Search Documents

By H. K. Taylor, B. Denby, L. D. Smith

Contributions by H.K. Taylor and G.A. Davis discuss the three papers published in Transactions IMM A, vols. 103 and 104, with responses by Smith and Dowd

Dec 1, 1995

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By K. Nielsen, J. Kristiansen

A series of laboratory blasting and grinding tests on three types of hard and competent rock (coarse-grained monzonite, fine-grained granite and very fine-grained gabbro) showed that a higher level of applied explosive energy enhanced grindability and produced a larger amount of fine (-0.106 mm) material. This confirmed reported industrial experience and the results of previous investigations. However, the results did not provide any information on the quantitative relationship between the energy applied in primary blasting and that required in subsequent comminution. Only about 1% of energy consumed in conventional grinding is used to create new surfaces, while power efficencies in cone crushers have been estimated at 70-80%. In blasting, up to 20% of explosive energy may be transmitted to the surrounding rock as elastic strain energy, leading to both primary rock breakage and the generation of microcracks

Dec 1, 1995

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By J. M. Mutmansky

"The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous miner- generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory- generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM ). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared. IntroductionIn many biomedical studies, researchers routinely introduce a dust mass into an experimental environment to assess the response of a biological entity, usually lung macrophages in vitro or a live laboratory animal, to the dust mass. To provide data of maximum usefulness, it is highly desirable to use dust with characteristics of actual mine airborne dust. The primary objective of this research was to produce dusts in the laboratory similar in chemical, mineralogical, and physical characteristics to mine airborne dusts. This paper outlines the evaluation of the physical characteristics of the lab-generated dusts.Particle shape analysis is perhaps the least-developed area in mineral-related particle science and technology. There are still no standard methods or instruments to scientifically quantify particle shapes. To date, many attempts have been made to characterize particle shapes. These procedures can be roughly classified into three categories:"

Dec 1, 1995

By F. G. Bell, S. E. T. Bullock

The investigation was undertaken as part of the environmental management programme that must be implemented on mine closure. It involved sampling and analysis of water from boreholes, the tin mine workings, trenches and pits as well as soil and dumps. Both ground- and surface water in the immediate vicinity of the mine was found to have been affected to varying degrees, mainly due to acid drainage from the pyrite dumps. Metal ions and toxic salts are taken into solution with increased acidity and precipitated in the soil when the pH rises again; there are concentrations of metal ions in the soils around the main dumps, but these do not seem to pose a major threat in a regional context. The low groundwater gradients, together with the dyke system in the vicinity of the main dumps and the impermeable nature of the Boschoffsberg rocks, make it unlikely that affected groundwater will migrate further than 1 000 m to the north and north-east. Nonetheless, it has been decided to remove the pyrite dumps

Dec 1, 1995

By P. Seppanen

Cemented fill was first introduced at the Keretti mine in 1952, but entailed high cement costs, the need for stope preparation, slimes handling, clean-up and maintenance, increased mine dewatering, segregation of fill and long setting times. In the 1970s research began into the use of iron blast-furnace slag as a binding agent and by 1989 Pyhasalmi, Vihanti, Keretti, Vammala and Enonkoski had saved US $11 000 000 by using slag binders instead of cement. Viscaria in Sweden and Tara in Ireland also use slag as 90-100% of total binder, although their backfilling methods vary. The main area of interest in slag research is determining the activation methods for initiating the binding reactions; it is also important to achieve other characteristics such as resistance to corrosion by sulphuric ion. New backfilling techniques developed during the 1980s included the use of high-density cemented tailings fill at Vammala and porous cemented rockfill at Enonkoski and Viscaria. Future developments focus on concepts such as integration of mining and milling with backfilling and the achievement of total underground disposal of wastes

