Search Documents

By D J. Brake

The correct specification and then selection of primary or major fans for an underground mine is a critical decision not only in terms of fan capital and operating costs, but also safety and reliability which usually has a major impact on mine production. In addition, fan manufacturers may spend tens of thousands of dollars preparing proposals for a purchase enquiry for primary fans especially where they have complete responsibility for the installation (turnkey projects). There are many good reasons to thoroughly and fairly adjudicate fan tenders. This paper describes the process to achieve this starting with the initial fan specification through to the final award.CITATION:Brake, D J, 2017. Fan specification and tender adjudication for mine ventilation engineers with particular reference to turnkey projects, in Proceedings Australian Mine Vent Conference 2017, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By N. P. Reddy, Y. J. Wang

Stall or aerodynamic stall of axial flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1993

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By K. A. Mackinnon

The choice of fan type (axial flow, centrifugal or mixed flow) most suited for a mine ventilation application depends on a number of technical and economic factors. For each project, the relative importance of these factors will vary. It is worthwhile to carry out an assessment on a case by case basis. The paper, by discussing a number of technical and economic factors and their interactions, will provide the ventilation official a methodology to easily and methodically undertake such an assessment.

Aug 1, 2013

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

The spatial and temporal evolution from the porphyry to high-sulphidation epithermal environment can be assessed by integrating new results on such deposits (Arribas et al, 1995; Hedenquist et al, 1998) with past studies of plutonic and porphyry systems (Dilles and Proffett, 1995; Cline, 1995; Shinohara and Hedenquist, 1997; Hedenquist and Richards, 1998). Some time ago, Sillitoe (1973) argued for the nature of the tops and bottoms of porphyry deposits. He concluded that epithermal deposits may form over the tops of some porphyry systems. We can now conclude more confidently what the tops and bottoms of many high-sulphidation ore deposits appeared like while active (Arribas, 1995; Hedenquist, 1995). In addition, we better understand the nature of the zonation of high-sulphidation epithermal systems from the intrusive to surficial environment (Sillitoe, 1999), and how these two styles of ore deposit are related. Geological and geochemical evidence clearly indicates a continuum between these two ore environments. This improved understanding of genesis allows more efficient exploration for these deposits. There are many examples of spatially associated porphyry and epithermal ore deposits. A genetic connection has been suggested by some, and argued against by others. Nowhere is this spatial association better seen than in northern Luzon, Philippines, where the Lepanto high-sulphidation epithermal Cu-Au deposit overlies the Far Southeast (FSE) porphyry Cu-Au resource (Figure 1). Together these mineralised bodies contain a resource of >3.8 M tonnes Cu and >550 tonnes Au. Lepanto was largely mined out in early-1997. Post-war production until 1995 was 0.73 Mt Cu, 115 t Au and 393 t Ag at an average grade of 2.2 per cent Cu, 3.5 g/t Au and 11 g/t Ag. The recent discovery of the adjacent Victoria low-sulphidation quartz-Au-base metal vein deposit, with a resource of >68 tonnes Au (Cuison et al, 1998), illustrates the variety and abundance of mineralisation in the Mankayan district. This district also hosts the Guinaoang porphyry Cu-Au deposit (Sillitoe and Angeles, 1985) and other epithermal vein occurrences (Figure 1). This brief summary reviews the results recently published on the Lepanto-FSE deposits (Arribas et al, 1995; Mancano and Campbell, 1995; Claveria, 1998; Hedenquist et al, 1998), and stresses the evidence for coupling of mineralisation between the porphyry and high-sulphidation epithermal environments.

Jan 1, 1999

By Robert Hopler

In issuing this pamphlet on stump and boulder blasting for the use of farmers, we wish to call attention to the fact that Du Pont High Explosives have been used with universal satisfaction for many years under diverse conditions, and have never failed to give satisfaction in mining, quarrying, roadmaking, blasting stumps and boulders, or for any other work where regard to economy and safety in use is the object.

Jan 1, 2008

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu&apos;s Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

By J. D. Salter

Most diamonds are liberated from their ores by crushing. Diamond and other coarse grained mineral ores require carefully optimised crushing circuits. Recent advances in computer technology have made possible the on-line capture of crushing plant performance data and, hence, the accurate empirical modelling of the crushing process. Such models are used in simulation studies to determine the optimum operating conditions for a given plant. A system is described which allows operating data from mineral treatment processes to be logged. Up to 16 channels of data may be recorded simultaneously at sampling rates in the kiloHertz range per channel. A data storage and analysis procedure is described which allows the system to make full use of its sampling capabilities.

