Search Documents

By O. D. Gonzalez

Existing measurements for the steady-state permeation of hydrogen in a iron above 100°C have been examined for contribution of determinate errors. The analysis leads to a recommended equation for the permeability of hydrogen in a iron: o= (2.9 ±0.5) x 10-3 exp - (8400 ± 400)/RT cu cm (ntp H2) cm-1 sec-1 atm-1/2 THE permeability of a iron to hydrogen has been the subject of numerous investigations over the past 40 years, and at present there are thirteen sets of published results for the rate of steady-state permeation of hydrogen in a iron above 100°C. The numerical values in each set of results are entirely self-consis-tent, but the spread among the sets is too large to be attributed solely to experimental error, i.e., to error other than in the specimen itself. Several reasons have been advanced to explain the disparities, but to date the relative importance of experimental inaccuracy to the spread remains uncertain. The purpose of this report is to examine in detail the sources of determinate errors inherent in the experiments and to assess as far as possible the contribution of the errors to the results. The ultimate goal is the selection of values for the permeability and heat of permeation most nearly representative of hydrogen in a iron. The analysis is limited to those experiments in which the permeation rate was observed at steady state—a condition in which traps for hydrogen within the metal are filled to a fixed level15 so that the trapping mechanism is not reflected in the rate of passage of the gas. Furthermore only data are examined in which surface processes are judged to have little or no influence on the flow. It is hoped with these restrictions to obtain values of the permeability and the heat of permeation which will be as closely related as possible to the mechanism of lattice diffusion. I) DEFINITION OF TERMS; UNITS In this report the data for permeation are given in terms of a coefficient oj permeability, ?, which is defined by the equation: jt=?A/?x{p1/2-po1/2) [1] where jt is the total flow of gas normal to the surface of a membrane of planar geometry, e.g., a disc, of area A and thickness ?x; pi and po are the pressures in the input and output sides, respectively. For flow radial to the walls of a membrane of cylindrical geometry, e.g., a tube, the corresponding equation is: where 1 is the length of the cylinder, and ri and ro are the inner and outer radii, respectively. The flux normal to the surface is given by Fick's law: j= -D(dc/dx) [3] At steady state the concentration gradient will be constant, and integration of Eq. [3] gives for the total flow through a disc of area A and thickness Ax: h =-DA(co - ci) [4] where c, and ci are the concentrations of solute at the output and input surfaces, respectively. When surface control is absent, co and ci are given by Sievert's law c = Kp1/2, and substitution therewith into Eq. [4] gives directly Eq. [I] where ? = DK. Integration of Fick's Eq. [3] in cylindrical coordinates will give Eq. [2] where again ? = DK and is thus shown to be independent of geometry (provided that surface control is negligible). The coefficient of permeability, or simply the permeability,* must be expressed in proper units. In *The term permeability will refer in this report always to the coefficient defined above; permeation will be used to specify the general phenomenon of gas passage through a membrane. this report ? will be expressed in the units of cu cm (ntp H2) cm-1 sec-1 atm-1/2. The variations of D and K with temperature are given by D = Do exp(-Ea/RT) and K = KO exp(-?Hs/RT) where E, is the activation energy for diffusion and AH, the heat of solution, each usually expressed in calories per mole of solute. The variation of permeability with temperature will thus be given (for conditions where surface control is negligible) by ? = ?o exp(-?Hp/RT) where ?0 = DoKo and ?Hp = Ea + ?Hs. The units of ?0 are the same as those of 6, and??Hp will be expressed in calories per mole H. 11) SUMMARY OF PERMEABILITY RESULTS Table I gives the values reported to date for the permeability of H2 in a iron in terms of ?o and ?Hp. Except where noted the parameters listed were taken directly from the numbers reported by the various investigators with only a change in units. The temperature limits within which the listed ?o and ?Hp hold are given in column 7; the limits marked in parentheses in this column indicate the entire temperature range covered in each investigation. The listed values of ?o and ?Hp are those giving a linear plot of ln? against T-1 at the higher temperatures in each set of measurements, and thus presumably represent the case for which surface control was negligible. Column 6 gives values of 9 at a representative tem-

Jan 1, 1970

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory' is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2'3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin's suggestion that the free liquid/air interface

