Search Documents

By E. J. Rapperport, J. P. Pemsler

The thermodynamic activities of zinc in six solid solution Cu-Zn alloys ranging from 5 to 35 at. pct Zn were determined experimentally in the temperature range 400° to 600°C. This low temperature investigation was canducted in order to evaluate techniques developed to utilize the inherently high sensitivity of atomic absorption flocesses in the measurement of thermodynamic activities. Analytical expressions ,for the activity and actizlity coeflcient are given for the six alloys in the temperature ranges investigated. RELATIVELY few experimental methods are available for investigation of thermodynamic activities of alloys, especially in the solid state. The techniques most frequently used have been the electrochemical potential and the effusion methods, both of which have severe limitations in many instances. It is therefore desirable to expand the ability to perform such measurements in order to obtain new information as well as to provide an additional independent verification capability. In this work, we present a significant improvement in the spectrophotometric method for sensing small vapor pressures in static absorption cells. Similar techniques have been used previously;1"5 however, applications had been limited to relatively high pressures, often greater than 1 torr. Prior investigators have, for the most part, used broad spectral sources such as xenon or mercury lamps, and high intensity arcs. Hollow cathode sources were first suggested in 1956 6 and were used soon afterwards.4'5 These sources offer significant improvements in sensitivity and freedom from interfering spectral lines.'-' EXPERIMENTAL High purity zinc was obtained from Cominco Products, Inc., and copper from American Smelting and Refining Co. Both elements were of 99.999 pct purity. Copper-zinc alloys were vacuum melted in a high fired carbon crucible with each alloy pulled from the melt as a 4 -in. diam bar. The bars were swaged to -1/4 in. rods and vacuum annealed for 160 hr at 800° + 1°C. Samples for gross chemical analysis were taken at intervals along the length of the rods to ascertain the axial zinc gradient. Electron microprobe analysis of homogenized specimens indicated that the alloys had uniform compositions over their cross sections on a macro (200 p) and micro (1 u) scale to better than *1 pct (20) of the gross composition. This tolerance was determined by counting statistics, rather than assured composition fluctuations. All SiO 2 windows were high-ultraviolet-transmission grade to minimize intensity losses. Silica absorption cells were scrupulously cleaned consecutively in organic solvents, dilute HF, and distilled water before use. The empty cells were then flamed while under a dynamic vacuum, cooled, and removed to an argon-filled glove bag. Alloy pieces were cut and filed in the glove bag to produce fresh surfaces, and then loaded into the cells. The loaded cells were temporarily sealed, removed from the glove bag, reevacuated to 10-5 torr or better, and permanently sealed. The instrument used is schematically shown in Fig. 1. The spectral emission from a commercially made hollow cathode lamp (A) of a selected element is focused through an absorption cell (B) inside a well-controlled furnace (C). The intensity of the transmitted beam is measured using the spectrometer* (D) 'Techtron model AA4 atomic absorption spectrometer. which contains a grating (E) that disperses the light prior to impingement on the photomultiplier (F). The monochromator grating is adjusted so that only the wavelength of interest is measured. The power supply delivered an interrupted voltage to the lamp, causing a chopped radiation output to be transmitted. The detector read only the intermittent component of radiation incident upon it, so that all continuous noise signals (furnace radiation, and so forth) were eliminated. Three recording thermocouples contained in the muffle furnace were positioned along the length of the absorption cell: one at each end and one at the center. An effort was made to keep the ends of the cell several degrees hotter than the center to avoid window condensate. Appropriate thermal corrections were then necessary to relate cell pressure to radiation attenuation. Water-cooled heat shields, as shown in Fig. 1, were found to aid signal stability by protecting the hollow cathode and the photomultiplier from furnace radiation. The furnace had a 2-in. diam muffle, Kan-thal wound, with SiO 2 windows at its ends to minimize convective effects. The hollow cathode radiation was masked and focused to form a conic beam that was a maximum of { in. diam within the furnace. Thus, the 1.5 in. diam absorption cell easily contained the entire beam. The furnace was mounted on ball-bearing slides with positive positioning detents. This arrangement allowed the removal of the entire furnace assembly from the radiation path, position [I], Fig. 1, so that frequent sampling of the unattenuated beam intensity could be obtained. In all cases the beam intensity was kept constant to 0.1 pct as judged by readings taken immediately before and immediately after data collection. Only data for absorptions of less than 80 pct were utilized, as systematic deviations from linearity were found for greater absorptions.

