Search Documents

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By Jose Bengoa

Low metal prices and environmental restrictions are always a challenge for copper smelters operation and its productivity. Thus, in order to reduce production costs and control gas emissions, improvements of the Teniente Converter (CT) operation were made at 110 Smelter Plant of Southern Peru Copper Co" 110, Peru, and the main objective was to increase its capacity for smelting copper concentrates without affecting normal operation, The present work eorresponds to a recent study conducted during the normal industrial operation of the Teniente Converter in this plant and, it shows the effect of increasing air oxygen enrichment from 28 to 34% on its productivity. The results show an increasing of concentrate smelting rate from 800 to 1370 tpd and hence a notorious improving in copper production, and practically no effect on the refractory consumption. The increment of the concentrate throughput, increases also the SO2 concentration and the sulfuric acid production, showing the effort done by this operation in order to accomplish the environmental Peruvian regulation,

Jan 1, 2003

By I. M. Santos Moraes

The control of minor impurities (mainly As, Sb and Bi) in copper refineries has been a great challenge. Caraiba Metais' copper refinery produces a very high quality copper, registered in LME as grade A, and recognized as amongst the top ten in the copper world. At Caraiba's Tankhouse Bi and Sb are controlled by means of electrolyte bleed-stream removal after partial decopperizing in a set of electro-winning cells (liberators). Another way of reducing the Sb and Bi content in the electrolyte is by means of the arsenate precipitation chemistry. It is well known that the use of high arsenic concentrations in copper refinery electrolyte has the advantage of causing most of the bismuth and antimony to report in the anode slimes. However, the use of such mechanism of control may contribute to other undesired problems such as antimony and bismuth precipitation in the bulk of the electrolyte, what may cause severe contamination problems. This paper describes a period when some cathode contamination with Sb occurred at Caraiba Metais' Copper Refinery. It also presents an analysis of several process parameters related to the problem, the possible causes for the contaminations as well as the actions taken to correct the problem.

Jan 1, 2007

By M Csar

The Nicolsons Find gold project is located 35 km southwest of Halls Creek in the east Kimberley. It was discovered in the late 1980s by John Nicolson and Stuart Skoglund, when high grade gold mineralisation within outcropping gossanous quartz reefs was found. The area has produced a modest 28 150 ounces of gold over two brief mining periods in 1996 and 2002 - 2003. Indicated and inferred resources as of September 2011 stand at 1 384 000 t at 5.58 g/t Au for 248 500 ounces of gold.The project is situated within the Halls Creek Orogen. Principal host units are metasediments and volcaniclastic sediments of the Koongie Park Formation. Minor mafic units are also recognised. Immediately east of these units, emplacement of the loadstone granite is believed to have provided the structural setting for the later gold mineralising event.Mineralisation is hosted within a broad, brittle-ductile arcuate shear zone about the western contact of the Loadstone granite. In the Nicolsons Find area, the shear zone strikes north-northeast and within the shear zone, gold is hosted in a series of narrow, quartz rich veins up to 200 m in strike length, plunging moderately to the north-northeast. To date, mineralisation has been drilled to a depth of 360 m below the surface. The veins are stepped or en-echelon in nature with low gold values towards the quartz vein limits where compression is inferred and higher grades present in the dilational body of the quartz veins. Gold is fine grained and can be present with or without associated sulfides. Sulfides are generally minor and consist mainly of arsenopyrite with traces of chalcopyrite, pyrite and sphalerite. Where present, sulfides are generally indicative of higher gold values.CITATION:Csar, M, 2012. NicolsonÆs Find gold project, East Kimberley, Western Australia, in Proceedings Narrow Vein Mining 2012 , pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By Toivo Toivanen

The paper begins with a brief history of the nickel industry in Finland, and then deals with the introduction of the flash smelting process. The main part of the paper is devoted to nickel refining, which is studied under four main headings -grinding, leaching, electrolyte precipitation, and nickel electrowinning. Flowsheets are illustrated, and the equipment used is described. Analyses of the material in the various stages, from concentrate to high-grade nickel matte, are also presented. N ICKEL made its appearance in the Finnish mining industry forty years ago, when a nickel deposit was discovered at Petsamo in Lapland. Mond Nickel Co. received the concession for this deposit from the Finnish Government, and the Petsamon Nikkeli Company constructed a mine and a nickel smelter (1), the completion of which was prevented by the 1939 Winter War. The mine and smelter were, however, completed soon afterwards in spite of World War II,