Jan 1, 1970

By J. S. Pascover, J. K. Abraham

The influence of the early stages of precipitation on the kinetics and structure of martensite formation in Fe-27Ni and Fe-29.5Ni alloys containing from 0 to 10 pct Ti was examined with X-ray and electron microscopy techniques. The formation of a coherent, ordered preprecipitate had a profound stabilizing effect on the austenite. The Ms was decreased by increased titanium content and aging time up to a critical time. When the critical aging time was exceeded, the Ms was observed to increase markedly. The formation of the clusters was insuppressible and the volume fraction of clusters formed during the quench was a function of the titanium content. Martensite resulting from transformation of the clustered austenite is tetragonal with the c/a ratio increasing with titanium content. A model for the tetragonality is suggested. The morphology and substructure of the m artensite is inter-preted in terms of the above information and the cur-rent models of twinned martensite. ThE ramifications of precipitation in austenite to the properties of austenite have been the subject of numerous investigations. The current research is concerned with the influence of precipitation in austenite on the kinetics and structure of subsequent marten-site formation. In a previous investigation, Abraham et al.1 followed the aging reaction in an Fe-29.5Ni-4.2Ti* (at. pct) alloy using an X-ray diffraction technique. This technique, employing a Guinier camera, provided kinetic measurements through observation of the side band position as a function of aging time. The salient results of this work were: 1) The initiation of precipitation was not suppressed by quenching, i.e., there was a finite cluster zone size at zero aging time; and 2) The hardness of the aged austenite correlated extremely well with the zone size. During the previous work it was noted that the mar-tensite formed after aging was tetragonal, substanti-ating an earlier observation.2 Systematic investiga-tion revealed that the martensite was tetragonal in both the solution-treated then quenched, and the solu-tion-treated, aged, and quenched condition, and, furthermore, that a marked stabilization of the austenite occurred as a function of aging time. The present work is concerned with documenting the tetragonality and the stabilization phenomena as well as the ob- served microstruction with a suggested rationale for the behavior noted. EXPERIMENTAL PROCEDURE The compositions of the alloys are listed in Table I. The analyses were performed after the solution treatment of the strip material. Nickel was determined using the standard dimethy1-glyoxime procedure whereas titanium was determined colorimetrically with hydrogen peroxide and volumetrically by titrating with ferric iron. The materials were melted in a 5-lb vacuum induction furnace, cast into 2-in.-diam ingots, and forged in a temperature range of 950. to 1200°C to 1/2-in. slabs. The three higher titanium containing materials cracked during forging; therefore, to get the alloys into strip form, slices 1/8 in. thick were cut from the slab, homogenized 4 hr at 1150°C, then cold-rolled to a 0.04-in. thickness. The remaining slabs were hot-rolled, homogenized 4 hr at 1065"C, then cold-rolled to a final thickness of 0.03 in. All of the heat treatments were performed under a protective atmosphere of argon. The Ms temperature for most of the alloys is below room temperature; therefore, it was possible to solution treat, quench to room temperature, polish, and then observe the transformation optically on a cold-stage microscope. To determine the effect of aus-tenitizing temperature on Ms, eight of the alloys were treated at two temperatures, 1025" and 1120°C. No measurable variations in Ms were noticed. The remaining alloys were treated at 1025°C. The specimens, : by 5/16 by 0.03 in., were austeni-tized in a vertical tube furnace under a dynamic argon atmosphere. The bottom of the tube was submerged in water for quenching purposes. The question of stabilization that may be operating at room temperature was investigated and found to be negligible. Many of the specimens were held at room

Jan 1, 1970

By Richard H. Siller, Rex B. McLellan

A model for interstitial solid solutions has been considered in which a repulsive Potential exists between interstitial atoms in the solvent lattice. It has been shown that this model is consistent with the thermodynamic Properties of certain interstitial solid solutions. The model is then applied to the calculation of the variation of the diffusivity of carbon in au-tenite with composition. Although the energy levels at the saddle point, and thus the absolute values of dif-fusivity, cannot be calculated, it is shown that by taking the repulsive interactions between the diffusing atoms into account the functional form of the dependence of diffusivity on solute concentration can be derived. ThE composition dependence of the diffusivity, D, of carbon in austenite at a given temperature is well-known.'-3 smith3 tried to reconcile the observed composition dependence of D at 1000°C with the previously observed4 composition dependence of carbon activity using equations for D derived by arken5 and Fisher, Hollomon, and Turnbull,6 but was unsuccessful. In this paper we shall modify the approach of Fisher et al. by considering the "blocking" model7 for interstitial solid solutions, based on concept due to Speiser and Spretnak,' in which a repulsive potential exists between interstitial solute atoms in the solvent lattice, causing a certain number of interstitial sites to be "blocked" from occupancy by further solute atoms. We shall thus be able to describe the intimate relationship between the composition dependence of carbon diffusivity, a kinetic phenomenon, and the composition dependence of carbon activity in austenite. THEORY Consider for convenience one-dimensional interstitial diffusion in an fcc lattice in the [loo] direction. Fig. 1. Assume that solute atoms occupy octahedral sites only.7,9'10 These octahedral sites are located on {lOO} planes a/2Å apart. A solute atom, A, occupying an octahedral site on a {100 } plane denoted by 2, has twelve nearest-neighbor octahedral sites: four on plane 1, four on plane 2, and four on plane 3. Diffusion occurs when there is a net flux of solute atoms, through an imaginary plane shown with dashed lines, from plane 2 to plane 3. Fisher et al6. use the concept of activated complexes, as given in the theory of absolute reaction rates." They show that the number of solute atoms per cubic centimeter per second which pc — Fig. 1-Diagram showing the arrangement of octahedral sites (x) in the fcc lattice. pass in the direction of diffusion from activated to new interstitial position is: ?where C is the concentration of the solute in atoms per cubic centimeter, l/m + is the fraction of new interstitial positions corresponding to motion in the forward diffusion direction (transmission coefficient), ?F* is the free-energy difference between the activated complex and the reactants when each is in its standard state at the temperature of the reaction (independent of temperature and composition in the case of carbon in austenite), y is the activity coefficient of the solute species, and, finally, ym is the activity coefficient of the activated complex (assumed constant). The flux of atoms moving in the forward direction through an area of 1 sq cm perpendicular to the direction of diffusion is therefore: m+ Ym l ' atoms per second where is the distance between planes. The blocking model states that a nearest-neighbor octahedral site of a given solute atom has a probability, f, of being inaccessible to other solute atoms. The number of available sites for diffusion on a given plane will, therefore, depend on f, which is constant, and Nu, the number of solute atoms on that plane. The effect is to have more available sites in the diffusion direction, thereby increasing the net flux of solute atoms. This is reflected in the transmission coefficient, l/m. To calculate the transmission coefficient for solute