Jan 1, 1970

In the death of Professor Hofman, the world has lost a great metallurgist and a great author of metallurgical literature. Measured in time, his life was not quite seventy-two years, but measured in work accomplished it was much longer than this. He was born Aug. 13, 1852 and died Apr. 28, 1924. It is not surprising that Doctor Hofman became a great scholar, for his father, Karl Hofman, was on the faculty of Heidelberg University, and his early days were spent in those surroundings. He studied in the university under such men as Kirchhoff and Bunsen and often spoke of his

Jan 1, 1924

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By G. I. D. Roach

The leaching, with hydrochloric, sulphuric and perchloric acids, of suspensions and massive specimens of different haematite and goethite samples has been studied. Both accelerating and constant types of leaching curves have been observed. It is concluded that the grain to particle size ratio of the oxide being leached determines which type of leaching curve is obtained, particles containing a large number of individual grains producing the accelerating type of curve

Dec 1, 1971

By J. J. Webb

At Kerr-McGee's Galatia Mine in southern Illinois, the need for safe and efficient longwall moves prompted a detailed planning effort. Galatia Mine operates two longwalls on separate coal seams with different geologic conditions. An overview of the longwall move planning as related to manpower training, roof control, ventilation, transportation, equipment recovery and setup will be discussed. The impressive safety record achieved during each of the longwall moves at Galatia Mine verifies that health and safety planning does play a major role.

Jan 1, 1994

By R. J. Traube

The purpose of the Inherently Safe Mining System (ISMS) project is to develop continuous and conventional coal mining equipment and systems which will reduce the incidence of fatal and nonfatal accidents in the working sections of underground bituminous coal mines by application of existing technology. This 3-year program, initiated on 18 June 1971, is being conducted in three phases: ? PHASE I (8 months) Systems Analysis Concept Design Planning ? PHASE 11 (16 months) Design Procurement Manufacture Preliminary Testing ? PHASE III (12 months) Underground Coal Production Demonstration.

Jan 1, 1972

By Frank W. Pereira

The Montana Talc ore body was discovered in 1983 in Montana's Gravelly Range, about 40 km (25 miles) south of Ennis. Initial drilling indicated a 910-kt (1-million st) ore body of high purity talc. Preliminary analyses on ore cuttings included chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. Results indicated it was similar to talc currently being marketed from Montana and it would probably have good commercial value. Based on the positive test results, a test pit was made and a 180-t (200-st) sample of ore was mined. A portion of the ore was ground to various particle sizes and evaluated to determine its strengths, weaknesses, and other characteristics. The deposit is located close to the Cyprus Yellowstone deposit. It was therefore believed that Montana Talc ore may possess many of the same characteristics. Testing and analyses showed the talc to have a high purity and an extremely large surface area, even for Montanatype tales. The ore was also situated in a massive deposit, indicating low cost mining. While the lab analyses were encouraging, the true evidence would be obtained from commercial tests in the marketplace. About 91 t (100 st) of ore were ground to product specifications for pitch control, paint filler, and plastics filler. Consumers were contacted and requested to evaluate the sample talc products. A major trial for the talc as a pitch control agent was arranged at a Northeast paper mill. The trial indicated the new Montana Talc product performed as well or better than the current standard in the industry. In fact, due to a minor modification in the compaction process to make the transport of the talc easier, the product had substantially less dust than the currently used product. The operating people at the paper mill requested that management purchase this talc. Trials were also run at paint plants for use as a pigment filler. And the talc was fabricated into a number of plastics compounds. The initial product tests were largely positive and provided encouragement to proceed with the project. Different grinding mills were used and their performance evaluated. Significant data were generated by the custom grinders. They indicated how the Montana Talc ore ground and the particle size distributions produced at different grinding settings. Encouraged by the positive marketing tests, a prefeasibility study was commissioned. A talc grinding plant and mine plans were designed and capital and operating costs estimated. Initial economics showed an attractive return. The operating costs were among the lowest in the industry. The positive economics, along with the excellent results by the products in the marketing tests to the paper, paint, and plastics industries, led to the recommendation to proceed with the project. Plant construction began in June of 1985. The Montana Talc Co. (MTC) analyzed the data from the commercial tests. Based on the product's outstanding performance and the uniqueness of its high purity and platy structure, a strategy was developed to position the company as a premium talc supplier.

