Search Documents

By O. J. Neslage, R. W. Jenkins

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today's wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By R. W. Jenkins, O. J. Neslage

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today's wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By John S. Brown

IN 1925 the writer undertook a detailed statistical study of all producing areas in the Joplin district as a basis for evaluating programs and measuring objectives. For this purpose, the published figures in the yearly volumes of Mineral Resources were used, supplemented for earlier years by publications of the Missouri Geological Survey and other local and less official sources. When all else failed, the available data were projected backward to hazard a reasonable guess as to the unrecorded early output of important areas. Fortunately, the proportion of such prehistory production is not a large factor in any of the totals. These results were used during the next few years to measure the relative importance of various producing areas and to predict the peak period of development of the all-important Picher field. For the purpose of this review, the charts have been completed to the end of 1950. During World War 11, the U. S. Bureau of Mines became interested in a similar study and issued comprehensive statistical tabulations of data up to 1945 ( Info. Circular 7383), which have been checked against the figures used herein. This tabulation, however, does not include all the earlier data used by the writer nor does it offer any estimates of the wholly unrecorded era in the beginnings of the earlier camps. The area covered in this study is shown in Fig. 1 on which are indicated the relative location and approximate outlines of the principal producing camps. This also shows the approximate yield to date of each major camp in terms of combined lead and zinc concentrates. The output of zinc concentrates is roughly seven times that of lead. Hence, the economy of the district has depended primarily on the price of zinc, with lead as an important byproduct. Over much of the productive period, lead concentrates averaged about twice the value of zinc concentrates per ton, and in certain mines or areas the proportion of lead to zinc was substantially above average. The Joplin district is largely flat prairie but is partly moderately dissected, partially wooded land with a relief generally less than 100 ft. The rocks are almost flat-lying, nearly parallel to the surface, and the chief ore formation is the Mississippian Boone limestone, including its cherty phases. This formation either outcrops in the producing areas or is covered by a thin veneer of Pennsylvanian shales. Virtually all the ore occurs within 400 ft of the surface, and a large part at less than 300 ft in depth. Most of the land was divided into small farms or town lots before mineral development; tracts seldom exceeded 160 acres, and averaged considerably less. Mineral rights followed the surface ownership, segregation was rare, and a system of leasing for mineral development became well established early in the region's history, many landowners deriving small to sizable fortunes from royalties. Because of the shal-lowness of the ore and other factors, prospecting and mining was cheaper than in almost any comparable mining district in the United States. This situation, coupled with the widely divided land ownership, offered a fertile field for promoters and speculators and led to the rise of many small mining concerns. Only in its later history, under stern economic compulsion, has control tended to centralize in a few companies. Under these conditions, any important new discovery or successful development had much the effect of a gold rush or an oil boom. Every property in the area was leased quickly, promptly drilled, and, if ore was found, it was soon on the market. Many companies and individuals participated, and the average producing lease-hold probably was about 40 acres in extent. Any important field thus was attacked by anywhere from 10 to 100 or more producers. Production zoomed, eventually steadied or wavered, and ultimately subsided, leaving a desolation of tailings mountains, cave-ins, empty housing, and wreckage. The object of this paper is to depict the pattern of this process, so far as metal production is concerned, and to note the way in which it reacted to economic and political pressures. Production Charts In Fig. 2 is charted the production record, in tons of lead and zinc concentrates combined, of eight of the principal camps, which together account for approximately 99 pct of the total district production, over the years from 1870 to 1950. This period covers all but the very minor beginning of mining history. Two important camps are divided by state lines; hence, it has been necessary to combine production records for the two portions, based on estimates that may be slightly in error. Certain camps are sub-dividable into important units for which separate figures are available in whole or in part and have been charted as fractions of the major unit. The corresponding price of zinc is shown above all the charts. Three camps, Aurora, Neck City, and Galena, show a remarkably symmetrical graphic pattern, which is interpreted as the norm. The curves rise steeply to a peak, level off for an irregular interval, and then drop sharply to zero on a slope corresponding roughly to that covered by the initial rise. The three portions of these charts seem appropriately characterized by the designations of youth, maturity, and decline. On the whole, with some irregularities, the production in each of the three periods seems to be almost equal. A fourth camp, Granby, fails to conform to the normal pattern. It exhibits a very long period of reasonably uniform, stabilized production corresponding to maturity, followed by a rather precipitate decline. Its youth is hidden in the era of prehistory. This habit of steady, long-continued production at an even keel is attributable to the fact that this camp, more than any other, was controlled largely by a single principal owner at any given period over most of its history and this permitted the imposition