Jan 1, 1970

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of silver and copper in dilute Ag-Cu-Sn alloys at 720°K have been determined using a liquid metal-solution calorieter. Values of the se2f-interaction coefficient n AgAghave been calculated at constant copper concentrations and n Cu Cuhas been determined at constant silver contents. The reliability of the experimental data is shown by the very good agreement between nCujAg and ij &$; these interaction coefficients have experimental values of -9100 and - 9590 cal per g-atom, respectively. Certain solution models are shown to be inadequate for prediction of solute interaction coefficients in dilute Ag-Cu-Sn alloys. In a previous publication' the results of a thermody-namic study of dilute Ag-Au-Sn alloys were presented. The present work represents the continuation of a program to investigate dilute alloys of the noble metals with tin and in particular is concerned with solute interactions in the Ag-Cu-Sn system. By determination of the magnitude and sign of the various interaction coefficients in dilute alloys it is possible to gain some understanding of the different types of solute-solute and so lute-solvent bonding changes that occur as the solute concentrations are varied. Hence systematic studies of alloys with similar physical characteristics as regards size, structure, electronegativity, and so forth, of their components can contribute a great deal to present theoretical knowledge of solutions. The recent definition of an enthalpy interaction coefficient, 11, by Lupis and Elliott2 is of particular value in calorimetric studies such as the present one: where j and i are solutes and s is the solvent; Si is the relative partial molar enthalpy of component i and x represents the mole fraction of solute or solvent. Values of ?Hi can be obtained directly by solution calorimetry and data for n are thus easily determined, often with a high degree of accuracy. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hi and to the enthalpy interaction coefficients by the expression: ?Hi?Hi + X;nz+ ... [2] The aim of the present work was to determine the self-interaction coefficients n AgAgand 178: in alloys of different compositions and also to establish values for n Agcg| and ncuAg. Since it is a thermodynamic requirement (resulting from the Maxwell-type relationships which can be applied to partial molar properties) that nAgcu and ncuAg should be equal, a further aim of this study was to demonstrate the agreement between experiment and theory. EXPERIMENTAL A description of the liquid metal-solution calorimeter used in this research has already been published,3 and no further details of its construction and operation will therefore be given here. Copper supplied by the American Smelting and Refining Co. was indicated by them as being 99.999 pct pure, and the silver obtained from A. D. Mackay, Inc., was also quoted as being 99.999 pct pure. A solvent bath consisting of between 70 and 80 g of 99.99 pct pure Sn was used for each series of experimental drops. Its weight was accurately determined and the appropriate amounts of copper or silver were added to give alloys of the desired composition. Approximately 0.00125 g-atom additions were used for determinations of the heat of solution of silver in the bath, while, for copper, specimens consisting of approximately 0.0015 g-atom were used. The heat capacity of the bath was determined at regular intervals during a series of drops using tin or tungsten calibration samples. The heats of solution of silver and copper in pure tin were first determined as a function of their concentration in order to establish the self-interaction coefficients 7AgAg and ncucu Alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of copper were then used to study 17:: in alloys of different copper content, while alloys of the same mole fractions of silver were used to determine equivalent data for 178: at constant silver concentrations. The composition of the bath was held at the desired copper or silver concentration by making calculated additions of the appropriate solute throughout the experiment. From the limiting values of ?HAg in the constant copper content alloys it was possible to study ?HAg as a function of xCu and hence to determine 42:. A similar analysis of the re, values permitted calculation of nAgcu. Heat content and heat capacity data from Hultgren et al* were used to calculate heat of solution values from the measured heat effects at the experimental temperature of 720°K. RESULTS AND DISCUSSION Determinations of ?HAg. A preliminary investigation of the heat of solution of silver in pure tin at 720°K was first made in order to establish the value of nAgAg before additions of copper were made and also to compare the value of ?HOAg(l) with that obtained in the previous study of Ag-Au-Sn alloys.' Then the heat of solution of silver in Cu-Sn alloys was investigated as a func-