Dec 1, 1995

By M. J. Reasor, M. DiMatteo, J. M. Antonini, K. Van Dyke, Z. Ye

"The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and laboratory animals. A variety of cellular and biochemical parameters are used to assess the silica-induced lung injury. The purpose of this paper is to introduce the use of luminok:Jependent chemiluminescence as a new method to study inflammation in both phagocytic cells and lung tissue recovered from silicaexposed animals. Chemiluminescence, or the emission of light, accompanies the release of reactive forms of oxygen when phagocytic cells are challenged. In this study, male Fischer 344 rats were intratracheally instilled with either silica (10 mg/100 g bw) or saline vehicle. One day after the instillations. a marked increase in the chemiluminescence was observed in the lung tissue and bronchoalveolar lavage cells recovered from the silica- treated animals when compared with the saline controls. The light reaction was markedly decreased by either superoxide dismutase or N-nitro-Larginine methyl ester hydrochloride. Superoxide dismutase is involved in the enzymatic breakdown of superoxide anion. while N-nitro-L-arginine methyl ester hydrocholoride, a nitric oxide synthase inhibitor, prevents the formation of nitric oxide. When superoxide anion and nitric oxide react. they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent that may be responsible for some of the oxidant lung injury that is associated with silica exposure. The use of luminol-dependent chemiluminescence may prove valuable as a method to measure the earliest events in the inflammatory process. and may be an adjunct in studying the mechanisms that produce inflammation. - Environ Health Perspect 102(Suppl 10):37-42 (1994) IntroductionResearch on inflammation has not produced a method that links the initial events of the process to the controlling events. Rather, a variety of parameters are measured that are the result of and not the basis of the inflammatory reaction. Parameters such as tissue weight, edema, blood flow, enzyme and protein release, or production of metabolites (prostaglandins, leukotrienes) have been used extensively. A method is needed that could be applied to cells of a particular type, groups of cells of different types, and even tissue, in an attempt to study the kinetics of the inflammation as well as being sensitive enough to monitor the early events of the process . Since inflammation is so complicated, the relationship between the control of the initial events and the oxidation process has never been explained nor studied in any derail."

Dec 1, 1995

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By T. R. Taubert, D. H. Carlson, J. H. Johnson

"ObjectiveDevelop a portable emissions measurement apparatus to sample and measure tailpipe concentrations of diesel particulate matter (DPM), carbon monoxide (CO), carbon dioxide (COJ, nitric oxide (NO), and nitrogen dioxide (NOJ under steady-state engine load and speed conditions during a 1-minute test.BackgroundThe U.S. Bureau of Mines (USBM) has a comprehensive research program to develop ways to reduce exposure of miners to diesel exhaust pollutants. Engine maintenance has been shown to have important effects on such exposure.Accurate measurements of tailpipe emissions are becoming an essential part of a good maintenance program for underground mines that use diesel-powered vehicles. Past studies of particulates in U.S. underground coal mines have shown that DPM alone may be present at concentrations greater than 1 milligram per cubic meter (mg/m3), half the 2-mg/m3 limit for respirable coal mine dust. A poorly tuned (smoking) diesel engine may be the sole cause for respirable dust concentrations exceeding the limit. Although there is currently no standard specifically for DPM in U.S. mines, regulatory steps are underway, and significant reductions of DPM levels in both coal and metal mines will most likely be required.Tailpipe emission measurements can provide diagnostic information to identify engine malfunctions such as clogged air cleaners, faulty injectors, or incorrect injection timing. In some cases, mine vehicle tailpipe DPM concentrations have been reduced up to 50 percent by engine maintenance and adjustments.An accurate measuring instrument would also be useful for determining the effects of exhaust control devices on tailpipe emissions. Little information is currently available about the overall effectiveness of exhaust controls after long-term use. Raw exhaust concentrations with and without the control device can be measured in underground mines, and from these data a control efficiency can be calculated. Knowledge of the effectiveness of exhaust control devices over time is needed to make intelligent decisions on bow to use and maintain these devices, and when to replace them."

Dec 1, 1995

By G. R. Chaudhury

Many base metals, such as copper, lead and zinc, are commercially extracted by thermal processing of sulphide concentrates. However, owing to the depletion of high grade sulphide ore reserves and to environmental legislation, efforts have been in progress for some years to develop methods for the extraction of metals from lower-grade oxide ores and secondary resources, and there are now examples of commercial-scale operations.