Jan 1, 1989

By John C. Ferm

Although roof falls account for approximately half of the fatalities in underground coal mining, the factors that produce them are not clear. Mining methods can account for some, but in others the controlling factors are the geological setting in which the mining takes place. The present investigation was undertaken to determine the kinds of rocks that were most likely to produce roof problems. Such knowledge would be helpful to mine planning since rock samples can be obtained in advance of mining by core hole drilling. The investigation was undertaken in underground mines in the Pocahontas #3 seam in southern West Virginia and southwestern Virginia. The Pocahontas #3 is one of the most widespread in this region and is a major source of high quality metallurgical coal. There are at least ten very large mines in the area and many smaller ones. The region has a very long mining history and considerable experience has been gained in roof control problems. The study was conducted with the support of the U. S. Bureau of Mines.

Jan 1, 1978

COMMITTEE OF ARRANGEMENTS. General Committee.-J. F. Lewis, Quinnimont, W. Va. Committee of Reception at Staunton.-Major Jed. Hotchkiss, Chairman ; W. A. Burke, M. E. Miller, R. N. Catlett, W. J. Nelson, J. T. Effinger, D. A. Kayser. Local Committee of Arrangements.-G. T. Wickes, Low Moor, Chairman; G. W. Bramwell, Stone Cliff, Secretary; J. E. Johnson, Longdale; H. Firm¬stone, Longdale; S. F. Morris, Quinnimont; O. A. Randall, Ferrol; William N. Page, Ansted; F. Lyman, Low Moor; S. M. Buck, Coalburgh; E. S. Hutchinson, Cannelton ; M. F. Maury, Saltpetre Cave. THE opening session of the Institute was held at Staunton, on Monday evening, May 30th, in the Opera House. Major Jed. Hotchkiss, Chairman of the Committee of Reception, called the meeting to order and introduced Mayor Balthis, who spoke a few words of welcome to the members present, and then introduced the Hon. A. H. H. Stuart. Mr. Stuart in addressing a formal welcome to the Institute to the " little city of the mountains," spoke of the value of the services of the mining engineer in developing the mineral wealth of Virginia and in solving the problems of her geological history. Mr. Metcalf, President of the Institute, replied on behalf of the Institute to the cordial welcome of the mayor and Mr. Stuart, and then read an inaugural address on Force. At the conclusion of the President's address the following papers were read The Electrolytic Determination of Copper and the Formation and Composition of so-called Allotropic Copper, by J. B. Mackintosh, Hoboken, N. J. Read by Professor Egleston. The New Unpublished Map of Chester County, Pa., by Professor Persifor Frazer, Philadelphia. The second session was held at the Opera House on Tuesday morning. The papers read at this session were: Investigations on the Ore Knob Copper Process, by Professor Thomas Egleston, School of Mines, New York city. A Volumetric Estimation of Manganese in Pig Iron and Steel, by F. H. Williams, Vulcan Steel Works, St. Louis, Mo. Read by the Secretary.

Jan 1, 1882

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By M Spiteri, S Woth, J Caratti, K Henley

Blasting is an essentially violent process aimed to disrupt and loosen rock for productive excavation and downstream processing. Dilution of the orebody to some extent is the inevitable result, particularly in narrow vein gold mines. A small change in gold recovery is usually a strong lever on revenue generation. As a result blast designs are carefully engineered to both minimise and control the direction of rock movement. Traditionally blast designs in gold mines have used the minimum powder factor that will still permit rock excavation. This now conflicts with the recent industry trend to optimise the total process flowsheet from the mine to the mill. Numerous mines have achieved success in reducing total mining cost by increasing powder factors. Not only is explosive energy cheaper than mechanical comminution energy requirements, the increased blasting effect may deliver benefits across all downstream processes of digging, hauling, crushing and milling. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation is the largest gold mine in Australia, located in the heart of the Kalgoorlie Goldfields. Blast dilution has been reduced at KCGM by managing location of blast boundaries and by firing along strike to choked faces. Significant economies of scale have resulted from application of a bulk mining methods. The bench height of 10 m is the largest in the Western Australian Goldfields, and is typically mined in a single pass with large face shovels. Recent increases in production rates in both the mine and mill has been partly attributed to a 30 per cent increase in powder factor. KCGM then examined the benefit of a further 18 per cent increase in powder factor to 1.0 kg/BCM. A concern though was the impact of very high powder factors resulting in excessive blast movement and subsequently ore dilution. This was the subject of a project conducted with Orica Explosives. OricaÆsDMC(Distinct Motion Code) blast model was applied to understand the effect of not just further increases in powder factor but also blast geometry and explosive type. The modeling work demonstrated that high powder factors may be applied with minimal increase in ore dilution provided the combination of blast geometry and explosive type is optimised. These results are currently being implemented to achieve further reductions in total mining costs without a significant impact on recovery.