Jan 1, 1964

In the future, Illawarra Coal, the primary metallurgical coal producer in the southern coal fields of New South Wales, will face many unique challenges not found in other coal or minerals production areas. To manage these challenges and determine the best strategy for the business, Illawarra Coal has adopted a systematic strategic planning process, which starts from the broadest possible options analysis and culminates in a ægo-forwardÆ operating case that individual mine sites use as the basis for short-term planning. This paper will discuss two major topics. Firstly an overview of the Illawarra Coal and BHP Billiton strategic planning processes. This will demonstrate the range of variables and inputs that are required for the planning process, and the system which is followed to evaluate different alternatives for the extraction of the resource. Secondly, having discussed the primary external and internal factors that must be accounted for in the planning process, and the main issues affecting the viability and likelihood of each alternative, the paper will discuss the particular challenges that Illawarra Coal will face in the coming decades. These challenges include: market and price uncertainty; managing impact on surface features, infrastructure and environment; community interaction; transport and logistics constraints; unknown mining environments; lack of geological knowledge; limited surface access for new mining domains; changing attitudes to longwall mining in the Illawarra; ageing workforce; and cost and overhead management. The paper intends to discuss how these issues impact the business currently and how they are incorporated into Life of Asset plans and overall corporate strategy for Illawarra Coal.

Jan 1, 2007

By R. F. Jones, N. E. Truitt, M. Prats

In most published discussions and theories of in situ combustion, the combustion fronts are assumed to be vertical. However, evidence from field tests leaves no doubt that combustion fronts often advance more rapidly along the top than near the bottom of a formation as a result of difference in density between injected air and formation liquids. The approximation proposed in this paper to determine the movement of the resultant tilted combustion surfaces states that the vertical rate of movement of combustion surfaces is proportional to the horizontal oxygen flux. Where self-ignition is possible, the proposed method demands that a secondary combustion surface exist around production wells which produce some oxygen. These secondary combustion surfaces may be formed long before the primary combustion surface can advance from injection to production wells. Heat liberated near production wells at these secondary combustion surfaces can contribute to an early increase in production rate. Results indicate that significant oil recoveries cannot be obtained from the usual flood patterns (five-spots, seven-spots, etc.) without producing large volumes of unused oxygen. Ideally, to increase oxygen- consumption efficiency, well patterns should allow oil production from a first line of production wells and gas production from more distant lines of producers. However, it may be desirable to produce some gas at all wells to support (and benefit from) active secondary combustion surfaces. Results indicate that the well spacing through which combustion can be advanced is larger than that predicted by other methods. A large number of production wells may still be desirable to take quick advantage of gravity drainage. From a comparison with results at South Belridge field, California, it appears that this method adequately describes oxygen concentration and temperature histories and combustion-front shapes. However, this method does not accurately locate the most advanced point of the combustion surface. There is some field evidence to substantiate the actual presence of secondary combustion surfaces at South Belridge. Use of the proposed method appears warranted at this time when lay-over of the combustion surface can be anticipated. INTRODUCTION The assumption of vertical combustion fronts has been embodied in all previous publicationsl-6 which use the movement of combustion fronts away from injection wells to determine the temperature and fluid distributions in the reservoir. The only paper concerned with a mathematical model of the combustion process in which a nonvertical combustion front is used was written by Gottfried.11 Actually, nonvertical combustion fronts have been observed in most in situ combustion field tests for which adequate data are available.7, 8, 6 In practice, the typical vertical extent of the burned zone decreases with distance from the injection well, and this burned zone is at or near the top of the sand body. In some cases, such as at South Belridge field near Taft, Calif., the combustion surface is almost horizontal over a very large area.8 Thus, for some years an obvious and serious gap has existed between theory (vertical fronts) and practice (tilted fronts). This is indicated in Fig. 1. Tilted combustion fronts such as observed at South Belridge8 sometimes result from the natural tendency of injected gases to rise to the top of an oil sand. An initially present gas cap, even if thin, would make apparent the effect of gravity segregation from the first, particularly since formations considered for in situ combustion field operations are generally selected for their

