Search Documents

By W. A. Heitbrink, M. Schmitz, J. A. Organiscak, A. B. Cecala, E. Ahrenholtz

Mobile excavation equipment operators at surface mines generally have the highest exposure to airborne respirable silica dust. Operator cabs on newer equipment are usually enclosed and equipped with heating and air conditioning systems. Many newer cabs are also equipped with air filtration systems. However, some newer cabs and many older cabs have either inefficient or no air filtration systems. The U. S. surface mining industry is still populated with older equipment and many of these have cabs that provide little or no respirable silica dust protection. Collaborative field studies were conducted as part of a partnership involving NIOSH, Clean Air Filter®, Red Dot, MSHA, and several mine operators to demonstrate that effective dust protection can be provided by these cabs at a nominal cost to mine operators. This effort encompassed adding an external make-up air fan and filter system to a retrofitted roof-mounted heating and air conditioning system in three older equipment cabs, and attempting to seal the cab enclosures to achieve interior cab pressurization. Abetter than 90 percent dust reduction was measured inside two of the three enclosed equipment cabs. It was possible to achieve positive cab pressurization inside these two cabs. A less significant dust reduction was measured inside the third cab, where positive pressurization was not achieved. These field studies demonstrate the key elements needed to improve enclosed cab dust protection in a cost-effective manner.

Jan 1, 2003

By Vasily V. Lodeischikov, Adolf F. Panchenko, Olga D. Khmelnitskaya, Vladimir E. Dementyev

Pilot plant tests of underground gold leaching from Maminskoye deposit oxide ores at a grade of 0,7 g/t Au were carried out. The underground leaching flow sheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution on active carbon, carbon concentrate ashing and calcine melting to produce high grade gold concentrate. The underground leaching system throughput was 15 m3 of solution per hour. Gold concentration in pregnant solutions was 0.12-0.13 mg/l. Gold recovery from solutions into carbon was in the range of 63-84%. It was demonstrated that the low Au recovery in the adsorption cycle was due to the presence in pregnant solutions of "active" chlorine, which destroys active carbon and causes a sharp decrease of the carbon loading capacity for gold. To improve the adsorption indices, previously dechlorinated pregnant solutions using bituminous coal or Na2S2O3, is recommended. Ion exchange process was tested as an alternative for gold extraction from dechlorinated solutions. In the testwork period, 4.4 kg of gold were produced with a chlorine consumption of 3.5 kg per 1 g of gold. During the tests a program of environmental protection measures was completed to provide the necessary safety precautions of the underground leaching works.

Jan 1, 2003

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

Politicians and economists talk glibly about the so-called knowledge revolution. The reality is that knowledge is fundamental to economic progress. Consequently there have been many technological revolutions. The global impacts of the invention of the steam engine and the development of the frozen meat industry are well known. Another less publicised technological advance occurred in Central Otago late in the nineteenth century. This was the adaptation of the bucketladder dredge to the mining of placer deposits. A product of over 30 years experimentation and innovation, New Zealand dredging technology was taken to the Risdon Iron and Locomotive Works, San Francisco by R H Postlethwaite, a Dunedin based mining engineer. New Zealand-style dredges built by Risdon operated successfully in California, Alaska and the Yukon. Californian engineers assimilated the best features of the New Zealand dredges with American (Bucyrus) designs to produce a standard for the worldwide placer mining industry.

Jan 1, 2003

By N Meyer

This paper presents a research project referring to the stability of submerged walls of open pit mines and the actual state of development. Obviously the slope stability analysis is always a rather complex problem, because it is difficult to reduce the problem to a design scheme and to define the available in situ soil strength. Especially the design of submerged slopes represents a problem. The state-of-the-art slope stability analysis is based on a simplified modelling of slope failure and soil behaviour and with this predicted stable slope inclinations of sand slopes below water-table are less then half the angle of internal friction. Slope angles calculated like that canÆt satisfy the mining companies. One of the problems that have to be solved is the reliable determination of the long-term stability of non-cohesive, submerged slopes, which is not only dependant on geotechnical and hydrogeological parameters of the subsoil, but is also significantly influenced by how the slopes are made. The research project points at the relations between mining and geotechnical engineering with the main aim to find a more suitable stability analysis which takes both soil behaviour and mining influences into account.