Jan 1, 1970

By Carl Altstetter, Emmanuel deLamotte

The influence of an external stress and plastic deformation on the allotropic transformation of single crystals of a Co-30.5 pct Ni alloy was investigated. Experimental results were obtained from dilatometry, X-ray diffraction, and optical and electron microscopy. The effects of stresses could be conveniently divided into three stress ranges. In range I, from 0 to about 400 g per sq mm, the specimens exhibited a multi-variant phase change on cooling and a considerable amount of retained cubic phase. In range II, from 400 g per sq mm to the elastic limit, hexagonal regions of a given orientation grew in size and the cubic phase disappeared with increasing stress level. In range III, just above the elastic limit, specimens transformed into hexagonal single crystals. It was found that plastic deformation, not applied stress, was the factor which determined whether a single-crystal product was formed. The observed macroscopic shear directions were mainly (112) on cooling, but the behavior was more complicated on heating under stress. To explain these properties of the phase change, a model based on the nucleation of partial dislocations is proposed. IT is well-known1 that, on heating, hcp cobalt transforms into an fcc arrangement by shearing on close-packed planes. The crystallographic orientation relationship of the phases is as follows: the habit plane is (OOO1)hcp ?{lll}fcc and a (1010)hcp direction is parallel to a (112)fcc direction. The temperature at which the transformation occurs in pure cobalt is around 420.C 1,2This temperature decreases with increasing nickel concentration: and at about 30 pct Ni it reaches room temperature. However, many of the transformation characteristics remain essentially the same, particularly the crystallographic features.495 A convenient way of studying the transformation is to alloy cobalt with nickel, thus avoiding the difficulties of doing experiments at the high temperatures needed to transform pure cobalt. Due to the hysteresis of the transformation it is possible to choose a Co-Ni alloy with an Ms temperature below room temperature and an A, temperature above room temperature. Either structure of such an alloy could then be studied at room temperature, depending on whether it had just been heated or cooled to room temperature. The choice of nickel is further favored by the small difference in lattice parameters between cubic cobalt and nickel and the similarity of their physical, chemical, and electronic properties. Co-Ni alloys are reported to have neither long- nor short-range order.6 The main purpose of this work was to investigate the influence of an external stress on the transformation characteristics of Co-Ni single crystals. It may be expected that slip, twinning, and transformation should have many features in common in cobalt, because the (111) planes of the cubic phase operate as slip planes when plastic deformation by slip occurs, they are the twinning planes, and they are the habit planes for the transformation. Many previous investigators7-&apos;6 have concluded that dislocations must play an important role in the nucleation and propagation of the transformation, just as they do for slip and twinning propagation. An external stress will affect their motion, and a study of its influence should yield further information about the atomic mechanism of transformation. The present work extends that of Gaunt and christian17 and Nelson and Altstette18 in both qualitative and quantitative effects of stress. The basic concept underlying all the present theories of the transformation of cobalt and Co-Ni alloys is the motion of a/6<112> partial dislocations over {1ll} planes of the cubic lattice. The ABCABC... stacking of the close-packed planes of the cubic phase can be changed into the hexagonal ABABAB... stacking by the sweeping of an a/6 <112> partial on every second plane. Twinning, on the other hand, requires a shear of a/6 <112> on each close-packed plane. The reverse transformation can be effected in a similar way by a/3 (1010) dislocations moving over every other basal plane of the hexagonal phase. Transformation theories2, 7- 12,14 differ in the details of the nucleation of the transformation and the propagation of the partial dislocations from plane to plane. EXPERIMENTAL PROCEDURE Nickel and cobalt rods supplied as 99.999 pct pure were induct ion-melted together under a vacuum of about 10-5 torr in a 97 pct alumina crucible. An alloy containing 30.5 pct Ni was found to have the desired transformation range, with an Ms near -10°C and an j4s in the vicinity of +10O°C. The ingots were swaged to &--in. rod and electron beam zone-leveled in a 10-6 torr vacuum. This procedure resulted in 12-in.-long single fcc crystal rods (designated I to VII) from each of which several tensile specimens of identical orientation were made. Chemical analysis of the bar ends indicated no contamination or gross segregation and no micro segregation was seen in electron micro-probe scans. Tensile specimens with a 9/32-in.-sq by 1-in.-long gage section were spark-machined from the rods and then electropolished or chemically polished to remove the machining damage and to provide a flat surface