Jan 1, 1969

By Junwei Han, Wenhua Li, Wenqing Qin, Fen Jiao, Wei Liu, Jiaqi Xu

"A novel technology was developed to study the process of recycling copper from waste printed circuit boards (WPCBs), which are the main source of metal production in the next decades. The chemical compositions of the WPCBs were investigated. The results indicated that the PCB powder was mainly composed of copper (38.5 wt.%), iron, aluminum, and non-metallic materials. Copper is mainly in the form of Cu and is the most valuable metal for the recycle of WPCBs. The concentrated WPCBs powder, obtained by the mechanical process, were pressed as the anode, which was directly electrolyzed to produce copper. The effects of H2SO4 concentration, Cu2+ concentration, current density, pole pitch, and liquid-to-solid ratio on the voltage, current efficiency, and copper extraction were investigated. The results indicated that the optimum conditions were liquid-to-solid ratio of 30 mL/g, current density of 571 A/m2, sulfuric acid concentration of 180 g/L, 50 g/L of copper ion, polar distance of 3 cm. Under the conditions, a desired current efficiency could be achieved. Meanwhile, about 95.62% Cu was recovered from the WPCBs. The experimental studies also revealed that the purity of copper obtained at the highest current efficiency was higher to 99.98%. Produced copper sheet were characterized by X-ray diffraction (XRD). XRD analysis indicated that the copper was the main phase. INTRODUCTION With the rapid development of electronic industry, more and more waste electronic and electrical equipments (WEEE) are generated every year (Fogarasi et al., 2012; Liang et al., 2013). The production of printed circuit boards (PCBs) is the base of electronic industry, because it is the essential part of all electrical and electronic equipments (Schlummer et al., 2007). As a result, a considerable amount of waste PCBs containing plenty of heavy metals have to be treated. In general, PCBs contain about 28% metals that are abundant non-ferrous metals such as Cu, Pb, and Sn. Printed circuit boards can be considered as a secondary resource for recycling rather than wasting. The contents of gold and silver respectively reach 80 g/t and 3300 g/t, which are much higher than that of primary ores. Copper is the main metal of PCB and its content is as high as 26.8% ( Zhang et al., 2009)."

Jan 1, 2018

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By Thomas L. Watson

My thanks are due to Mr. Frank Firmstone, Easton, Pa., who has called my attention to the statement in my paper' that " Barite, fluorite and quartz, thougll not observed in the Tennessee area," ... as possibly misleading to the reader, if construed to mean that such a discovery had never been made. Mr. Firmstone is correct in assuming that this statement referred only to the study of the worked areas of the metallic ores, especially zinc, made in the course of the survey upon which my paper was based. The occurrence of barite and fluorite with lead-ores in Tennessee was reported by Prof. Safford? in 1869, and by Safford and Killebrew? in 1887, with the further statement that about 1,000,000 lb. of barite were annually mined in Greene, Washington and Jefferson counties, Tenn., and that considerable deposits occur also in McMinn, Smith and other counties. It is also noted that the barite " usually occurs in veins, associated with galena." The present worked areas of barite are, however, distinct barite propositions, without workable quantities of either lead or zinc, so far as mining operations have gone, and the areas are more or less removed from the present areas of zinc-ores. Mr. Firmstone informs me also that, in 1892, he observed, in the magnesian limestone at Watauga Point, in Carter county, on the left bank of the Watauga river, a little below the mouth of Buffalo creek, small quantities of galena and some fluorite.

Jan 1, 1907

By James E. Bell, Clyde B. White

"INTRODUCTION The Friedensville district was one of the most important zinc-producing areas in the United States from 1859 to 1893. The ore minerals near the surface were principally calamine and smithsonite, but with depth sphalerite was found in increasing proportions. The ore bodies of the district are reported to have been in chimneys, occurring in folded and faulted beds of Beekmantown limestone of Ordovician age.The Correll was one of five mines near Friedensyille that were exten¬sively exploited. The high-grade ore shoots were mined to a depth of several hundred feet, but it is believed that inability to compete with lower-cost production elsewhere, rather than exhaustion of the ore bodies, compelled the mines to close.There is no record to indicate that any attempt was made during the period of operation to explore for additional ore in the limestone beds down the dip below the mine workings. The possibility that exploration might reveal additional ore in the limestone beds below the known ore shoots led the Bureau of Mines to diamond-drill the Correll property between September 1943 and January 1944."