Jan 1, 1952

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore exploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composition laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a' run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, variations are functions of distance. Hence. in either case, variations along the hole are of greater effect than across it. Let us examine Fig 1 briefly to observe a cross section of a unit of depth of a typical diamond drill hole. If we neglect radial change in chemical composition, which we have seen is small compared to lengthwise variation, we can see that if core recovery was 100 pct, the core and its surrounding area, which would be recovered as cuttings (assuming 100 pct sludge recovery), must analyze the same if the sampling is perfect. This is the foundation of this paper, namely, that if core recovery is complete we may assume that the core constitutes as nearly as possible a perfect sample of the ground drilled. Now let us pass to the methods of weighting core and sludge in the final analysis and then develop each in turn. One might employ core analyses only, sludge analyses only, or apportion the influence of each by one of several methods. The most common apportionment is by direct proportion to relative theoretical vol- ' ume occupied by each component in the cylinder hollowed out by the drill, known as the Longyear formula. Another logical treatment would be to consider core and sludge in the final analysis according to the weight of each recovered. This procedure was elaborately set forth and refined by R. S. Moeh1man.l Then to be sure that we have embraced all the possibilities, we must admit that some other method or methods may be devised empirically or by mathematical maneuvers. Should a drill machine be capable of recovering 100 pct of the core in all types of rock, certainly core alone need be analyzed and no complicated mathematics are required; but although some companies have had fair success in obtaining high percentages of core in certain homogeneous ores on the Mar-quette Range, their same methods have proved disappointing on the Menominee, Cuyuna, and Gogebic Ranges where the iron formation often varies widely from flinty chert beds interstratified with soft hematite to wholly leached ore material composed of an unpredictable mixture of hematite and limonite with occasional zones of sugary, recrystallized chert. In spite of numerous mechanical improvements in core barrels, few drilling programs can count on complete core recovery. The sludge alone might be analyzed but for practical reasons this is inadvisable when core is obtained due to the numerous opportunities for contaminating or losing portions of the cuttings. The Longyear formula involves a weighting of the core and sludge in proportion to the theoretical volume of each, that is, where the volume of the core recovered is one-third of the total cubic volume of the cylindrical hole made by the drill, the analysis of the core is given one-third of the weight in the final analysis. This approach to

Jan 1, 1950

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

By Verne D. Johnston

ALTHOUGH the stocks of Lake Superior iron ore on dock or at furnaces at the beginning of the year were about 6,000,000 tons less than at the beginning of 1938, the steel industry was operating at only 52 1/2 per cent of capacity and continued at approximately this rate to about Aug. 1. Consequently the iron mines in the Lake Superior district during the winter and spring period were almost all on a curtailed production basis, governed mostly by the needs of the communities rather than by anticipation of ore demands. Many of these properties gave extra employment by prosecuting heavy strip- ping programs, and the underground mines by shaft sinking and rock development. All underground mines re- turned to full operation in September, mostly two-shift, five days per week. A few operated the sixth day. The ship- ping schedules were increased so that the actual delivery for the year exceeded early expectations by about 20 per cent. Final Lake shipments were slightly in excess of 45,000,000 gross tons.

