Search Documents

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By K. Biswas, H. C. Lee, S. J. Jung

Ore passes are circular openings excavated in rock for in-mine gravity-transportation of ore. It is a very important component of the overall load-haul system of an underground mine. The function of an ore pass is two-fold: first, gravity-transportation of ore from the extraction level to the haulage level and second, the loading operation at the haulage level utilizing the gate assembly. In reality, like any other system component, an ore pass breaks down either due to a hang-up within the ore pass or due to a failure in the gate structure. The failure of the gate assembly may be attributed to a greater extent to the impact load as experienced by the components of a gate structure as a result of the direct impacts of the rock fragments and to a lesser extent to the static or 'dead weight' loads of the accumulated materials in the ore pass. This paper uses simulations in Working Model® as an aid to investigate the effect of both the impact and static loading on the gate assembly and on the inner-walls of the ore pass. The paper also investigates the impact of ore pass inclination and the presence or absence of dogleg on the static and impact loading of the same.

Jan 1, 2002

By M Boyd

The University of Wollongong was named University of the Year 2000, for its work in preparing students for the e-world. Computer facilitated learning is being introduced into subjects throughout the engineering course. First year mining engineering students are introduced to computers, e-communication, using the UniversityÆs web based information system, and web based subject delivery. Mining engineering students in the mid-years of the course use programming languages and numerical computation software such as MATLAB, while students in the final years use a range of commercially available professional engineering software such as TALPAC. Most of these subjects are offered as part of the UniversityÆs Learning Online program, co-ordinated by its Centre for Educational Development and Interactive Resources (CEDIR). Learning Online subjects are delivered using the Web Course Tools (WebCT) environment. WebCT allows all resources to be accessed through the web, allows email communication between lecturer and student, and allows discussion groups for the exchange of ideas. Students can submit their assignments through WebCT and receive immediate feedback. This paper describes how WebCT has been used to deliver a first year engineering computing subject, mid-year numerical computation subjects, a mining economics subject and mine planning subjects.

Jan 1, 2002

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By Rossen Halatchev

The production sequence optimization of open pit mine is a procedure that reflects the exploitation conditions over life of mine. These conditions are determined by the geological characteristics of the deposit, requirements of the mining and processing technologies and economic parameters of the exploitation. From a technological point of view the production sequence optimization deals with two aspects - spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the problem. This paper treats the time aspect of the production sequence optimization. This aspect is revealed in the context of the problem of the working zone formation of the open pit mine in time. The problem formulation places an accent on the determination of the theoretically possible time distribution of the waste and ore quantities of each bench of the open pit mine. A mathematical solution to the problem has been developed based on combinatorial analysis. The solution provides a multi-variant investigation of the production sequencing with the use of an optimization model developed as a linear programming formulation. The model objective function uses the Net Present Value as a criterion for assessing the effectiveness of production sequencing. A case study is provided for the conditions of Assarel copper open pit mine (Bulgaria) to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the mining factor.

Jan 1, 2002

By P Allum

This paper presents a case study to reduce the operational cost on the secondary ball mill circuit in the Lead/Zinc Concentrator at Mount Isa Mines. The circuit includes two five-metre diameter ball mills each closed with a cluster of ten 15-inch cyclones. The operating cost for both ball mills is about six million Australian dollars per annum.The concentrator achieves 75 per cent of the plant design capacity with one ball mill operating, but will have to use two ball mills when 100 per cent plant capacity is required. The optimisation study on the circuit identified a new flowsheet that enabled the concentrator to reach 100 per cent of the capacity by using one of the two secondary ball mills. The success of the project utilised the existing equipment rationally and saved the operational cost for one ball mill at full concentrator capacity. A further simplified secondary circuit is proposed using the IsaMill for the secondary grinding duty. Performance of the IsaMill circuit and the potential cost savings are predicted.

Jan 1, 2002

By Sang-Beom Lee

For thermodynamic prediction, the deoxidation equilibrium of aluminum in Fe-36%Ni alloy was studied with a cold crucible under Ar gas atmosphere at 1773K. For the deoxidation reaction in liquid Fe-36%Ni base, i.e.: A12O3(s) = 2A1 + 3O The interaction parameters and the equilibrium constant between aluminum and oxygen in liquid Fe-36%Ni alloy are given in the following: eo Al = -3.8, roA1=0.9, eAl° = -6.4, rAl° = 700, rAIAIo = 3.1, roA1o = 833 within the composition range of [Al] < 1 mass%. The temperature dependence of the equilibrium constant was obtained in the range of 1773K < T < 1973K by using reported data and present results as follows: log KAo= 0.58-24463.7 / T The deoxidation equilibrium with aluminum in Fe-36%Ni could be thermodynamically well described in the range up [Al] < 1 mass% with first and second order interaction parameters as well as the equilibrium constant determined in this study.