Jan 1, 1970

By R. E. Reed-Hill

A simple accurate graphical method for orienting fcc crystals using (111) slip traces on a single surface is described. Solutions placing the pole of the surface in a unit stereographic triangle are obtained using a Wulffnet, a (111) standard projection showing the four (111) planes, and a (111) standard projection ruled into unit stereogmphic triangles. The multiplicity of solutions is described in relation to this method. AN accurate, rapid single-surface technique for orienting fcc crystals, using (111) slip or twin traces, has been a matter of continuing interest, as evidenced by the periodic appearance of papers on this subject.&apos;-4 This note presents a new method possessing some advantages over those previously reported. It is an analog to the technique for hcp metals5 where the solution is based upon a stereographic rotation of the specimen surface on a (0002) standard projection that contains the planes of the possible features that might account for the observed traces. In the hexagonal solution, the axis of rotation is the basal-plane trace in the surface. In the fcc case, the axis of rotation is one of the observed ( 111) slip or twin traces. It has been observed that the solution is greatly facilitated if the indicated movements of the (111) traces during the rotation of the surface are plotted directly on a paper copy of a Wulff net as shown schematically in Fig. 1. The trace selected to represent the axis of rotation is assumed to fall at the north-south poles of the Wulff net. The directions of the other traces are then plotted as points at the proper angles around one-half of the basic circle of the net. The loci of points corresponding to the movements of these traces (directions) during a 90-deg rotation of the surface, about the polar axis of the net, are then easily and accurately drawn by following the appropriate small circles on the Wulff net. The solutions to the problem are obtained with the aid of a (111) standard projection of the (111) planes, see Fig. 2. This is normally a Xerox copy of a carefully drawn master made on high-quality tracing paper. The (111) standard projection is superimposed over the Wulff net and rotated about its center until the points of intersection of the loci of surface traces, drawn on the Wulff net, and the great circles representing the (111) traces, all lie along a common meridian of the Wulff net as demonstrated in Fig. 3. This latter great circle represents a possible position of the surface. The pole of this plane is then plotted on the (111) standard projection. Its location in a unit stereographic triangle may be readily obtained by superimposing (over the standard projection) another tracing paper (111) standard projection subdivided into unit stereographic triangles. The result of this last operation is shown in Fig. 4. MULTIPLICITY OF THE SOLUTIONS The maximum possible number of (111) traces on a single grain surface is four. Any one may be selected as the axis about which the surface is rotated. Corresponding to each such choice are three possible surface-pole orientations, related to each other by a simple 120-deg rotation about the pole of the (111) basic circle. This is a direct result of the threefold symmetry of the (111) standard projection. Since each of the four rotations will normally give a different set of three-pole positions, there are, accordingly, twelve possible solutions. Each of these twelve solutions places the surface pole in the same relative position in a stereographic triangle so that all are crystallo-graphically equivalent. Accordingly, only a single solution is required to obtain a basic orientation of the crystal. It should be noted, however, that the orientations obtained by reflecting* any of these twelve orien- *The reflected orientations may be obtained by a 90-deg rotation of the opposite sense to that shown in Fig. 1. This rotation places the correspond-ing trace loci in the lower hemisphere of the Wulff net rather than in the upper hemisphere. tations through the surface are also possible orientations that could account for the surface traces. Thus, a given set of four traces always corresponds to a pair of basic orientations related by reflection through the specimen surface. This ambiguity can only be re-

Jan 1, 1967

By R. Priestner, R. F. Krause

Solid, cylindrical crystals of a iron have been fractured at 10°K by the simultaneous application of tension and torsion stresses. Thus, a complex distribution of normal (sN) and shear (ss) stresses existed in a cleavage plane at fracture. In every crystal the clearage-plane normal was inclined to the specimen axis, so that a unique point, M*, in the operative cleavage plane was defined where the quantities sn and s2 N + s2 S) were maximized. It is shown that the maxirrzum resolved normal stress on the cleavage plane at fracture decreased as the resolved shear stress in the cleavage plane at M* increased. Thus, a normal stress la?*! for fracture was not satisfied. A fracture law which takes shear stress into account. and which predicts that (s2 N +s2S) should be constant, is to be preferred. However, the data is best represented by a linear dependence of sN on sS, sS which 110 physical significance can be attached. It is suggested that the fracture-nucleating -mechanism is a short-range one. A critical stress law has not yet been unequivocally established for the propagation of cracks in metals. Measurements of the tensile fracture stresses of variously oriented zinc single crystals1 failed to establish the normal stress law expressed by In Eq. [1], sN is the fracture stress, P, resolved normal to the fracture plane, and 0 is the angle between the fracture -plane normal and the stress axis. Similarly, a comprehensive investigation failed to verify the normal stress law for the tensile fracture of a-iron single crystals.&apos; However, a subsequent investigation,3 using iron from the same ingot, presented fracture data which obeyed the normal stress law. It has been shown previously4,5 that the Griffith criterion for fracture6 does not predict such a normal stress law. This result is of particular significance in considering the fracture of metals, such as zinc and iron, which may fail by cleavage. In these metals fracture propagates in a well-defined "cleavage" plane, whether or not an applied stress is normal to it. When the cleavage-plane normal deviates from the direction of application of a uniaxial stress, for example, the crack propagates under the combined action of normal (sN) and shear (ss) stresses. When the presence of a resolved shear stress in the crack plane is taken into account, the Griffith criterion is expressed by4

Jan 1, 1967

By J. Grosso, D. J. Nagel

In many metallurgical studies, it is necessary to reveal the composition and structural properties of materials. Usually this is done by etching, but some substances do not etch well or easily. Anodizing is known to provide an alternate treatment in many cases. In general, this technique is simple, often more sensitive to composition differences than etching, has excellent resolution, and provides variable contrast in those elements and alloys which anodize. Here we report the use of anodizing in diffusion studies in the TiCb system. Fig. 1 shows a cross section of the diffusion zone in a TiCb couple. The anodizing has clearly revealed both composition and crystallographic features. The maximum bulk penetration of the titanium into the columbium is marked by a sharp line because of the steep concentration gradient. The titanium grain size and orientation differences are also evident. Variation in the grain size reflects the gradually decreasing columbium concentration.