Jan 1, 1987

Rapidly identify unstable mine waste embankments and similar dam structures. Approach Aerial photography, geotechnical instrumentation, and telephone or satellite data transmission are used to supplement walk-around inspect ions. How It Works Embankment stability and other indicators of structural integrity are evaluated using aerial photography, and on-site unattended instruments and data transmitting systems. Evidence of external movement and water seepage is obtained from aerial photography and photogrammetric evaluation techniques. Surface points marked by stake- mounted targets are monitored photographically at time intervals of several weeks or months. Photographic measurements of x, y, and z coordinates of these points are obtained from flying a series of photo-runs over the dam.

Jan 1, 1979

By Peter Hornby, Maurice Craig, Franklin G. Horowitz, Don Bone

We have developed a high-performance, flexible scheme for interpolating multi-dimensional data. The technique can reproduce exactly the results obtained, for example, from Ordinary Kriging and related techniques in 3D, or from Thin-Plate Splines (Briggs&apos; minimum-cuwature algorithm) in 2D. Moreover, com- pared to traditional implementations of these algorithms, our method enjoys large computational-cost savings. The new approach produces an interpolation that obeys a Partial Differential Equation (PDE). The PDE may arise from physically based arguments, but its form can vary widely. It might be specified only implicitly (as through a Model Variogram), or be nonlinear (although a performance penalty could then apply). While a formal equivalence between Kriging and Splines has been known for some time (Matheron, 1980), the present derivation, from radial basis functions, further illuminates this connection. Thus, for example, we can make explicit the PDEs that underlie some of the Model Variograms most often used in Geostatistics. Besides its practical utility, the work thereby ac- quires a theoretical interest.

Jan 1, 1996

By M. Maccagni, J. Nielsen

"The recovery of lead from battery paste has been investigated for a long time and with the use of many different electrolytes. A number of processes have been presented, but none of them reached even the demonstration step. Engitec has developed a new concept for the battery paste electrowinning using a chloride electrolyte fed through a very innovative flow cell. The process has passed the lab and the demo scale and it is ready to be introduced on the market. In this paper, a description of the process will be provided.INTRODUCTIONThe need for improved energy storage systems as well as the introduction of commercially viable electric vehicles is providing a strong compulsion toward the research of new batteries. The lead battery is playing an important role because it is inexpensive, reliable and it is the most recycled material. This last aspect marks the lead acid battery as quite peculiar making it both the primary lead based product and the main raw material for lead production.In the last years the legislative pressure has become very strong and has forced the lead production to react through the introduction of important process innovations and market changes. The dispersive products, such as additives for paints and for fuel as well as bullets, have been practically banned all over the world while the battery market continues to grow. The lead acid battery remains the cheapest and most integrated energy storage system available and is improving to meet the new technical challenges. This is testified by the news coming from the development of new and more efficient lead acid batteries which are confirming their leading position.Unfortunately, the image of lead is very negative in the public opinion and some important actions are required to try changing this sentiment. Among them, better information to the market and users and the introduction of new and cleaner technologies in the production of lead can help."