Dec 1, 1995

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By A. W. Kbair, L. D. Gehl

"INTRODUCTION The rock-bit interaction during the cutting process in underground mines has been a matter of great concern to mining operators, researchers and manufacturers, particularly after the passage of strict environmental laws. Coal cutting bears directly on airborne coal dust generation and rock cutting generates frictional sparks which may cause face ignitions, jeopardizing the productivity, safety and economy of the industry. It is imperative to investigate into the factors which have influence on bit we.ar. Hurt and Evans (1981) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits, and also worn bits were more responsible for ignition than the new bits. The results of a study (Khair et al., 1992) suggested that after 7% weight loss, the bit should be replaced. The polycrystalline compact diamond (PDC) tipped bits are reported to be cost effective in a study done by USBM (Twin Cities Research Center), and it was stated that the PDC tipped drill bits had 80 to 100 times longer life than the ordinary tungsten carbide (WC) tipped bits.This paper presents the results of the experiments which were conducted utilizing a coal cutting simulator at the laboratory of the Department of Mining Engineering, West Virginia University, USA. The description of the machine and the experimental set-up have been described elsewhere (Khair et al., 1989; Gehi & Khair, 1994), and therefore, will not be discussed here. The rock types which were used in experimen~ are Tennessee sandstone, Berea sandstone and Indiana limestone. The operating parameters include (1) drum speed, (2) water spray pressure and (3) bit type. Besides studying the wear characteristics influenced by the above mentioned variables, the effect of these parameters on the required cutting force, specific energy consumption, acoustic emissions rate and rise in temperature of the bit were also studied. A preliminary study was also done to compare we.ar characteristics of the WC bits with those of the poly-crystalline compact diamond tipped bits."

Dec 1, 1995

By S. L. Weber, V. Castranova, D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, M. Bhat

"The mechanism of bleomycin-induced pulmonary fibrosis is not ye: clear. Recent studies have shown that alveolar macrophages (AM) can be stimulated by bleomycin in vitro releasing inflammatory cytokines, suggesting that the interaction of bleomycin with AM is an important step in the drug-induced fibrotic process. Bleomycin is known to bind DNA and generate oxygen radicals through complexation with Fe2+ and oxygen. To provide,more insight into the cellular oxidative property of bleomycin, v.s have developed a fluoromicroscopic method using 2',7'-dichlorofluorescin diacetate (DCFHDA) as an oxidative fluorescence probe to study the deomycin-induced intracellular oxidation in rat AM and the inhibition of the oxida¬tion by taurine, a compound known to inhibit the bleomycin-induced fibrosis. Bleomycin at 5 to 20 ug/ml has a moderate stimulatory effect (1.87- to 2.66-fold) on the secretion of superoxide anion. A high concentration of bleomycin (20 ug/ml), however, inhibits cell response to zymosan-induced secretion of superoxide anion. At 4 ug/ml, bleomycin has no effect on cell membrane integrity or morphology but results in a significant increase in intracellular oxidation. This oxidative process is Fe2-,-dependent and is accompanied by an increase in intracellular calcium (35 nM). Both the intracellular oxidation and calcium rise induced by internalized bleomycin are inhibited by pretreatment of cells with varying concentrations of taurine (25, 125, and 187.5 uM). The inhibitory effect on intracellular oxidation .vas found to be 36, 57, and 60%, respectively. These results demonstrate a stimulation-inhibition relationship between bleomycin and taurine on re cellular oxidation at a subcytotoxic dose of bleomycin, suggesting that the oxidative effect of the intracellular bleomycin-Fe2 complex is important in the initiation of the fibrotic process. — Environ Health Perspect 102 (Suppl10):91-96 (1994) IntroductionThe pulmonary system is most susceptible to oxygen radical-induced diseases due to its constant exposure to the highest oxygen tension, and the potential encounters with oxidant gases such as ozone, nitrogen oxides, and toxic doses of dust particles. The lung is also a well-perfused organ and thereby vulnerable to the effect of circulating xenobiotics such as paraquat, and, bleomycin, which is known to cause pulmonary injuries (1). Alveolar macrophages (AM), which act as a means of defense by phagocytizing inhaled dust particles and microorganisms while increasing production of reactive oxidative species, have been shown to play an important role in mechanisms leading to oxidative lung injury and fibrosis (2-4)."