Jan 1, 2002

This article updates the status of fatalities occurring in both coal and metal/nonmetal mines from January through December of 2001. Based on preliminary accident reports, as of December 31, 2001, seventy-two fatalities have occurred at coal and metal/ nonmetal mining operations. During this period, forty-two fatalities occurred at coal operations and thirty fatalities occurred at metal/nonmetal operations. Ignition or explosion of gas or dust and fall of roof were the most frequent accident classifications in coal and powered haulage fatalities were the most frequent accident classification in metal/nonmetal.

Jan 1, 2002

By Yuusaku Tominaga, Sukumar Bandopadhyay

A power-series trend curve of elapsed time was estimated by using time series data of measured concentrations of carbon monoxide in the Taiheiyo coal mine, Hokkaido, Japan. The difference between the moving average concentration data and the estimated data from the trend curve showed linear correlation when plotted on a normal probability paper and a correlation coefficient value of 0.99. It is concluded that the estimate of carbon monoxide concentration using moving average values of concentrations compares very well with the results obtained from the trend curve within the three-sigma (standard deviation) range of the distribution. Thus, it is believed the results can be used to monitor and detect abnormal ventilation conditions in a ventilation network such as the occurrence of spontaneous combustion at an early stage.

Jan 1, 2002

By Hunsoo Choi

Internal textures of manganese nodules from Clarion-Clipperton zone of northeastern Pacific Ocean are classified into five textural zones: columnar-textured layered zone, cuspate-textured layered zone, cuspate-textured massive zone, cuspate-textured porous zone and massive- textured massive zone. Vernadite is the main constituent mineral in the columnar- and cuspate-textured layered zone. Buserite sometimes occurs in the cuspate-textured layered zone. The cuspate-textured massive zone is mainly composed of buserite. Todorokite is also associated with buserite in the massive-textured porous zone, where cuspates and globes are partially replaced by massive texture. In the massive-textured massive zone, todorokite, buserite and birnessite occur together. The analyzed elements of all zones are also classified into four elemental groups by the cluster analysis of correlation coefficients: Mn group, Cu-Ni-Mg group, Fe group and Si group. Mn group consists of Mn and K. Cu-Ni-Mg group consists of Cu, Ni, Zn, Mg and/or Ca, Na. Fe group consists of Fe, Co, Ti and/or Ca, P. Si group consists of Si and Al. Each textural zone is composed of three or four elemental groups. These four elemental groups are correlated with mineral composition, such as, Mn group with todorokite, Cu-Ni-Mg group with buserite, Fe group with Co-bearing iron-oxyhydroxide minerals, and Si group with silicates.

Jan 1, 2002

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002

By Wanchai Teparaksa

Pile deviation generally can happen after installation of driven pile particularly in soft soil layers. In this case study, all 242 diameter 0.8 m spun piles were deviated from 20 to 820 mm. The large deviation was caused by lateral soil movement in the top very soft clay layer of thickness about 23 m. This very soft marine clay is very sensitive and anisotropic having high water contents of over 120% and low undrained shear strength of 5-10 kN/m2. The remedial works were carried out based on theory of load transfer and soil-structure interaction. All deviated piles were rectified and used as the foundation piles with strictly controlled pile load tests. The construction of a nine-storey building was successfully completed founded on the rectified piles and it has been opened for the service for over two years.

Jan 1, 2002

By Matthew E. Eisenmann, Gerald H. Luttrell

Performance data from phosphate plants are often untrustworthy because of difficulties associated with highly variable feeds and unstable equipment operation. In some cases, this problem is further compounded by improper sampling procedures and unreliable laboratory analyses. Questionable data often lead to misleading conclusions that result in lost productivity and profits. Data reliability may be checked using mass balances, but the mathematics associated with this procedure can be overwhelming when multiple data sets or complex circuits are evaluated. To overcome this problem, a simple spreadsheet-based mass balance program has been developed specifically for plant operators. To use this program, operators simply enter a description of their circuit and input the assay values (e.g., % BPL, % Insol, etc.) for each stream. The program then generates the best estimates of the assay values and flags values that may be unreliable. The spreadsheet is specifically designed to be easy to use and requires no knowledge of statistics or programming. This manuscript reviews the mass balance problem and describes how spreadsheet programs can be used to evaluate plant data. An example problem involving the analysis of data around a two-stage phosphate flotation circuit is presented.