Jan 1, 1940

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply. Because of the importance of tin in the world economy, and because of the fact that little is generally known in this country regarding the methods of recovering the tin in Malaya, it is believed that a short description of the industry, as carried on there, may be of interest to many of the readers. In addition you may be interested in the effect of the Japanese occupation, subsequent recovery of the properties and conditions existing at that time. The Malay Peninsula lies at the southeast tip of Asia. Singapore, a British colony, is situated on a small island at the southern end of the peninsula. It is a city of nearly a million population, an important world port, the site of a large British naval base and of one of the tin smelters. The Federation of Malaya consists of nine states, plus Penang, Malacca, and other small areas formerly part of the Straits Settlements, and it now covers the entire peninsula. The civil administration is controlled by the British. A constitution was adopted recently after reaching agreement with the Malay Sultans of the various states, who retain control of religious matters. The Capital is at Kuala Lumpur, a city of about 200,000 population, 250 miles north of Singapore and about half way to Penang. The country covers an area of 51,000 square miles, an area about equal to that of Florida and about one third that of California. It has a population of about seven million consisting of Malays, Chinese, East Indians, and a relatively small number of Europeans. The principal products are tin and rubber. There are over three million acres of planted rubber. The country is not self-supporting agriculturally as about one third of the necessary food supplies is imported. Rice is the principal food of the Asiatic population and some of the recent unrest is caused by a shortage of rice and the consequent high price. Good highways have been built through the settled part of the country. A railway, Government owned, extends from Singapore northward through the entire peninsula. The climate is tropical but health conditions are good for a tropical country. I was in Malaya from 1939 until January 1942, during the time of the simultaneous air attacks on Pearl Harbor, Manila, Hongkong, and Singa-

Jan 1, 1950

By A. D. Hughes

C. W. MERRILL*—Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably. a matter of vital interest. Your Chairman, Mr. Romanowitz, in his introduction, referred to the fact that I had been a member of the United States delegations to the three meetings of the International Tin Study Group. Some cominents on the Group's objectives and deliberations may be of interest. When it appeared that the International Tin Committee, the prewar producer's cartel, might soon revive its operations and extend its control agreement beyond the expiration date of Dec. 31, 1946, the United States Government became interested in some kind of an international trade organization concerned with tin which would give the consumers' interest equal representation with the producers' interests. An international meeting was called in London in October 1946 to consider this problem. I did not attend that meeting hut the result of the meeting was the organization of the International 'Tin Study Group which

Jan 1, 1950

By Bernard York, John J. Reed

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability. THE investigation described in this paper is a continuation of a project begun in 1946 by Bernard York and W. E. Bush. .The experimental method used in the investigation involves the hydrostatic loading of a model mine opening to failure. Most investigators agree that this loading closely approaches actual conditions in very deep mines. The conditions are further idealized by using an essentially isotropic model material. The experiments consist of casting 8-in. plaster cubes, or 8-in. diam cylinders 8-in. long, having a relatively small uniform section hole passing through their centers. After thorough drying, the models are jacketed in a flexible plastic bag and loaded hydrostatically with water in a closed vessel. At about 300 to 500 lb per sq in. pressure the central opening fails. The fracture pattern resulting from opening failure is studied in a plane normal to the longitudinal axis of the opening. The model block is sawed through its center after loading to expose this plane and to eliminate the possibility of end effect. By changing

Jan 1, 1954

By Bernard York, John J. Reed

W. 0. Philbrook (Carnegie Institute of Technology, Phila.)—Mr. DeVaney's paper is a valuable addition to the growing technology of the magnetic roasting of lean iron ores. His furnace is ingeniously designed to permit close control of the process and to achieve high thermal efficiency by counter-current heat exchange and the withdrawal of both solid and gaseous products at relatively low temperatures. The principle of using a lean reducing gas to avoid over-reduction of the ore even at high operating temperatures (for rapid reaction rate) is thoroughly sound. The gas analyses and flow rates reported, however, are internally incon- sistent and render suspect any details of a heat balance based upon them. While it is entirely proper to consider the entrant gas as a reagent and to account only for the heat evolved by consuming a portion of the gas, many operators are accustomed to a heat balance using the total calorific value of the reagent supplied; and comparison of heat balances made with different bases of calculation can be quite misleading. Since Mr. DeVaney's paper is likely to be cited frequently in future discussions of magnetic roasting processes, it seems worth while to point out the internal discrepancies and to give alternate values of heat requirements for different bases of calculation.