Dec 1, 1995

By A. W. Khair, L. D. Gehl

"This paper describes the mechanism of coal and rock cutting from quasi-static indentation through dynamic indentation to rotary cutting. The results indicate that during quas~static indentation, a crushed zone, and subsurface fractures develop. The crushed zone is a potential source of dust generation. Dynamic indentation produces a crushed zone due to the frictional resistance offered by the coal or rock during penetration of the bit. Confining pressure changes the mode of failure from tension to mixed tension and shear. The wider bit causes larger crushed zone and more dust generation. The rotary cutting is a combination of quasi-static and dynamic indentation which results in chip formation. 1. INTRODUCTIONThe trend from conventional mining to continuous machine-cutting of coal, using more productive machinery is inexorable. Intolerable levels of dust generated at the face is an indication of inefficient coal or rock cutting by these machines. The Federal Government of the United States paid about 11.7 billion dollars workman compensation to more than 470,000 miners with Coal Workers Pneumoconiosis (Newmeyer, 1981). Bieniawski and Zipf (1985) reported that annual benefit payments were about 2 billion dollars. The need for research m improving coal cutting 1s therefore paramount. The enactment of Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanism and cutting tool design. The European countries were also engaged in the same area of research, however, their emphasis was in the use of wedge shaped bits. In 1981, the United States Bureau of Mines commissioned the South West Research Institute to investigate the effect of operating parameters mainly on airborne respirable dust in order to provide a healthier and safer atmosphere for coal mine workers.A research program by the Department of Mining Engineering, West Virginia University, USA was initiated to study the fragmentation mechanism during coal/ rock cutting. The research program was divided into three areas of research, namely quasi-static indentation, dynamic indentation and rotary cutting."

Dec 1, 1995

By B. Z. Zhong, T. Ong, W. E. Wallace, W. Z. Whong, Z. W. Gu, M. J. Keane

"Abstract-Diesel emission particles (DEP) from an engine operating on the Federal Test Procedure VDC were dispersed in an aqueous mixture of dipalmitoyl lecithin (DPL). a major component of pulmonary surfactant and saline and were tested for genotoxicity using the unscheduled DNA synthesis (UDS) assay with autoradiography techniques in cultured Chinese hamster lung cells. A DEP sample from the same source was dispersed in dimethyl sulphoxide (DMSO) and subjected to the same assay. Both dispersions (in DPL and DMSO) were found to induce UDS in a dose-related manner. After separation of the sample into supernatant and sediment fractions. the activity of the DEP sample was found to reside in the supernatant fraction for the DMSO-dispersed sample; and in the sedimentary fraction for the surfactant-dispersed sample. These findings further indicate that genotoxic activity associated with DEP inhaled into the lung may become bioavailable through the dispersion properties of pulmonary surfactant components.INTRODUCTIONTHE mutagenicity of diesel emission particles (DEP) has been studied intensively (LEWTAS and WILLIAMS, 1986). Carcinogenic effects of diesel exhaust in exposed animals have been reviewed (NIOSH, 1988) and an evaluation of carcinogenic risks to humans from diesel engine exhausts has been published (IARC, 1989). Using components of pulmonary surfactant such as dipalmitoyl lecithin (D PL), dipalmitoyl phosphatidylethanolamine (DPPE) or dipalmitoyl phosphatidic acid (DPPA) dispersed in physiological saline, we have previously shown that diesel soots express mutagenic activities in the Salmonella histidine reversion assay system and in the sister chromatid exchange assay using the cultured Chinese hamster lung (V79) cells. Mutagenic activity of diesel soots dispersed in DPL, DPPE and DPPA was quantitatively comparable to and in some cases greater than, the activity expressed by an equal mass of soot extracted by dichloromethane-dimethyl sulphoxide (DCM-DMSO) (WALLACE et al., 1989).Unscheduled DNA synthesis (UDS) is accepted and frequently included, as one of the tests in the battery of assays used to assess carcinogenic-mutagenic potential -of chemicals (MITCHELL et al., 1983). In this study, induction of UDS in V79 cells by DEP, dispersed in the major component of pulmonary surfactant DPL, was carried out. The purpose of this study is to validate the suggestion generated from our previous work that mutagens associated with inhaled particles may be dispersed or solubilized in the phospholipid component of pulmonary surfactant and become active in such a phase (WALLACE er al., 1989) and to test the fractionated DEP sample using UDS assay for a more complete evaluation of its genotoxicity."