Jan 1, 2016

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By Donald C. Moore

Introduction Asamera Minerals (US) Inc. and its joint venture partner, Breakwater Resources Ltd., discovered ore grade gold mineralization on their 20 km2 (5000 acre) Wenatchee, WA land position in February 1983. Due to the high grade nature of the discovery ore and the known reserves of ore in the "B Reef&apos; and "B West" zones previously outlined by other companies, a decision was made to construct a mine/mill operation near the known ore occurrences. Further drilling in the discovery area quickly expanded known gold occurrences to more than 3.6 Mt (4 million st) with tentative in-place ore grade of 7 g/t (0.25 oz per st) and minor silver values. Based on existing knowledge of the ore body and the rapidly increasing ore reserve, a decision to build a 1.8-kt/d (2000-stpd) mine and mill complex was made in the second quarter of 1983. A schedule was devised to begin immediate mine development, shaft sinking, environmental and land use permitting, and mill and tailings dam construction (Fig. 1). Meeting the scheduled startup date, April 1, 1985, required a fast track schedule in all areas. To this end, Asamera purchased the Oracle Ridge Partners concentrator. This was an assemblage of new equipment designed for use as a copper concentrator in southern Arizona. The purchase contained all of the major mineral dressing equipment - crushers, screens, rod and ball mills, etc. and an engineering package. It did not include most of the other required items, such as buildings, conveyors, pipelines, tanks, and pumps. At the same time, core samples were sent to two independent process development laboratories for initial flowsheet development. Due to the refractory nature of the carbonaceous ore, cyanide leaching was not feasible. Flotation was selected as the concentration process. Further testing showed that autoclaving of the flotation concentrate followed by cyanidation would result in overall recovery of about 85% gold. A mine manager was hired to begin assembling an operations staff, hire an environmental consulting firm, and begin mine development. Environmental and land use concerns were major obstacles due to the mine&apos;s close proximity to a city of 20,000 people. These concerns had to be rapidly defined so as to mitigate any adverse impacts from and mining processing operations. Baseline data dealing with weather, air and water quality, and sound were measured before start of mine construction. Concentrator and flowsheet development remained static until October 1983 while definition drilling and mine development proceeded. In late October, a process engineer was hired to coordinate development of a process flowsheet, purchase the remainder of the concentrator equipment, prepare a concentrator construction contract, finalize concentrator detail engineering, and combine environmental and process requirements with a tailings dam design. Process development There were only 17 months remaining to mill start up from the hiring date of the process engineer. Therefore, the process flowsheet had to be finalized rapidly. To accomplish this, samples of drill core from the highest grade (and therefore potentially the most commercial) ore zones were sent to an outside metallurgical laboratory to confirm beneficiation tests on the flotation process. Test results again showed that flotation would provide about an 86% gold recovery. Therefore, all further testing was concentrated on flotation and autoclave/cyanidation of flotation concentrates. Focusing on a well known process such as flotation was important in accomplishing the rapid design and construction of the concentrator. If, during these next phases, we were continually changing design concepts, layout, and process flow, the mill startup would have been delayed many months. Once a process flowsheet is selected the process engineer must obtain the process criteria needed to design the beneficiation system. For example, it was known in early December that the Oracle Ridge rod and ball mills were too small to grind 1.8 kt/d (2000 stpd) of Wenatchee ore. A decision had to be made to purchase a large, used ball mill and convert the Oracle Ridge ball mill to a rod mill. The process engineer must be cognizant of the process criteria needed to size and select equipment. If not, the process engineer must use the professional services of the equipment manufacturing companies to review the requirements that the equipment is asked to perform. For the Wenatchee system, this resulted in the adaptation of a ball mill to a rod mill with a weight limit of grinding rods to protect the mill bearings and drive trains. When a decision is required, the process engineer has to present the facts and options in a manner that allows a rapid decision. This information must include costs, equipment availability, and effect on the construction schedule. At the Cannon mine, there were process development details that resulted in decisions similar to the ball mill purchase. These included an increased flotation residence time from eight to 25 minutes, an increased thickener area requirement, a high pressure tailings pumping system, and area constraints in plant layout. All of these decisions had to be timely and required assistance from manufacturers&apos; service engineers, and knowledge of the alternate costs and effects on construction completion. Equipment procurement It was decided in early 1983 to build the ore milling facility with Oracle Ridge equipment, augmenting it with used equipment

Jan 2, 1989

By D. C. Moore

The decision to proceed on a "fast track" construction project is not" without risks as well as rewards. An understanding of some of the risks prior to start of the project will maximize the rewards. This paper describes the research, development, procurement, engineering and construction of the Asamera Minerals cannon Mine concentrator. This fast track project was accomplished in 20 months. Special attention is paid to the risks encountered and the steps taken to ameliorate them.

Jan 1, 1988

Mine Evaluation Engineering , Operational and Social evaluation. Focus is on what opportunities are available. Social ??History ??Past Management Practices ??Community / Available labor force Mining Method / Equipment ??Competent rock ?little support required, no backfill ??Shallow mining ?ramp mining, no shafts or hoisting ??Large scale mining potential ??Simple rock breaking and crushing on surfaceMill Process ??Straightforward gold liberation process Create a Plan / Create a Team Following the feasibility 44-101. Key people were hired and a full operational Business Plan was developed. Focus is on how to get the job done. ??Scoping Study / Pre-Feasibility / Feasibility ??Operational Business Plan ??Hire key people ??Purchase key equipment

May 1, 2006

By Bruce McKinstry

INTRODUCTION In June of 1992, the Bureau of Reclamation, United States Department of the Interior, awarded the contract for construction of the Sixth Water Aqueduct to the Fedrick-Redpath Joint Venture. This aqueduct, a segment of the Diamond Fork Power System, Central Utah Project, diverts water from Strawberry Reservoir into Sixth Water Creek and, when complete, will replace the old Strawberry Tunnel which was driven in the early 1900&apos;s. The new aqueduct is being built primarily as a result of deterioration of the old tunnel, but will also have a higher capacity and more positive control than the old tunnel as well as the capability to incorporate a turbine into the system at a later date. The Fedrick-Redpath Joint Venture is comprised of C.R. Fedrick, Inc. of Novato, California and J.S. Redpath Corporation of Tempe, Arizona. Fedrick, with its experience in pipelines and heavy construction, will construct the 4200 ft surface pipeline and flow control structure; Redpath, the managing partner, performed the underground work consisting of a 600 ft vertical shaft and 3300 ft tunnel. The project is located in the Uintah National Forest, approximately 20 miles east of Provo, Utah at a mean elevation of 7000 feet above sea level.

Jan 1, 1995