Jan 1, 1954

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By J. D. Bateman

At Giant Yellowknife, where high grade gold-bearing orebodies are highly irregular in shape, geology has been applied extensively to the mining of ore. The classical functions of the mine geologist in the fields of exploration and mine development have been extended to guide ore extraction, ensuring "clean" mining and effectively reducing waste dilution. THE property of Giant Yellowknife Gold M.ines Ltd. is situated west of Yellowknife Bay on the north shore of Great Slave Lake, a distance of 600 air miles north of Edmonton, Alberta. The Giant claims were staked in 1935, the company was formed in 1937, and the main orebody system was disclosed by diamond drilling in 1944 following a geological study of the property by A. S. Dadson,* Consulting Geologist for the company. Production began in 1948 at the rate of 200 tons per day and, during 1950, reached a daily rate of 425 tons. During the first 3 years of operation a total of 366,000 tons was milled with an average grade of 0.79 oz of gold per ton. Work is in progress with an expansion to 700 tons per day in view. A descriptive account of the geology and gold-bearing shear zone has appeared previously.* The rock formations in the vicinity of Yellowknife Bay have been subjected to protracted pre-Cambrian tectonic deformation culminating in a series of late faults having a cumulative horizontal displacement exceeding 11 miles. The Giant property is underlain by part of an Archean sequence, several miles thick, consisting of basic volcanic flows and minor intercalated tuffs. The volcanic succession forms the west limb of a major syncline, the flows facing east, but overturned on Giant property to dip west at 65" to 75". Orebodies are confined to shear zones up to 200 ft in width, which were formed along early thrust faults. The shear zones assume fold-like attitudes, the larger of which have an amplitude of several hundred feet. The rock formations beyond the limits of the zone of shearing do not reflect the simulated folds, the axes of which are within a few degrees of the strike of the flows. The schistosity and most of the planar elements in both the shear zones and the orebodies dip west • A. S. Dadson and J. D. Bateman: Structural Geology of Camdian Ore Deposits, Can. Inst. Min. Met. Jubilee Volume (1948), PP 273-283. at angles between 65" and 75", generally corresponding to the dip of the flows. The planar elements within the shear zone system thus dip more or less constantly west whether the shear zone is flat, vertical, or expressed as east or west dipping limbs. The shear zones reflect the deformation and alteration of the basic volcanic flows into chlorite schists which, in most places, have undergone metasomatic replacement to form chlorite-sericite-carbonate schists or sericite schists. The boundaries between the shear zones and country rock, although often gradational, usually can be defined within a few feet or even inches as they are expressed by the limits of metasomatic alteration. Orebodies may occupy a small or large proportion of the shear zone and, although they generally conform to the shape of the zone, their morphology is much more complex. Ore boundaries in some instances are sharp and can be delineated with a chalk line; but more generally, a large proportion of the ore boundaries is not visually obvious and can be determined only by the perception acquired by the geological mapping of ore or study of drill cores. Ore shoots in fold-like attitudes may transect the planar elements of the shear zone at any angle; yet the schistosity within the ore shoot may be coincident with that in the enclosing shear zone. Thus it is clear that problems may arise in the delineation of mining boundaries. Ore generally consists of 20 pct or more quartz with ferruginous carbonates in sericite schist deposited in two dominant stages. The earlier stage limits of quartz with carbonate, pyrite, and very fine-grained arsenopyrite in lenses and bands. The later stage consists of quartz-carbonate lodes, in