Jan 1, 1967

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.&apos;8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By G. W. Toop

In a recent publication,31 Darken has derived an equation to describe thermodynamic behavior in ternary metallic solutions with compositions near pure component 1: Eq. [I] is understood to be a general equation, consistent with the ternary Gibbs-Duhem equation, which is proposed as a logical formalism in view of observed behavior in some binary metallic solutions31&apos;32 rich In Eq. and am are constants obtainable from the 1-2 and 1-3 binaries. The parameter 023 may be determined from measurements on the ternary The purpose of this discussion is to compare Eq. [I) or [3] with other ternary formulations involving binary terms, within the regions of validity of Eqs. [I], [2], and [3]. First, the ternary point is considered to be at the intersection of two composition paths, one with constant N1 and another with constant N2/N3 as shown in Fig. 10. The terms in Eq. [3] may be related to the binary points shown by multiplying the first term on the right-hand side of Eq. [3] by N2 (1) /l -N1, the second term by the third term by and the fourth term by each multiplier being unity: It should be noted here that no suggestion has been made that either the binary or the ternary systems form regular solutions. However, Eq. [5] and hence Eq. [3] shows that the contribution made to the ternary excess free energy from the 1-2 and 1-3 binaries has the same form as for a regular ternary system.1 Before considering the term a23 for the above case, a second geometrical relationship is examined with the ternary point at the intersect ion of three composition paths with constant N1/N2, N2/N3, and Nl/N3, respectively, as shown in Fig. 11. For this geometry, ternary values of NZ and N3 in terms of the binary values shown may be substituted into Eq. [I]. Then by making use of identities of the form Eq. [6] contains terms that are similar to those in a ternary regular solution formulation34 based on the geometry shown in Fig. 11. Although at finite concentrations, unless the 1-2 and 1-3 binaries form

Jan 1, 1968

By Akio Suzuki, P. G. Wahlbeck

AS a part of a study of the vaporization of transition metal-chalcogen systems, the vaporization reactions for the Ti-Se system have been studied. In order to establish vaporization reactions it is important to determine the identity of vapor species in equilibrium with the condensed phases. In some cases, it is possible to deduce the identity of vapor species through observations of composition change of the condensed phase with which the vapor is in equilibrium. Determination of vapor species in equilibrium with condensed phases should precede vapor-pressure measurements and is necessary for proper thermodynamic analysis of vapor-pressure data. Bear and McTag-gart&apos; reported that vacuum heating ot TiSea at 950°C produced a residue with a composition of 1.7 Se/Ti atomic ratio units. Analyses of condensed phases existing for the Ti-Se system have been performed by Bernusset,2"4 Gron-vold and Langmyhr,5 Hahn and Ness,&apos; and Ehrlich.~ Results and conclusions of two types of experiments are described herein: 1) experiments where samples of known composition were vaporized followed by chemical analysis of residues and 2) experiments where the vapor species were identified by means of a mass spectrometer. Experimental Section. Sarnple Preparation. Samples of TiSe2 were prepared in a sealed, evacuated quartz ampule by heating to 1000°C stoichiometric amounts of selenium of 99.999+ pct purity obtained from the American Smelting and Refining Co. and titanium of 99.2 pct purity obtained from A. D. Mackay, Inc. After heating, the sample was ground and reheated to insure homogeneity. Samples containing less selenium than TiSez were prepared by mixing amounts of titanium powder and TiSez appropriate for the desired composition; the titanium and TiSez mixture was heated in the same manner as described for TiSe2. Analyses of titanium selenide samples contained in quartz crucibles were performed by gravimetric oxidation in oxygen at 800°C; the products of the oxidation were solid TiOz and gaseous Se02. The mass of the original sample and the mass of TiOn determined the Se/Ti atomic ratio. The sample of TiSen used in these experiments had a composition of 2.04 Se/Ti atomic ratio units. The compositions for all samples reported were analyzed by this method. Va/!orization Experiments. Samples of titanium selenides were vaporized in tungsten Knudsen crucibles. Some vaporization experiments were carried out in glass vacuum lines followed by chemical analyses of residues, and some vaporization experiments were performed with a Bendjx mass spectrometer as described previously.8

Jan 1, 1967

By T. E. Scott, O. G. Koepke

DURING research currently in progress the need arose for interplanar angles and planar spacings to analyze crystallographic data obtained from hcp yttrium. In the absence of such existing information, a program was written in Fortran-11 language and processed on an IBM 7074 computer. The program and results have been assembled in report form to make them generally available.&apos; Of the possible combinations of, only those most frequently encountered were employed. The ranges of h, k, and 1 involved were: However, not all combinations and permutations of the above appear in the tabulation because redundancies occur in several cases. Nevertheless, fifteen types of planes and all their equivalent planes have been included, giving a total of 109 sets of Miller-Bravais indices.

