Search Documents

By M. S. Klima, M. Fofana

The use of a laboratory-scale magnetic fluid-based separator for coal separations was examined. A Frantz laboratory magnetic separator was modified by fabricating new pole pieces of the appropriate geometry to provide the proper magnetic field gradients. Two separation chambers, which were constructed of Plexiglas, were designed to fit between the pole pieces. A commercially available, water-based, ferromagnetic fluid was used as the separating medium. The separating density was changed by varying the current intensity of the electromagnet coil. Both batch and continuous separations were made using 0.59 x 0.50-mm and 0.18 x 0. 15-mm coal. The results are compared to those obtained using organic liquids.

Jan 1, 1998

By John K. Kellis, Fazley Azhar

Advancements in AC drive technology offer conveyor designers a viable drive alternative for conveyor systems which require accurate load sharing as well as multiple drive systems. Recently developed AC drives have the ability to accurately control the output torque of AC motor. These AC drives, compared to current DC drives, offer superior performance characteristics while enjoying the benefits of an AC motor. Conveyor applications and case studies incorporating this AC drive technology are presented for review.

Jan 1, 1998

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By Kathryn Hindmarsh

The most common method for the concentration of cyanide in gold leach circuits is based on the titration of cyanide ions with silver ions. This can either be done manually as a titration with a visual end-point or by using one of several commercial cyanide analysers which are 'based on the same titration but use a potentiometric end point This method has 'its limitations in the case of some ores such as those containing high amounts of soluble copper and those that are treated at low (less than pH 9) pH values in that the titration results do not accurately reflect the concentration of cyanide which is available for the dissolution of gold. This paper will present the results of the development of a novel "active" cyanide analyser which is based on the rate, of the reaction between gold colloids and cyanide. Gold colloids have a deep red colour and can be very simply prepared and stored for extended periods of time when stabilized. t has been shown that colloidal gold behaves similarly to metallic gold, dissolving in aerated sodium cyanide solutions to give the colourless Au(CNh-ion, This allows the reaction between the colloids and cyanide to be monitored spectrophotometrically at 520 nm. An automated instrument has been developed around this concept which can analyse a filtered pulp stream every few minutes with periodic calibration using standard cyanide solutions, Results of test work on synthetic solutions and solutions derived from several Australian gold plants will be presented as will the results of a comparative evaluation with a commercial titration analyser on a local gold plant

Jan 1, 1998

By P R. Lock

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 km north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bedÆs life cycle of construction and placement and mucking of ore from the marker bed. Testing the marker bed for strength for use as a working platform was completed using a Clegg Hammer; good correlation to a Clegg Impact Value and the compressive strength of the stabilised gravel was found. This paper describes the use of a road stabilisation machine, tests conducted, monitoring and marker bed design and discusses underground placement of the marker bed and its performance.

Jan 1, 1998

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By Andrew I. Hustrulid

The discrete element method has successfully been used to model the behavior of material flow in transfer stations. With position, velocity, and applied forces for every particle and boundary in the simulation available at increments of 10-5 seconds, the next critical step is the presentation of this data in a concise and beneficial form. This paper discusses several methods of presenting the data from discrete element simulations that are used to improve the performance of a transfer station. These measurements are also used as a learning tool to better understand and visualize how material transfers from one belt to the next.

Jan 1, 1998

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By Courtney A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well 'as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 1998

By I Levy

At our Monkland Mine at Gympie, we operate a deep, narrow vein gold mine using hand held equipment, rail mounted haulage and narrow shafts. This is in many respects the old-fashioned way and is well suited most of the orebody geometry exposed to-date. We have also commenced some long hole stoping and we use alimaks for some jobs. The heart of our particular mining style is the employment and retention of experienced miners with remuneration based on productivity. We do our planning/monitoring/supervision down to the level of daily individual productivity. In focussing on cycles per se, we have chosen not to talk about drill and blast cycles or cycles for mine development, stope preparation or drawdown and haulage. Instead we have stepped right back from the operation as presently run and have adopted a very broad view of the mining cycle. We will in this presentation intertwine the ebb and flow of, exploration, project sponsorship, development, production and cash returns to owners. The time line considered spans both history and predicted future.