Jan 1, 2003

By Ponisseril Somasundaran, H-L. Chen, University of Athens, D. R. Nagaraj, Zhonghua Pan, Jing Wang

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By M. Pötsch, M. Blümel, E. A. Button

ABSTRACT: Stiffness controlled test procedures performed with servo-controlled shear systems are the most versatile for simulating the wide range of boundary conditions expected in nature. Examples of a function controlled procedure in addition to dilatation controlled procedures are discussed for different characteristic behaviours. ZUSAMMENFASSUNG: Steifigkeitskontrollierte Scherversuche mit servohydraulischer Steuerung eignen sich gut unterschiedliche Bettungen, wie auch in der Natur vorkommen, zu simulieren. Beispiele für spezielle Steuerungsfunktionen und dilatationsgesteuerte Prozeduren mit verschiedenen charakteristischen Eigenschaften werden diskutiert. RESUMÉ: La rigidité a commandé des méthodes d'essai exécutées avec les systèmes asservis de cisaillement sont la plus souple pour simuler l'éventail d'états de frontière prévus en nature. Des exemples d'un procédé commandé par fonction en plus des procédures commandées par dilatation sont discutés pour différents comportements caractéristiques.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of eomposition at the temperatures from 850K to 1050K. An alloy was vaeuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

By D Craw

Previous studies of alluvial gold in Otago and Southland placer deposits have suggested a gold-mercury association for some deposits derived from Caples Terrane schist, whereas alluvial deposits on Torlesse Terrane basement typically have no mercury. A regional study of gold from Otago Schist vein deposits from both Caples and Torlesse Terranes has revealed the presence of both Au-Ag and Au-Ag-Hg alloys in both terranes. Au-Ag alloy (3 - 4 wt per cent Ag) is typical for gold found in most Torlesse vein deposits, and Au-Ag-Hg alloy (3 - 8 wt per cent Ag, 2 - 8 wt per cent Hg) is found in many Caples vein deposits. Au-Ag-Hg alloys are not exclusive to the Caples Terrane, however, as Au-Ag-Hg alloys with up to 4 wt per cent Hg are found in vein material from the Torlesse-hosted, HydeMacraes Shear Zone. In addition, not all Caples-hosted deposits have a gold-mercury association; gold grains from the Carrick and Invincible gold fields have no detectable mercury. The present study characterises gold compositions from various hard-rock vein deposits and has potential for determining placer-source relationships.

Jan 1, 2003

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"The effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases.Electrokinetic methods were used to elucidate the mechanism of surfactants adsorption and to correlate these findings with the optimum flotation conditions. The polymeric surfactants would reduce the negative values of zeta potential of quartz while the reverse is true for feldspar. After treatment of microcline with HCl, its electrokinetic behavior in the presence of Tritons X surfactants became similar to that of quartz.The obtained results would suggest that separation of quartz from feldspar using nonionic surfactants of octylphenoletoxylated alcohols having shorter oxyethylenic chain length at low pH could be achieved"

Jan 1, 2003

By N Currey, G W. Wilson, P Ritchie

Kidston Gold Mine in Queensland, Australia has a 310 ha tailings impoundment that has undergone final closure rehabilitation. Kidston Gold Mine evaluated their closure options for this low acid generating tailings impoundment, and due to a lack of cover soils and the cost of importing material, the mine decided to investigate the possibility of direct vegetation onto the tailings impoundment surface. The mine subsequently embarked upon a well planned and detailed research program to determine the feasibility and sustainability of this closure option. The research program included vegetation trials, toxicology studies for metal uptake by vegetation, as well as a comprehensive closure water balance model for the tailings impoundment complex. This paper describes the results of the long-term closure water balance for the tailings impoundment complex for the pre-closure state of the impoundment, as well as predictions towards the impoundment performance once final rehabilitation of the tailings impoundment complex has been achieved. The water balance presented is unique in that it is founded on unsaturated flow principles and accounts in full the impacts of the surface flux boundary conditions. This novel approach enables the prediction of actual infiltration rates into the tailings impoundment surface, which in turn allows for the calculation of how much seepage will exit from the tailings dam toe drains.