Jan 1, 1967

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man&apos;s&apos; solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By G. R. St. Pierre, L. M. Adelsberg, R. Speiser

OXIDE platelets have been observed&apos;-3 in oxidized tantalum adjacent to the metal-oxide interface, Fig. 1. The origin and identity of the platelets are important with respect to the proposal of an acceptable mechanism of tantalum oxidation. At reaction temperatures below 750°C, it has been established that the platelets

Jan 1, 1967

By R. A. Oriani

The partial molal volume of hydrogen is one of the parameters that describe the elastic interaction between the solute and the stress fields about inclusions, dislocations, and cracks. As such the partial molal volume is probably of importance in the elucidation of phenomena such as hydrogen embrittlement and hydrogen yield point. A knowledge of this quantity would also be helpful in thinking about the state of dissolved hydrogen in iron. However, because of the very low lattice solubility of hydrogen in iron the usual ways of determining the lattice expansion are not practicable. It is therefore of interest to apply the thermodynamics of stressed bodies to two sets of measurements of the effect of elastic stress upon the permeability of hydrogen in order to deduce a value of the partial molal volume, VH, of hydrogen dissolved in a iron. Beck ..&apos; and previously de Kazinczy, observed that a uniaxial tensile stress increases the permeability of hydrogen in iron and in various steels. Beck et 01. employed Armco iron and A.I.S.I. 4340 steel, whereas de Kazinczy used a steel the composition of which was 0.13 C, 0.23 Si, 0.46 Mn, 0.006 P, and 0.038 S. Upon releasing the stress the permeability increment disappeared if the stress was below the elastic limit. Both investigators employed cathodic charging to introduce the hydrogen. de Kazinczy measured the permeation through a thin-walled tube by collecting the gas, whereas Beck et al. measured the permeation through sheets of various thicknesses by a very sensitive electrochemical technique. Both investigators measured the steady-state permeation at constant rate of hydrogen ion discharge, and Beck measured in addition the hydrogen diffusivity by a time-lag technique which is independent of the boundary conditions. Beck et al. and de Kazinczy found a linear relationship between log (J,/Jo) and the stress, where Ju/Jo is the ratio of the flux of hydrogen when the metal is under uniaxial tensile stress, a, to the flux under zero stress, for the same temperature and charging current. Beck et al. found in addition that the diffusivity of hydrogen is not changed by stress. Both investigators concluded that the observed change in permeability is due to an increase in hydrogen concentration, and furthermore that the increase in concentration is due directly to the thermodynamic effect of stress upon concentration. Accepting this assessment of the situation for reasons given below, one may use the equation3j4 in order to evaluate I/H, the partial molal volume of hydrogen. This equation is valid for the domain of a/E «¦ 1 (where E is the Young&apos;s modulus) and under the assumption that hydrogen expands the lattice isotrop-ically. From the data of Beck el al, one calculates V7H - 2.0 cu cm per g-atom, and from those of de Kazinczy one obtains 1.8 cu cm per g-atom. That the increase of concentration with stress is indeed of thermodynamic origin is attested to by the facts that the experimental results conform to the thermodynamic relation, Eq. [I], and that the results are the same whether a pure iron1 or each of two different steels172 is used. Neither of these facts wou1.d necessarily be expected if the effect of stress were, rather, to increase the ratio kn/k, of the kinetic factors of the following competing reactions: H(ads) — H (dissolved) Such a change of kinetics at the surface could be an alternative explanation of the effect of stress on the permeability. Although this writer does not deem this explanation to be the correct one for the reasons given above, it must be admitted that unambiguous proof that the phenomenon has a thermodynamic origin does not yet exist. Two kinds of experiments may be suggested. One is to plate a variety of metals on the input surface of the steel and repeat the stress experiment at a variety of hydrogen charging currents. The other is to employ somewhat thicker specimens in order to be able to apply uniaxial compressive stress. Eq. [I] shows that ln(c,/c,) depends on the sign of the stress, but it is difficult to see a physical basis for which k2/kl would depend on the sign of a. The present value of V^ in a iron agrees with phragmen&apos;s5 estimate, which he based on comparisons with the lattice expansion by hydrogen of titanium, zir-