Jan 1, 1998

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Baafi E. Y

Dragline monitoring systems are normally the best tool used to collect data on the machine performance and operational parameters of a dragline operation. This paper discusses results of a time study using data from a dragline monitoring syste

Jan 1, 1998

By Glenn C. Miller

Cyanide is the most common lixiviant for extraction of precious metals, and its efficient use in open pit mines has contributed to the increase in world production of gold during the previous two decades. With this expansion of precious metals mining using cyanide, public concerns have developed in response to the inherent public perception of cyanide as a tox-in as well as a series of environmental problems that are directly or indirectly related to cyanide use in open pit mining. Some of these have technical or regulatory solutions, while others will require additional investigation before they can be resolved. The following discussion will summarize some of the public concerns regarding the use of cyanide in precious metals mining. The issue of cyanide use in large scale precious mining is controversial, and recent banning of cyanide use in open pit mines in Montana, or complete banning of cyanide in Hungary has reflected those international concerns. The underlying basis for some of the bans (e.g. Montana) reflect a general concern of the environmental impacts of mining, rather than specific issues related to risk of cyanide use. The human safety record for cyanide use, particularly in the developed countries is good, and cyanide is clearly the most efficient lixiviant for precious metals. Indeed, the relatively short lifetime for cyanide in the environment renders it one of the less problematic chemicals used for extraction of gold from ore. Mercury amalgamation or use of bromide as a lixiviant are certainly much more problematic. What, then, is the basis f~r the international concern about precious metals mines that use cyanide. Ifuse of cyanide for gold recovery is to continue, what additional infom1ation needs to be developed that will allow a better management of the risks of cyanide? Which of the concerns are directly related to cyanide, and which are indirect concerns that more related to effects of open pit mining. Under what conditions should use of cyanide be discouraged? DUl::ing June of 2000 the United Nations Environmental Program conducted a two-day workshop on cyanide use in mining that was attended by persons from the mining industry, regulators and environmental community. Support and attendance at this workshop reflected concerns by all three groups on further restrictions for cyanide use and the emerging potential for guidelines for better management of the catastrophic release of cyanide-containing mining waste. The following discussion is meant to focus-on those risks and explore the basis for an often negative reaction to precious metals mining using cyanide. It is presented in the format of a statement, followed by a discussion. While admittedly provocative, the statements are meant to express the concerns? of the public regarding cyanide and the mining industry.

Jan 1, 1998

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

By Tim J. A. Smith

Fundicion Refimet S.A. has operated a custom copper smelter at La Negra, near Antofagasta in northern Chile since 1993. From an initial operation based on Reverb smelting and Peirce-Smith, converting, the plant was expanded from 90 000 t/y to 160 000 t/y copper production in early 1997, by conversion to oxy-fuel smelting and use of concentrate injection on Converters. As part of this expansion a novel reverb gas cooling and cleaning system was developed and designed by Kilborn SNC-Lavalin Europe, the London, UK-based mining and metals; Office of Canada's SNC-Lavalin group. The reverb gas cooler needed to satisfy several very specific requirements including low cost, flexibility, robustness and simplicity of operation. Of particular importance was the requirement to cool and clean the ,oxy-fuel reverb gases and render them suitable for subsequent treatment in a conventional sulphuric acid plant. It was also important to avoid accretion or dust handling problems. This paper describes the key design features and subsequent successful installation, commissioning and operation of the unit.

Jan 1, 1998

By Zhang Y. D, Zhang R. X

A new decision-making approach of artificial neural network system with hierarchic structure is presented. The fundamentals of network topology, node functions and network training are introduced. A neural network system with hierarchic struct

Jan 1, 1998

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998