Search Documents

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977

By Gordon A. Gross

During the last half century major steel industries of the world have become dependent on iron and manganese resources derived from siliceous ironformation sediments. More than two billion years ago vast amounts of iron and manganese were deposited in ironformation sediments on all continents and until recent years their genesis was considered to be a uniquely Precambrian phenomenon. Research work has demonstrated that the origin of the banded ironformations was related to major tectonic features and associated volcanogenic processes that were active throughout geological history. Similar sedimentary-tectonic environments are being explored on the seafloor where metalliferous sediments are forming today. Ironformations are now considered to be a major part of the stratafer group of stratiform metalliferous deposits. They developed in sedimentary basins in areas where deep tectonic fracturing intersected high thermal gradients in the earth?s crust and gave rise to profuse volcanism and the hydrothermal effusive discharge of metals in the vicinity of the volcanic centres. Concepts for the genesis and metamorphism of stratafer deposits as revised in the last half century have had a profound impact in the development of iron ore resources and have had a dramatic impact in the use of metallogenetic concepts for guiding exploration for other mineral resources. They are based on the tectonic history and stratigraphy in the sedimentary basins, the role of hydrothermal volcanogenic processes , as well as environmental and sedimentation factors which influence the deposition of silica, iron , and other metals that were emphasized in the past. Topics of special interest in the genesis of ironformation and stratafer deposits and for guiding mineral exploration are: biomediation in their sedimentation and genesis, the significance of metamorphism in the processing and beneficiation of iron ore and in the genesis of iron ore by natural enrichment processes, syngenetic concentrations of Mn, Ti, Cu. Zn, Pb, Ni, Co, REE, F, Ba, B, As, Hg, W and Au in ironformations and stratafer lithofacies, and the mobilization of gold and other elements by alkaline solutions during diagenesis of ironformation and other stratafer metalliferous sediments.

May 1, 2003

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By Walter Pajalich

This Bureau of Mines report is a study of the organizational framework of the ferrous scrap industry, of the products produced, and of the factors affecting the consumption of ferrous scrap by the steel industry. Consumption data from 27 major iron and steel firms in the States of Illinois, Indiana, Iowa, Michigan, Minnesota, and Wisconsin during the period between 1957 to 1962 were grouped by type of iron and steel furnace production facilities to determine consumption pattern for various grades of scrap in comparison to ingot production, hot metal consumption, and home scrap generation. Grades of scrap affected by changes in scrap consumption were determined, and the pattern that emerged was analyzed. Correlation of scrap demand and its effects on scrap prices based on price of scrap receipts of No. 1 heavy melting scrap and No. 2 bundles in the Chicago area for the years 1957 through 1962 indicated that demand trends do not always affect the price of scrap, Past and present technological advancements in steelmaking processes are discussed, and their effects on the scrap industry are analyzed.

Jan 1, 1967

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By S. Singh, R. C. Deshpande

RECENTLY metallographic studies of copper slugs recovered after firing shaped charges in deep containers of water were reported.' The present note describes the metallographic examination of a steel

Jan 1, 1960

By Partha Patra

Extracellular bacterial protein (EBP) from Paenibacillus polymyxa was isolated. Adsorption of bacterial cells of Paenibacillus polymyxa as well as EBP onto pyrite, galena and sphalerite was studied. Both bacterial cells and EBP was found to have different adsorption density for different minerals. Protein from mineral surfaces were extrated and examined through SDS PAGE electrophoresis. Specific group of protein was found to be adsorbing, specific to respective minerals. EBP was fractionated through FPLC. Adsorption studies were carried out with each fractions. Difference in adsorption density was observed for individual minerals. Flocculation and flotation experiment were carried out with these mineral specific EBP. Pyrite was selectively removed from ternary mixture of galena and spharite through flocculation anf flotation using pyrite specific EBP. Mineral specific EBP was found to selectively separated remove pyrite from the complex sulphide mixture.Zetapotential studies were carried out to examine the surface chemical changes of the minerals on interaction with EBP. Hydrophobicity of the minerals were carried out on interaction with bacterial cells as well as mineral specific EBP.