Jan 1, 2003

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Ian S. Thompson

"Exploration properties form a continuum from grass roots to those with favourable geology, geochemical and/or geophysical anomalies, mineralization, showings (prospects), and finally to those with defined mineral deposits. Often properties exhibit a composite of these categories.The most problematic to value are properties or deposits that are not economically exploitable at the time of the valuation, due to a lack of exploration, insufficient grade or tonnage, poor mining conditions, or the imposition of socioeconomic, environmental, or legal constraints.Various acceptable methods of valuing the range of all such mineral properties or deposits are reviewed. Some inappropriate methods are also discussed.BIOGRAPHYIan S. Thompson is President and Principal of Derry, Michener, Booth & Wahl Consultants Ltd. (DMBW), an independent consulting practice, specializing in exploration, ore reserve estimations, engineering and valuations of mineral properties.Mr. Thompson is a graduate in Honours Geological Sciences from the University of Toronto with over 35 years Canadian and International experience in mineral exploration and development, including the discovery of base metal. gold and uranium deposits.DMBW is affiliated with DMBW, Inc. in Colorado, and works with independent engineering and financial groups in North America, Europe, Australia and Africa.Mr. Thompson is a national member of CIM; the Associations of Professional Engineers of Ontario and British Columbia; The Geological Association of Canada; The Society of Economic Geologists; The Prospectors and Developers Association of Canada and the BC and Yukon Chamber of Mines.INTRODUCTIONThis paper is presented in response to the request of the Mineral Economics Society of the Canadian Institute of Mining and Metallurgy for a Review of Approaches to Valuation of Mineral Properties, as recommended by the TSE/OSC Mining Standards Task Force.Exploration properties with undeveloped mineral resources range from grassroots acreage without exploration history, to those containing mineralization (or a mineral resource) that is insufficiently explored, to well explored deposits which lack either continuity, or sufficient grade/tonnage, or have poor mineability or metallurgy, such that they are not currently exploitable at the time of the valuation. This does not imply that they do not have value."

Jan 1, 2003

By A. Karadogan, G. Tuncer, A. Kahriman, S. Gorgun

This paper presents the results of ground vibration measurements induced by blasting operations at five different sites located close to the residential areas. Within the scope of this study, ground vibration components were measured for all blast events over a long period of time in order to predict peak particle velocity and determine the slope of the attenuation curve for five sites. During the study, while the parameters of scaled distance were being recorded carefully, suitable monitors for all blast events of five blasting sites measured the ground vibration components. At the end of evaluation of the data pairs, an empirical relation, which gives an average line at 95% confidence level, and upper bound 95% prediction line with a good correlation coefficient was established and suggested for each site

Jan 1, 2003

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By D. Sotiropoulos

In the recent years, the mining sector is looking for specific indices, taking into account economic, environmental and social criteria, in order to meet the sustainable development requirements. In the present study traditional and environmental sustainable indices used in the Agios Dimitrios Power Plant, Northern Greece, are compared to those of ESKOM Company, South Africa, taken as reference. These indices are referred to, a) the solid fuels consumption, such as lignite, and, b) the emissions to the atmosphere, such as SO2, NO2 and dust. Last five years data show a remarkable improvement of all indices in the Agios Dimitrios Power Plant. Although the lignite used in this Power Plant is by far of poorer quality than that used by ESKOM - net calorific value 1272 and 4638 kcal/kg, respectively - dust emissions in both Power Plants are similar (52 and 31 g/kWh, respectively). The SO2 and NO2 emissions are very low in Agios Dimitrios compared to those of South Africa, respectively 1.92 and 7.91, and 1.74 and 3.61 g/kWh. This is mainly due to natural desulfurization (by the lignite?s calcium content) and the low NOx burners.

Jan 1, 2003

By C Gypton

This paper gives some insights into what to look for when reviewing feasibility studies. The review by a third party is an important element of the risk management process and may be the last remaining opportunity to uncover errors, or identify and reduce project risks on paper before they are converted to financial disappointments, steel and concrete monuments to process failures or cost overruns. The mining industry has had a spotty record in the area of estimating initial capital costs and operational performance, even though the standard of feasibility studies is generally acknowledged to have improved in the last decades. Third party reviews rarely have the luxury of enough time and unlimited funds, so where should the reviewers focus their efforts to be most effective? Assuming that the project already apparently meets investment criteria, the authors suggest where and how to look among fundamental project parameters for signs that serious flaws exist that have the potential to become project killers. We also give advice on how to review cost estimates without becoming lost in the details. The paper is supported with numerous actual examples.

Jan 1, 2003