Jan 1, 2002

By Kyle L. Brennan, Scott Maybrier, Gang Chen, Scott Huang

Data from about 3200 drill holes in the offshore area at Nome, Alaska was digitized and processed. Most drill hole files have associated lithology, gold value, and blow count descriptions for each drill hole. The gold intensity was used to present the potential gold resource in the study area on the world wide web. A web page was created that gives background information on the project, descriptions about the Nome area, maps of the claim blocks that include all the normalized slices of gold deposits, and links to other relevant sites on the web. The site is located at http://mineral.uafsme.alaska.edu/nomeproject/nomehome.htm.

Jan 1, 2002

By Tony P. Suckling

This paper presents a case study of a piling contract undertaken at Keble College in Oxford in the year 2001. Unusually, and for the first time in the United Kingdom, piles were successfully constructed containing a network of plastic pipes, which are subsequently to be connected to the heating and cooling system for the new building. The pipes cast in the piles facilitate the transfer and storage of geothermal energy between the structure and the underlying ground mass, allowing the new building to be both heated in winter and cooled in summer economically and in an environmentally friendly way. The philosophy of the geothermal pile technology is presented, together with the modified pile construction techniques employed on the site.

Jan 1, 2002

By Klaus Böde

Within the national and international strategy of the German based construction company HOCHTIEF, the majority of its business units is equipped with the comprehensive software package ARISTOTELES. This software is a powerful business information system for all accounting and controlling related processes in medium-sized and large construction and other related companies. Due to the complexity of the software, time constraints, and limited financial resources an implementation of this software package requires thorough project management. In this paper the relevant elements of project management are outlined based on practical experiences gained during this international IT - implementation project. Special emphasis is directed to the identification and management of potential risks. In this case particular acknowledgement was given to the multinational nature of the project and modernization of the business. This includes thorough reorganization of the company, significant changes of job requirements, and substantial trainings for its employees. At the same time key success factors like knowledge transfer, adoption of Czech legal requirements, commitment of management, networked thinking, and integrated project planning come into play. The costs for implementation had to be carefully evaluated because the software was implemented in a country with a considerably low cost I price level. All these impacts to the business had to be managed within the scope of transformation of business and political environment from socialist to market driven economy.

Jan 1, 2002

By R. Laplante, P. Radziszewski, P. De Ciccio

"Predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case. Wear conditions vary with geological formations and compositions. The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American drilling campaigns. Simulation results allow the definition of simple graphical tools that permit the estimation of the potential drill depth remaining on a given drill rod string. IntroductionWear, in many industrial processes, is an undesired phenomenon for which enormous efforts are made to control, if not eliminate. However, wear, in many other cases, is an intrinsic phenomenon of the given process. In such cases, predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case where abrasive conditions vary with geological formations and compositions.A number of studies have been published on drill rod wear especially with regards to the petroleum industry over the last thirty years (Lewis, 1968; Rollins, 1968; Smith, 1978; White 1978; Rowe and Wilson, 1981; Cheng, 1982; Eustes, 1986; Dudman et al., 1989; Besaisow et al., 1990). Of these, most studies covered management techniques (Rollins, 1968; Smith, 1978; White, 1978; Rowe and Wilson, 1981; Besaisow et al., 1990) and some described case histories (Cheng, 1982; Eustes, 1986; Dudman et al., 1989). However, little (Lewis, 1968) was presented that could aid in predicting wear in the particular case of diamond drilling in the metal mining industry.The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate diamond drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American diamond drilling campaigns."

Jan 1, 2002

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By Cameron Harris

With the consolidation of the copper industry in the second half of the 20th century resulting in fewer plants treating ever increasing quantities and qualities of feed, the enormous flexibility of the Noranda Process gives it significant advantages over many competing technologies for the production of matte. Toll smelting, recycling, and secondaries treatment will become the cornerstone of profitable operations for all but the lucky few who have large captive mines associated with the smelter. Consequently, the ability to respond to changing market conditions without significant metallurgical or operational upsets will be of considerable commercial advantage. The inherent stability of this bath-smelting process leads to tight matte grade control, while the bath turbulence leads to rapid consumption of feeds with widely varying physical characteristics. Low capital and operating costs combined with a layout suitable for retrofit into existing converter aisles makes it a sensible choice for parts of the world still experiencing the aforementioned consolidation, which is essentially complete in fully developed economies such as the United States of America and the European Union. This paper will discuss features of the Noranda process compared with other technologies and its place in the future global copper production industry, which is set to become increasingly competitive and aggressive.

Jan 1, 2002