Dec 1, 1995

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

By J. B. Vander Sande, L. C. Rainey, P. Bolsaitis, B. Dirsa

"The structure and composition of silica-rich particles recovered by lavage from the lungs of three active miners with different medical histories were studied using high-resolution electron microscopy and chemical microanalysis. The results arc compared to the similarly determined structure and composition of respirable-size mineral particles obtained from roof-bolter dust-box samples from two coal mines of widely different bulk quartz concentrations. The results show that the lungs of the miners contain silica-based particles with structures not found in the mine samples. Also, the particle structures and compositions found in the macrophages were different in each of the miners. The rau.lu suggest the possibility that intracellular processes may affect the susceptibility of individuals to silica-induced pneumoconiosis. The cytotoxic and fibrogenic potentials of mine dusts result from the activity of their individual components. Whether this effect is additive or even mass (i.e., dose) related is questionable and has been the subject of many investigations. Particle size and size distribution of various constituent minerals, the surface structure and properties of individual particles, and the self-cleaning capability of the lung (i.e., the capacity of the macrophage system) may, among other variables, affect the pathogenic changes induced by dusts lodged inside lungs. Extensive epidemiological investigations conducted on miners from different coalmining districts, where equivalent dust exposures have been shown to result in vastly different frequencies of lung disease incidence, also confirm this hypothesis (1) In a recent study, Ferrer et al. (2) used energy-dispersive X-ray analysis (EDXA) to investigate the inorganic element content in pleura and lung in reference, silica exposed non-pneumoconiosis, and silicotic populations. Constant depositions of silicon and calcium were detected in visceral pleura, parietal pleura, and lung of the refence group and in visceral pleura and lung of the exposed non-pneumoconiosis and silicotic groups. Comparison of the silicon content in pleura between silicotic and exposed non-pneumoconiosis subjects showed a nonsignificant probability of difference, whereas there were no differences with respect to the silicon content in lungs."

Dec 1, 1995

By M. J. Reasor, J. M. Antonini, L. Wu, K. Van Dyke, Z. Ye

The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and· laboratory animals. Currently, no effective treatment exists for workers who may have been exposed to the inhalation of silica. The objective of this study was to develop an animal model in which we could evaluate the effect that anti-inflammatory steroids have on the acute silica-induced pulmonary inflammatory response. Male Fischer 344 rats were pretreated with either dexamethasone (2 mg/kg) or saline vehicle (i.p.) on days 1, 3, and 5. On day 6, the animals from the two groups were then intratracheally instilled with either silica (20 mg/0.5 ml saline vehicle) or saline vehicle (0.5 ml). Twenty-four hours after the instillations in the non-steroid group, significant increases occurred in total protein, total number of cells, neutrophils, and lymphocytes recovered from the lungs of animals treated with silica compared to saline controls. Silica also caused dramatic increases in the luminol-dependent chemiluminescence (LDCL) of lung tissue and bronchoalveolar lavage (BAL) cells. The LDCL reaction was markedly decreased by either superoxide dismutase (SOD) or N-nitro-L-arginine methyl ester hydrochloride (L-NAME). SOD is involved in the enzymatic breakdown of superoxide anion, while L-NAME, a nitric oxide (NO) synthase inhibitor, prevents the formation of NO. When the superoxide anion and NO react, they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent which may be involved in the silica-induced oxidant lung injury. When the animals were pretreated with the steroid dexamethasone, there was a complete protection against the biochemical, cellular, and chemiluminescent indices of damage caused by silica. The mechanism in which the steroid protects the lung from damage may be due to the ability of dexamethasone to block the induction of NO synthase. With further study in animals, the anti-inflammatory steroids may be useful in the treatment of silicainduced lung injury.

Dec 1, 1995

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995