Search Documents

By M. Soltanieh

The liquidus surface? and tie-lines in the nickel-cobalt-sulphur ternary system have been determined between 1<273-1573 K. The experiments were conducted by equlibrating the liquid sulphide with the metallic alloy phase. The liquid sulphide phase was sampled and chemically analyzed. The alloy was analyzed by electrol} microprobe. Combining the present results with the.avai1abl~ literature data, the thermodynamic properties of this system were calculated.

Jan 1, 1998

The traditional concept of optimum drill and blast is that it is achieved when ore is produced at the lowest unit cost and, because of the complexities of most mining operations, represents a band which extends either side of an overall cost m

Jan 1, 1998

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

The evolution of the Oaky Creek mining complex provides a good example of the mining cycle in practice. Oaky Creek has been innovative in its choice of mining methods, with virtually the full range of coal mining methods having been used as workings have progressed down dip. The history of the mine is traced through its development (and ownership changes), progressive selection of mining methods as depths of cover to seams being mined have increased, and rehabilitation. This allows the different mining methods to be described and illustrates the concept of æwall-to-wall miningÆ.

Jan 1, 1998

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By S Z. Petho

The South Deep surface shaft system is being sunk to a final depth of 2750 m below surface and on completion will be the deepest single drop shaft in the world. The shafts will intersect the target reef horizon at 2650 m below surface. In order to negate the requirement for a shaft pillar, which would be extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This will limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will be stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill. Results from the numerical modelling exercises show good correlation with measured data. This indicates that a high degree of confidence can be placed in the model input parameters and consequently in the design of the shafts to ensure their long-term stability.

Jan 1, 1998

Ore petrology will fundamentally determine the types of metallurgical processes employed for ore treatment, their operational efficiency and the nature of processing problems encountered. It is therefore paramount that the petrological charact

Jan 1, 1998

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By R. J. Labine, D. I. Brisbin, R. Roussain, P. R. Coad

"Abstract - The Owl Creek Mine is located near the west end of the Neo-archean Abitibi greenstone belt, 17 km northeast of Timmins, Ontario, and 4 km north of the Destor Porcupine fault. Gold occurs in epigenetic quartz veins and their pyritic wallrocks in two zones within a package of east striking, steeply north dipping, volcanic and sedimentary rocks. At the West Zone, 1 729 603 t of ore with a grade of 4.83 g/t Au (268 587 troy oz.) were produced from an open pit centered on a wedgeshaped unit of Tisdale Group basalt that occurs between two overturned, south facing units of Porcupine Group graywacke and argillite. Basalt/graywacke contacts are locally marked by graphiticcarbonaceous argillite, strike-parallel faults and massive quartz veins.Deformed quartz+/-ankerite veins occur along the graphitic sedimentary/volcanic contacts and in gently to moderately dipping fractures in basalts, and, to a lesser extent, in graywackes. Veins also occur sub-parallel to steeply dipping 070° foliation. Altered host basalts are composed of iron carbonate, sericite, quartz, carbon, chlorite and disseminated pyrite. Gold occurs as inclusions in pyrite, and less commonly as free gold in fractures and along graphite-quartz grain boundaries in quartz veins. Fractures preferentially developed in more competent basalts during pre- to syn-ore deformation are interpreted to have provided the permeability required for emplacement of mineralized quartz veins. Carbonaceous basalt/graywacke contacts further enhanced gold deposition by acting as chemical traps. The interaction of hydrothermal fluids with these carbonaceous sedimentary rocks led to the characteristic local darkening of host basalts due to carbon impregnation and chlorite development."

Jan 1, 1998

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By Wang J, Ma Y, Jia H

The Hedong Gold Mine is located in the Yan(ai area, tihandong hroo%ill, e. China. It is an underground mine with an annual gold output of some 700 0(H) grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called &apos;sublevel open and fill stoping method&apos; in the mine. Experience to-date is that new mining method is Satisfactory.

Jan 1, 1998

By Gervais Soucy

During mineral and industrial processing, contaminated wastewater can be generated such as cyanide liquors (free species or in complex form). This paper presents the treatment of cyanide solution derived from the aluminum industry, by direct contact of the solution with thermal plasma in a novel reactor. The reacation energy is provided by a plasma submerged in solution which allows direct contact between the plasma and the solution to be treated. The scope of this&apos; study was to determine the feasibility of treating free and complex cyanides in solution through mini-pilot scale operations. An innovative reactor was designed and fabricated to provide stable: process operating conditions. Many parameters were studied. These experiments permitted the evaluation of the kinetics of complex cyanides decomposition under thermal plasma conditions. At atmospheric pressure (temperature about 100°C), the rate of cyanide decomposition by thermal plasma was 12 times greater than that of thermal hydrolysis in a plug flow reactor et the same temperature. The improvements in the decomposition rates are attributed to high thermal gradients at the plasma liquid interface and photocatalysis induced by the plasma UV radiation.

Jan 1, 1998

By Y. M. Jiang, D. W. Park

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1998

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI&apos;s threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By V. J. Matta, A. A. Pincheira, I. A. Reghezza, Ch. J. Vergara

The growth of solvent extraction in Chile has been astonishing during the last years and has been established as a very successful technology. However, there are still limitations that must be improved, mainly, the problem of carry over from one phase to the other and the losses of organic reagent associated with the crud formation. These are problems that our company has been taking care, solving them with high efficiency and low costs, allowing important increases in the copper output of our plants and capital savings by means of the optimization of the use of nonproductive units in the SX plants.

Jan 1, 1998

By F. F. Peng, D. C. Yang, G. Yanief, E. H. Cho

This study deals with carrier flotation of cerium dioxide, a surrogate of plutonium oxide, which is the major contaminant at the Nevada Test Site (NTS). The objective of this study was to determine the feasibility of using carrier flotation for remediation of the site. In this study, a - 200-mesh fraction of pure cerium dioxide was used. Oleic acid was used as the collector, while calcium carbonate was used as the carrier. Mechanical-cell tests were conducted to float the surrogate from a mixture containing uncontaminated NTS soil, both in the absence and presence of the carrier. It was found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34% to 65% by adding only 0.5% calcium carbonate (-150 mesh). The recovery further increased to 95% by adding 10% calcium carbonate. The flotation method utilizing a carrier of calcium carbonate seems to have a high potential for the remediation of the soil contaminated with radionuclides at the NTS.

Jan 1, 1998