Jan 1, 1952

By J. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies. THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.'-" This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications. Geology The geology of the Picher mining field is similar to that of the entire Tri-State district because the sedimentary horizons that are found here are found throughout the district, and the ore bodies in the respective horizons have similar characteristics. The beds that contain the ore bodies in the Picher field are illustrated and described in fig. 2. The five unconformities found in the mines of the Picher field are indicated on the geologic section, fig. 2. The unconformity shown at the base of Meramec (B bed) is relatively unimportant since B bed was mostly eroded from the area of the Picher field before the Chester beds were deposited. B bed has been observed in the cuttings from only a few churn drill holes. The Pennsylvanian (Cherokee shale) formation is the top horizon found in the Picher mining field. It has been eroded from the southeastern part of the field, but because of the regional dip of the sedimentary beds to the west, it attains thicknesses of 100 ft to 200 ft along the west edge of the field. It is 200 ft to 300 ft thick in the Miami trough. It was deposited on the Boone limestone surface, which contained relatively few shallow erosion channels and very few depressions. Subsequent to the deposition of the shale, solution of limestone from underlying limestone horizons by circulating solutions caused the overlying beds, including the Cherokee shale, to slump into the larger openings formed by the solution and removal of the limestone. Chert The origin of the chert in the Tri-State district has been a controversial subject among geologists. Tarr7 advocated a syngenetic origin for the chert, postulating that it formed from colloidal silica deposited in the Mississippian seas. Leith, Dake and Leighton' argued in favor of silicification of erosion

Jan 1, 1951

By J. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies. THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.'-" This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications. Geology The geology of the Picher mining field is similar to that of the entire Tri-State district because the sedimentary horizons that are found here are found throughout the district, and the ore bodies in the respective horizons have similar characteristics. The beds that contain the ore bodies in the Picher field are illustrated and described in fig. 2. The five unconformities found in the mines of the Picher field are indicated on the geologic section, fig. 2. The unconformity shown at the base of Meramec (B bed) is relatively unimportant since B bed was mostly eroded from the area of the Picher field before the Chester beds were deposited. B bed has been observed in the cuttings from only a few churn drill holes. The Pennsylvanian (Cherokee shale) formation is the top horizon found in the Picher mining field. It has been eroded from the southeastern part of the field, but because of the regional dip of the sedimentary beds to the west, it attains thicknesses of 100 ft to 200 ft along the west edge of the field. It is 200 ft to 300 ft thick in the Miami trough. It was deposited on the Boone limestone surface, which contained relatively few shallow erosion channels and very few depressions. Subsequent to the deposition of the shale, solution of limestone from underlying limestone horizons by circulating solutions caused the overlying beds, including the Cherokee shale, to slump into the larger openings formed by the solution and removal of the limestone. Chert The origin of the chert in the Tri-State district has been a controversial subject among geologists. Tarr7 advocated a syngenetic origin for the chert, postulating that it formed from colloidal silica deposited in the Mississippian seas. Leith, Dake and Leighton' argued in favor of silicification of erosion