Jan 1, 1967

By M. Garfinkle

LITERATURE data1&apos;3 have suggested that the resolved shear stress necessary to initiate slip in a particular slip system in tungsten single crystals is strongly dependent on the tensile orientation of the crystals. This orientation dependence is contrary to the critical resolved shear stress criterion. Because the Schmid factors for slip on particular {110}( I l l), {112}(Ill), or {123}(111) slip systems in a (100) oriented tungsten crystal are virtually identical to the respective Schmid factors for a (110) oriented crystal, slip should initiate on the same system in both orientations, independent of the values of the critical resolved shear stresses. Thus, it would be expected that, for a critical resolved shear stress model to hold, the proportional-limit stress for these two orientations must be similar. The expectation of similar proportional -limit stresses has not been borne out by reported experimental observations. Rose et nl.&apos; reported that the proportional-limit stress for crystals near the (110) orientation was 92,000 psi, approximately three times that of (100) oriented crystals (31,000 psi). Garlick and probst2 reported greater than a fourfold difference. Most recently, Beardmore and ~ull~ examined tungsten crystals with orientations along the edge of the standard stereographic triangle and showed a gradual increase in proportional-limit stress from 28,000 psi for the (100) orientation to 93,000 psi for the (110) orientation. Again, the difference was more than threefold. As has been emphasized by these investigators, the apparent gross variation of proportional-limit stress with orientation precludes any meaningful analysis of slip mechanics using a simple critical resolved shear stress relation. The purpose of the present communication is to report that, by use of refined strain-measuring techniques, the proportional-limit stresses for the (100) and (110) orientations are quite similar. Obviously, to determine accurately the value of the proportional-limit stress, which is by definition the stress at which nonlinear stress-strain behavior first occurs, the method of measuring strain must be capable of high accuracy. The investigators cited used as the measured elongation the crosshead displacement of the tensile machine. This method, however, introduces extraneous strain contributions from the load train. Because these extraneous contributions are considerable in the initial portions of loading (as has been well-documented in the literature) the proportional-limit stress measurement, dependent on the deviation of a line from linearity, can be significantly affected. During the course of a recent study, room-temperature strain was measured directly on several (100)-and (110)-oriented tensile specimens axially oriented within 5 deg of the desired direction. Each specimen was fitted with two foil strain gages mounted on opposite sides of the 0.08-in.-diam reduced section. The tensile specimens were loaded at a crosshead speed of 0.01 in. per min on an Instron Universal Testing Machine. Strain was monitored through an external bridge circuit in which the specimen strain gages comprised two arms. The bridge output was recorded against the applied load. A strain of 2 x 10"" could be readily detected by this method. Some specimens were subjected to conventional loading while the load for others was cycled between zero and continually increasing values until the first deviation from linearity was observed. The results of these methods were similar, and the stress at which nonlinear behavior occurred was considered the proportional-limit stress. The proportional-limit stresses measured in this study are approximately 5000 and 6500 psi for the ( 100) - and ( 110) -oriented crystals, respectively, a range of values almost a magnitude less than those reported previously. Representative curves are presented in Fig. 1. Because of the nature of the measurements made, the point of departure of a line from linearity is often debatable. While the load-strain curve for the (100) -oriented crystals made a relatively abrupt deviation from linearity, the curve for the (110) -oriented crystal was more gradual, so that the actual point of tangency may be at a lower load than reported. Thus, the difference in values for the proportional-

Jan 1, 1967

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed&apos;-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,&apos;~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967

By B. Chalmers, S. Wojciechowski

THE structure of the equiaxed zone of several A1-Cu samples mechanically stirred during unidirectional solidification was examined. The stirring was produced by rotary oscillation of the mold about its vertical axis.&apos; It was found that in Some samples the structure is not of the same type over the whole of the equiaxed zone; it consists of regions with two different etching responses. Fig. 1 shows this structure in a Al-1 wt pct ku sample. The lighter etching regions with a coarse structure form something like a network and the darker etching regions with a finer structure can be observed as the continuation of the coarse structure inside this network. The difference in size and shape of the dendrite branches (they are rounded in the coarser structure) is similar to that found by Williamson and Chalmers in ice crystals solidified in undercooled water: when the amount of undercooling was small, the ice crystals were more rounded and coarser than these solidified with a larger amount of undercooling.&apos; It seems justified to conclude that the observed structure resulted from solidification under different thermal conditions: the coarser structure solidified first out of the "purer" liquid and with a smaller amount of undercooling and the finer was formed later out of solute-enriched liquid under conditions of much more rapid heat extraction. A considerable change in the heat flow conditions at the later stages of solidification can be easily understood by taking into account that the coarser crystals form a continuous network and the amount of trapped liquid is relatively small; hence the contribution of latent heat is much smaller in the later stages of solidification. The difference in structure and etching characteristic reflects a difference in composition between these two regions. It was found that the darker etching re- gions are harder (30.4 to 31.3 HV5) than the lighter etching ones (25 to 26 HV5). A similar type of structure was found in a A1-4 wt pct Cu sample grown by Czochralski method. Fig. 2 shows the structure in the lower part of a sample grown slowly and then decanted by a rapid removing of the sample from the melt. In a few places trapped liquid solidified in the same manner as in the sample shown in Fig. 1.

Jan 1, 1968