .fifty professionals, that both advanced education and experiential training, are considered to be necessary qualifications for specialization. The opinion as to whether it should be lift to the individual to cal himself a specialist, or whether recognition should be based on peer review, was divided The majority did not want the number of specialists to be controlled The response to the reservation of work for specialists was ambivalent.

Jan 1, 1995

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining rate schedule, a fixed plant production capacity schedule, and finds the mining and cutoff grade sequence that maximizes the Net Present Value. This tool allows the Mining Engineer to quickly look at project sensitivity to various production capacities, commodity prices, and costs. A description of the algorithm is given along with examples of how it has been used at Newmont.

Jan 1, 1995

By M. Polat, G. Ahuja, S. Chander, M. S. Klima

A study was conducted to investigate the use of flotation in combination with dense-medium cycloning utilizing ultrafine (-10 um) magnetite, as an integrated process for high-efficiency cleaning of fine coal. The objective was to produce a high-quality (low-ash, low-sulfur) coal, while reducing the amount of non-magnetic material that would need to be removed by magnetic separation. Three dense-medium cyclone tests were performed using different underflow diameters to produce feed material for the flotation separations The use of different underflow configurations caused a variation in the pulp and solids splits, which changed the clean-coal yield and the magnetite-to-coal ratio of the cyclone products, and hence, the composition of the flotation feed. Flotation was used to separate the clean coal and to recover the magnetite contained in the cyclone overflow stream. Any ultrafine refuse material, which may have reported to the cyclone overflow stream, was also removed in this step, further upgrading the product. In addition, flotation was used to improve the overall yield by recovering a middlings fraction from the cyclone underflow stream. It was found that flotation was very effective in separating the coal (or middlings) from the ultrafine magnetite, even under variable feed conditions. Magnetite recoveries approaching 99% were possible using rougher-cleaner separations in a laboratory flotation cell. This paper presents the results from this study.

Jan 1, 1995

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995