Jan 1, 2001

By Paul J. Lewis

Replacement of the Monroe Street Viaduct in southwest Baltimore City, Maryland included transforming 240 feet of the south approach from a pile-supported multi-span bridge to a mechanically stabilized earth (MSE) embankment supported by vibro-concrete columns (VCCs) and a load transfer platform. The project area was underlain with highly compressible soils which would have resulted in up to 18 inches of settlement under the proposed embankment load. Adjacent structures and critical underground utilities would have been impacteded or damaged by this settlement. Various load transfer alternatives were evaluated to mitigate the anticipated settlement by supporting the embankment on a deeper, more competent stratum. The alternatives considered included compaction grout columns, stone columns, deep soil mixing, and VCCs. Deep soil mixing was eventually selected for design, however, as part of a value engineering proposal, the general contractor Joseph B. Fay Company, with assistance from Hayward Baker and the Collin Group, prepared and submitted an alternative consisting of VCCs. This paper presents the details of the value load transfer platform and VCC design. Loading tests were utilized to confirm the VCC capacity and field changes were implemented based on the test results.

Jan 1, 2007

By André van Wageningen

Long-term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. Although a number of techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimisation techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the solution search space. The GA itself contains very little problem specific information and as such, has been linked to a discrete-event simulation (DES). The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimisation process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GA coupled DES is then used to ?optimise? a problem and the results are discussed.

May 1, 2004

By A. Ghahreman

Activated carbon is proven to be able to catalyze arsenic oxidation in aqueous solution under acidic conditions. A commercially available granular coconut shell based activated carbon (AC) has been evaluated for catalysis of arsenic oxidation in this study. The rapid small-scale column test (RSSCT) has been developed to simulate and predict the performance of a carbon-based arsenic treatment system in a pilot scale reactor. Effects of residence time, aeration rate, and initial arsenic concentration in the influent solution on the AC catalysis of arsenic oxidation under dynamic and continuous conditions were studied by manipulating these parameters during RSSCTs. The effectiveness of the AC on arsenic oxidation was examined over the course of constant diffusivity based RSSCT operation. Residence time and initial arsenite concentration are proven to be the most effective impacting parameters on the arsenic oxidation process. For the 218 min residence time, the highest steady-state arsenic oxidation efficiency achieved was 98% with 1 g/L As(III) being treated at pH=1 under 0.05 L/min oxygen aeration. In a long-running RSSCT, the oxidation efficiency did not seem to deteriorate over a course of 666 hours operation, corresponding to 13986 mL total influent throughput volume. INTRODUCTION Arsenic is toxic to both animals and plants and inorganic arsenicals are proven carcinogens in humans. The increased extraction of low grade and complex mineral resources has introduced high ratios of arsenic into metallurgical processes. Discharge of arsenic by acid mine drainage resulting from mining activities has added intensive pressure on the need for proper treatment (Lawrence & Higgs, 1999). Since trivalent arsenite is more toxic and has lower affinity to solid surfaces for adsorption, many treatment systems initiate with an oxidation step to convert arsenite to arsenate and reach the ultimate immobilization of arsenic by the following precipitation of arsenate (Nazari, Radzinski, & Ghahreman, 2016). Scorodite precipitation has been studied extensively as a means of arsenic immobilization due to its high stability and negligible potential of releasing arsenic (Filippou & Demopoulos, 1997). As a stable ferric arsenate mineral, crystalline scorodite can contain up to 30 wt% arsenic (Paktunc, Dutrizac, & Gertsman, 2008). Arsenic must be in its pentavalent oxidation state in order for scorodite to be precipitated via oxidizing ferrous ions (Clancy, Hayes, & Raskin, 2013).

Jan 1, 2019

By A. de Meyer

Zincor experienced significant losses of metallic zinc to dross during the melting of zinc cathode plates. In this study five factors affecting the formation of dross are identified from literature. Dross from both the plant and that produced in the laboratory is characterized using XRD. An empirical model, based on laboratory-scale investigations, was developed to quantify the effect these factors on their own or in combination with each other has on the amount of zinc loss to dross. The predictive capability of the model is evaluated based on the laboratory-scale investigations. Predictions are made on the effects that heat treating the cathode plates prior to melting, increasing the cathode plate thickness, washing and drying prior to melting, and loading the furnace in a controlled manner have on the amount of zinc loss to dross. Keywords: Zinc, dross, optimize, smelter, yield, losses, empirical, model, XRD.