Jan 1, 2006

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By Rakesh Kumar, S. Mehrotra, T. Alex

"This paper, an overview of our recent findings on mechanical activation (MA) of minerals/materials, emphasizes the importance of sample genesis, mechanically induced/altered porosity and surface area, mineral interactions, glassy inorganic materials, surface alteration and zeta potential changes and, mechanically induced reactivity of solids. Materials investigated include Al-oxyhydroxides (gibbsite and boehmite), fly ash and granulated blast furnace slag. Planetary, attrition, vibratory and conventional ball mills are used for MA. Genesis of boehmite has been found to have a bearing on its behavior during MA. For example, BET specific surface area (SSA) of boehmite prepared by thermal dehydroxylation of gibbsite has decreased from 265 to 65 m2/g during 240 min of MA; in contrast, the SSA of hydrothermal boehmite has increased from ~2 to 36 m2/g. Mechanisms of surface area changes in the two boehmite samples differing in their genesis is explored. MA of gibbsite and its mixture with hematite/quartz using attrition milling has indicated that the presence of the second phase promotes amorphisation. Amorphous materials show signs of change in nature of bonding during milling as illustrated by MA of fly ash. Physicochemical changes during MA are not restricted to the bulk phase. The genesis of zeta potential changes in MA solids can be many; for example texture induced zeta potential changes as observed for gibbsite, while zeta potential changes during the milling of granulated blast furnace slag occur due to enhanced (possibly non-congruent) dissolution. Interesting manifestations of mechanically induced reactivity and its correlation with physicochemical changes are illustrated in terms of alkali leaching of boehmite and, hydration of MA slag. New findings reported here are associated with several open questions and are highlighted in the paper."

Jan 1, 2014

By Pier Luigi Iovino

As Technical Director of the Naples, Italy based Fondedile, a geotechnical construction firm specializing in static restoration of structures, Fernando Lizzi, Ing., devoted over 30 years to the pursuit and advancement of static restoration and subsoil strengthening. Seismic events, construction of new structures on polluted and/or unstable soils in urban areas, and a need to carefully preserve and restore delicate, war-damaged historical structures, manifested the need for underpinning projects. Traditional construction methods and approaches, such as underpinning with additional foundation masonry, were not suitable and would have further jeopardized the stability of the structures. The introduction of the palo radice (root pile) revolutionized the field of underpinning. At the time of the first application of micropiles, the industry standard was driven piles. The drilled micropile was conceived and first implemented in the early 1950s, as an innovative means to underpin sensitive, historic structures and structures in urban areas. Specifically, the new construction technique was conceived as a less expensive alternative, designed to accept structural loads, be installed in limited access areas, in varied working and sub-surface conditions, which did not involve changing soil characteristics, and had minimal disturbance to the structure being underpinned, or to adjacent structures.

Jan 1, 2003

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Senanayake G

A sample of crude copper powder produced by the CLEAR Process was refined by dissolution and recovery in sulfate media using the Parker Process. The Parker Process offers an alternative method of copper recovery to electrorefining and allows a range of Eh and pH conditions to be used to provide further discrimination of impurities. High purity copper powder was recovered by the Parker Process even in the presence of added impurities when the Eh and pH was maintained near constant throughout the refining step.

Jan 1, 1984

By Richard D. Hagni

Although the economically important uranium minerals are difficult to recognize under the ore microscope, they can be identified by a combination of qualitative and quantitative techniques. Useful quantitative techniques include indentation hardness, percent reflectance, spectral reflectance curves, and color coordinates. The latter two properties are especially distinctive for the primary urahlferous minerals uraninite, coffinite, brannerlte, and davidite. Together with the quantitative properties of indentation hardness and reflectance, the character and color of internal reflections are distinctive for many of the secondary uranium minerals. Ore microscopic techniques also provide an excellent means for determining the intergrowths of these minerals with other ore and gangue minerals. Such intergrowths are important to an understanding of the genesis of uranium deposits, and they may be important to uranium extractions.