Jan 1, 1948

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

By G. S. Phipps, E. E. Schumacher, G. M. Bouton

THE seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort, Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedures were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called "wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united' are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I, The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. By going to an extreme and wiping off all the solder in excess. of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By Steven A. Fechner

In 1984 the Bureau of Mines cunducted mineral investigations of specific sites within the Yentna Mining District. One hundred eight placer and rock samples were taken. Reconnaissance placer samples were collected from drainages in the Talkeetna, Susitna, and Yentna River basins. The highest placer gold values were found in the historic placer gold producing creeks of the Cache-Peters Creek area. Samples taken from an outcrop in the Middle Fork of Iron Creek in the Talkeetna Mountains contained previously unreported high lead, zinc, and silver values.

Jan 1, 2011

By E. Kokinou

The main scope of the present study is to investigate the suitability and sensitivity of the magnetic susceptibility as a pollution monitoring tool in urban areas. For this purpose, a municipal park located in the centre of Chania city, which may be affected by traffic and domestic heating pollution, was selected as the study area. In the context of the present work, magnetic susceptibility measurements were conducted in two phases. Surface soil samples were collected in 2006 from the area under investigation and they were analyzed in order to estimate the spatial distribution of the magnetic susceptibility. One year later, mapping of the magnetic susceptibility has been contacted in situ using Bartington MS2D and MS2F sensors. Additionally, soil samples were collected from selected positions in order to compare the values of the magnetic susceptibility with that estimated in 2006 research. Both investigations indicate high values of the magnetic susceptibility around the park near the roads and in a small area inside the park where a café is located.

Jan 1, 2008

By Richard P. Rothwell

REVOLING slime-tables with stationary sprays and oscillating brushes have for many years been a favorite apparatus used for working slimes in German dressing-works, often displacing Rittinger tables and the many variations of Cornish buddles. The difficulty of building these tables larger than 5 1/2 meters (17 feet) in diameter, increasing the cost and making them unwieldy, rendered it necessary also to concentrate the slimes in several operations, because the travel over so short a length of hearth would not suffice for close concentration. A preliminary sizing is effected in a system of spitzkasten. Herr C. Linkenbach, general manager of the Ems Lead and Silver Works, Germany, devised a buddle, in 1878, which has since worked well and found much favor in Germany, and has been in one instance copied here, at Colorado Springs, without any credit having been given to the original inventor. Linkenbach's plan has been to reverse the functions of the table and the washing apparatus of the old German revolving table. He makes the tables stationary and rotates the washing apparatus,, thus enabling him to save in power, and, within certain limits, to increase the dimensions of the table, without in any way affecting its durability or materially increasing its cost. In its earlier form, the buddle was single, and that type is still

Jan 1, 1883

On Monday, October 25th, 1971 at approximately 12.15 a.m. the night shift proceeding underground discovered smoke at No.1 and No-3 cut throughs on the eastern side of the belt heading and in close proximity to the upcast shaft. Attempts to control the fire continued throughout the morning; as the position underground altered various procedures were adopted in an effort to contain and control the fire. Despite these efforts at approx. 12.40 p.m. a sudden change occurred which made it necessary to withdraw all workmen from underground, the vicinity of the Tunnel entrances and upcast shaft. Sealing of the mine at the entrances was the only remaining alternative. Several boreholes were put down to enable sampling of the atmosphere and air temperatures to be taken. This was essential as a guide to determining when conditions were suitable to allow exploration of the area using mine rescue self contained breathing apparatus.

Jan 1, 1972

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By K. I. Afewu, L. C. Woollacott

Little is reported in the literature that is directly useful for the interpolation film coefficients for the in-pulp adsorption circuits used in gold metallurgy. This can create a problem if the design or operation of these circuits is to be optimized by the use of simulation techniques. To address this problem, a study was undertaken on the influence of mixing intensity, scale, and geometry on the film coefficient in adsorption systems typical of the carbon-in pulp plants used for gold extraction. This, the first paper deals with the influence of these factors on the film coefficient and shows that the specific power to just disperse the carbon in the slurry is an important variable. This variable is also strongly dependent on mixing intensity, scale, and geometry-a dependence that is dealt with in the second paper in the series. From the informatlon obtained, practical scale-up procedures were developed. These procedures are considered to be applicable to resin-in-pulp as well as to carbon-In-pulp plants.

Jan 1, 1995