Jan 1, 2010

With only one certain exception coal was never used by the Indians, before white men came to America, for any purpose except as an ornament or for paint. Within the past few years it has been discovered that the Hopi Indians in Navajo County, Arizona, used lignite for burning pottery, about 1000 A. D., as dated by tree rings. They were able to obtain a clear color in their ware that could not be obtained with brushwood fires. The coal was mined by hammers from outcrop openings, some of which can still be seen, and the tools used have been found in them.1 (See also p. 376.) Small figurines made of splint or cannel coal have been found at various localities in western New York, in Ohio and possibly other places, evidently made for ornaments. There is no reason to think they are of any greater age, if as old, as that mentioned above. Some crushed coal was used by the Indians as a black pigment in painting themselves, but apparently the eastern Indians never used coal for any other purposes. Some think that several tribes of Indians in the Northwest, along the Missouri, used coal as fuel, the basis being a statement attributed to Radisson about 1660. In the Jesuit Relations of 1659-1660 it was stated that Radisson anti Groseilliers had just returned from a visit to Lake Superior and beyond. "In the country of the Poualak, which means 'warriors' they say `as wood is scanty in supply and small in size in their country, nature has taught them to make fire with coal from the earth (charbon de terre) and to cover their cabins with skins.'"2 This statement was only hearsay with the good fathers, and the reputation for veracity of the two explorers is not of the best, and it is extremely probable that instead of coal they used turf, dry grass or buffalo chips. In fact in Radisson's Voyages' he does not mention coal at all in his account of the third voyage, when he was supposed to have seen it used. His accounts of his travels are badly mixed, and he and his companions were much better travellers than narrators. None of the early travellers up the Missouri River saw any evidence even then that the Indians were familiar with the use of coal. In the writer's opinion it is unlikely that coal was used as stated by the Jesuits.

Jan 1, 1942

By P. Kawahata

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on-site facilities depending on ore type and grade. Processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off-site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and complexity of the operation, there are unique challenges in optimizing life-of-mine production scheduling. This paper describes those challenges and methods developed to take advantage of different scheduling software to effectively compensate each other and result in reasonable guidance. This paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Jun 1, 2013

By Alyson Morley

The mining sector in Canada is facing significant challenges to develop a competent workforce, including increased technical and logistical operational demands, and the imperative to promote local content. There is an increasingly unpredictable labour pool which can be aging, or have skill shortages, or non-aligned skills. As globalisation continues, companies also require efficiencies during operation across various locations. AMEC has met these challenges in the global oil and gas sector by developing our Capability Development and Competence Assurance (CDCA) program. CDCA is applicable across all process industries, including mining. CDCA supports simultaneous consistency and flexibility by defining competence at task level, with corresponding best practice blended training programs, and evaluation criteria and processes. CDCA then defines role profiles mapped to local task definition. When combined with web-based technology, this granularity allows us to manage high volume workforces, while retaining individual learning plans and progression, aiding job satisfaction, and employee retention.

May 1, 2007

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By T Do, J Siliezar, M Larson

With the expansion of magnetite projects in Australia has come the opportunity to take advantage of newer technologies that were not necessarily available when the magnetite industries of North America and Europe were maturing. One of these technologies is the IsaMill, originally developed for the economic treatment of ultra-fine grind (UFG) duties of Mount Isa Mines. As understanding of the IsaMill has increased, so too has the ability to process coarser feeds while maintaining the same energy efficiency advantage and tight product size distribution that originally made the IsaMill so attractive. In the case of magnetite the hard non-elastic ceramic grinding media is ideally suited to the grinding duty when compared to steel grinding media. The centripetal separator and naturally steep product size distribution curve provide a mill discharge that maximises the critical concentrate grade. This paper analyses the effect of the IsaMill grinding technology on the full-scale Ernest Henry Mine (EHM) magnetite operation along with pilot and lab scale demonstrations of optimisation. Issues encountered and the solutions to maximise the mill throughput and quality are examined in an effort to promote better understanding across the industry. CITATION:Larson, M, Do, T and Siliezar, J, 2013. Enhancing magnetite returns - the benefits of IsaMilling, in Proceedings Iron Ore 2013 , pp 411-416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013