Jan 1, 1981

The applicability of Bieniawski and Hoek-Brown empirical strength criteria has been assessed for different groups of coal and various types of intact rocks by using a vast number of published triaxial test data from various places. Analysis of individual data sets revealed that the traditional forms of the criteria do not have a perfect agreement with the data. A strong negative correlation has been observed between B in Bieniawski's criterion and m in Hoek and Brown's criterion with uniaxial compressive strength of materials. Both criteria have been modified and empirical relationships have been introduced for coal as follows:m = 62.903 - 34.213 (log pc) 0.9772B = 10.152 - 4.709 (log pc )0.8889Similar relationships have been developed for different rock types as well.A comparison between the applicability of each of the above approaches with the conventional criteria reveals a very significant advantage for new approaches and a supremacy for the Bieniawski criterion in all cases particularly in the case of coal.The modified Bieniawski criterion fits coal as well as different types of rocks with excellent accuracy.The modified Hoek-Brown criterion gives a good result for rocks but does not fit coal data quite well. In other words, Hoek-Brown criterion is not an suitable one for coal.

Jan 1, 1998

By Howard N. Eavenson

In many of the bituminous-coal districts of this country, more than one seam of workable coal exists, and in most cases the lower seam is the more attractive, owing to either its greater thickness or its superior quality. Apprehension that the mining of a seam will destroy the availability of all overlying seams has hindered the development of many fields and has led to the unprofitable working of certain seams in order to save them from an expected total loss. The U. S. Coal & Coke Co., Gary, W. Va., was the first operator in the Pocahontas field to mine the No. 4 seam extensively, which occurs about 80 ft. above No. 3, the scam that was worked first. This was due to the fact that over large areas the upper seam was the only one of workable thickness, at that time. In two places, both seams were workable in the same area, the No. 4 being thinner and containing more impurities than No. 3 seam. In mining these areas, an attempt was made to keep the workings in the upper seam in advance of those in the lower one, and no pillar robbing was done in No. 3 seam until after pillars in that part of the upper seam directly over it had been mined. This resulted in an excessive development in the lower seam, with large areas of finished rooms and standing pillars. The top fell badly, and after a couple of years the falls became so heavy that pillar drawing was unduly expensive. To overcome this obstacle and allow No. 3 seam to be worked in some territory where No. 4 was thick, but too dirty for present use, a study was made of operating methods applied to superimposed seams in Pennsylvania and Maryland. This was started more than seven yean ago by the writer; his data, supplemented by more recent information gathered by his associates, and by two cases mentioned in recent foreign publications, form the basis of this paper. Central Pennsylvania In central Pennsylvania, the lower coal measures contain several seams of nearly the same thickness but of varying quality, and as mining

Jan 1, 1923

By H P. Rossmanith

This contribution addresses the advanced blasting technology which is based on wave propagation theory and fracture mechanics. The new concept of sonicity and the principle of maximizing sonicity in blasting as well as the energy or work of a blast operation will be introduced. It is shown that - in contrast to common belief – it is not the velocity of detonation which controls the blast but the relationship between velocity of detonation and the wave speeds, in other words, the Mach numbers of the blast operation. Based on numerous practical blasts in Germany, the authors show that, when using wave dynamic concepts, there is a linear relationship between peak particle velocity and the work of a blast operation and this linear relationship is controlled by the sonicity of the blast. Extensions to layered and faulted rock masses are presented. It will become clear that a second change of paradigm is enforced, the first one being the implementation of short time delaying. Again, the acquisition of knowledge in wave progation theory and fracture mechanics becomes mandatory in advanced blasting technology, where the art of blasting is now fully transformed into a science of blasting with little room for methods of trial and error.

Jan 1, 2010

Surface geological observations are predominantly two-dimensional but can be expanded into three dimensions using geophysical techniques. These techniques have proved succ- essful in the past and will be utilised more frequently in future mineral exploration. Geophysical training establishments must recog- nize future requirements and teach geophysics as part of a broad earth science course as well as a specialised geophysical course. Central- isation of teaching skills, the use of high- technology in the classroom, and greater interaction between academic and industry staff are recommended as a means of ensuring a vibrant geophysical training base in Australia, for the geophysicist of the future.

Jan 1, 1986