Jan 1, 1951

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35" to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum. THE Bunker Hill mine, since its discovery in 1885, has steadily produced a high grade of lead-silver-zinc ore. By the end of 1952 over 21,000,000 tons of this high-grade ore had been produced by square-set mining, and reserves in the mine continue to be very satisfactory both as to quantity and grade. For many years prior to 1941, mine production and mill capacity had been 1200 tons of feed per day. Closely adjacent to the mill, and stored behind dikes, coarse jig tailings had been impounded during the time preceding the advent of fine grinding and selective flotation. When manpower became short in 1941 and sink-and-float preconcentration was proved successful, mill capacity was increased to 1800 tons per day to treat these jig tailings economically. By 1946, because the supply of jig tailings was limited, underground exploration was started to discover and prove ore reserves of low-grade material which could be mined by an appropriate bulk mining method. During the years of square-set mining many possible areas of low-grade mineralization had been observed. One chosen for the first exploration work was sufficiently remote from active mining areas so that subsidence, if an ore-body were proved, would cause no problem. Also, old adits and workings were still open and in good enough condition so that exploration in the mineralized zone could be started with a minimum of preparatory work. In 1948 an orebody was proved of sufficient tonnage, of a grade about 2 pct Zn, 0.5 oz Ag, and 1.0 pct Pb. It was decided to use block-caving, the only appropriate mining method by which this grade of ore could be economically recovered. Exploration for additional reserves in other areas of the mine is continuing, but ultimate results are not known at this time. With more sink-and-float capacity, larger ball mills, and more flotation machines, mill capacity was increased to 3000 tons per day, permitting the mining of ore in the square-set area at a maximum rate not usually achieved, because of the scarcity of labor. Increased mill capacity also permits block caving and the mining of jig tailings at variable rates to keep mill feed up to 3000 tons per day. Fortunately the three types of feed are amenable to the same mill circuit and reagents for recovery of Pb and Zn. For example, during the first 10 months of 1952 square sets produced 827 tons per day, block-caving 1421 tons per day, and jig tailings 643 tons per day, an average daily production of 2891 tons for all three products. Exploration had proved the existence of an ore-body 1000 ft long and 165 ft wide in horizontal section, see Fig. 1. Company engineers were concerned only with the vertical extension, about 300 ft, from an old level to the surface. Much of this almost outcropped, Fig. 2. The ore lies in the hanging wall of a major fault of the Bunker Hill mine, standing at 65" in one end of the zone and separated from the fault by a wedge of waste, see Fig. 3. This wedge pinches out near the center of the zone, at which point the ore dips 45", lying nearly on the fault, Fig. 4. The remaining portion lies on the fault and conforms to the fault dip of 35", Fig. 5. Open-pit mining for the top of the ore was considered, but since the ore zone dipped into and under the mountains, adverse waste-to-ore ratios precluded use of this method. The ore occurs in massive quartzite of sufficient strength to support untimbered drifts, crosscuts, and raises. Zones of weakness in the quartzite are bedding, jointing, and small faults or slips. The mineralization, which occurs as small stringers of sphalerite and galena as well as pyrite, creates another line of weakness. The mineral veins or veinlets in themselves are high-grade. Their size and regularity and the amount of barren quartzite by which they are separated determined the limits of mineable ore, which are all assay limits except for the one determined by the major fault. Block 1 Without any background of caving in this type of quartzite, engineers selected the first block on the very steep end of the zone. Compelling reasons prompted this decision. The steep portion of the ore in Block 1 was of the lowest grade, so that if difficulties were encountered no very valuable ore would be lost, while the experience gained might be applied in mining the remaining blocks. A block 200x200 ft was laid out, with four scrams spaced 50 ft apart for drawing and placed at a right angle to the strike. Finger raises were placed in a 25-ft interval grid pattern, with flat undercutting done by crosscuts at the undercut level 25 ft above

Jan 1, 1954

By Adrian E. Ross

Diamond drilling through caving formations at depths greater than ZOO0 ft has long presented serious difficulty, generally solved either by casing or cementing. Casing is permitted only when the resulting smaller hole is acceptable, and cementing is frequently a problem at depth. A new method that injects cement under pressure at the desired location is an aid in diamond drilling deep holes. DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pump- ing process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1953

By Adrian E. Ross

Diamond drilling through caving formations at depths greater than ZOO0 ft has long presented serious difficulty, generally solved either by casing or cementing. Casing is permitted only when the resulting smaller hole is acceptable, and cementing is frequently a problem at depth. A new method that injects cement under pressure at the desired location is an aid in diamond drilling deep holes. DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pump- ing process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1953

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952