Search Documents

By W Wu

The prospect of discrete element modelling (DEM) being used as an everyday design tool for transfer chutes in the iron ore mining industry is becoming more and more probable. However, much care needs to be taken to ensure accurate results are obtained. Whilst there are many publications in industry portraying the potential of DEM, there is little evidence of where it has been validated against a real set of experimental results. The purpose of this investigation was to gauge whether the incorporation of the physical properties of a specific bulk material at the DEM pre-processing stage can yield visually and numerically accurate simulations for a simple flow case. Effects such as irregular particle shapes, varying frictional properties and coefficients of restitution, all found through experimentation were investigated. Video analysis was used to compare simulations to real flow cases. It was found the most critical attributes in determining the accuracy of the simulations were particle shape and wall friction. Keeping the particle-to-wall friction factor constant was not sufficient to describe the flow accurately. But by introducing the varying effects of wall friction with consolidation stress, the correct results were simulated.

Jan 1, 2007

By Manfred K. Walther

"Tests were conducted on instrumented plates cast in the Abex Experimental Foundry to compare recorded solidification histories with results computed for corresponding models simulated with the C.A.S.T. program. The first plate was cast of low alloy steel and the second of carbon steel with a graphite chill at one end. Both were cast in molds of bonded silica sand. Temperature histories were recorded in the castings, molds and chill. Exceptionally good agreement was achieved between computed and experimental data. Other investigators will find the results useful as a benchmark against which they can compare the results of their own calculations.IntroductionSince the early 1970's our foundry engineers have used both two- and three-dimensional versions of the G.A.S.T. program to gain knowledge of the solidification process [1,2,3]. Study of the computed data gave insight as to how the rigging and risering of specific castings might be changed or adjusted to improve quality and yield. New schemes based on such analyses were then recommended for implementation on the foundry floor. The degree of success of the new practice was subsequently evaluated after the part had been poured, shaken out and examined. Similar conditions were noted in the sectioned castings whenever porosity and voids had been predicted by the computations. Appropriate modifications, when found successful in the model, were applied to the process. This led to a reduction, if not complete elimination, of the defects. Such results gave credence to the use of these programs as an aid in the production of better castings.Earlier investigations on simple shapes revealed excellent correlation between output derived with the G.A.S.T. program and exact solutions. Results also compared favorably with data calculated using other codes as reported in the literature [4] and summarized in the Appendix. However, since the computer program had not been verified by direct experiment, it was decided to run instrumented tests to check the theoretical predictions with actual measurements."

Jan 1, 1986

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

By R. W. Charles

The Los Alamos National Laboratory, under the sponsorship of the U.S. Department of Energy; is involved with laboratory and field experiments to assist in development of the Hot Dry Rock concept of geothermal energy. The field program consists of experiments in which hot rock of low permeability is hydraulically fractured between two wellbores. Water is circulated from one well to the other through the fractured hot rock. Our field experiments are designed to test reservoir engineering parameters such as heat-extraction rates, water-loss rates, flow characteristics including impedance and buoyancy, seismic activity, and fluid chemistry. Laboratory experiments were designed to provide information on the mineral-water reactivity encountered during the field program. Two experimental circulation systems tested the rates of dissolution and alteration during dynamic flow. SOlubil ity of rock in agitated systems was studied. Moreover, pure minerals, samples of the granodiorite from the actual reservoir, and Tijeras Canyon granite have been reacted with distilled water and various solutions of NaCl, NaOH, and Na.CO.. The results of these experimental systems are compared to the observations made in field experiments done within the hot dry rock reservoir at a depth of approxi-mately 3 km where the initial rock temperature was 150 to 200°C.

Jan 1, 1981

By Patrik Fredriksson

Thermodynamic data concerning FeO-containing slags is of importance in ladle refining of steel. With a view to generate a set of reliable and self-consistent thermodynamic data for these slags, experimental determination of the activities of FeO in binary and ternary slags was carried out using the gas equilibration method involving CO-C02-Ar gas mixtures at steelmaking temperatures. The slag samples in Pt crucibles were quenched after the equilibration and subjected to chemical analysis. The thermodynamic activities of "FeO" in the slags were calculated from the experimental data. The results are incorporated into a thermodynamic description of silicate melts in the present laboratory. The model is based on a Temkin-Lumsden approach and is able to compute the thermodynamics of higher order systems from the lower order ones.

Jan 1, 2003

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

"En 1953, se habilita la nueva planta de flotación de cobre en Paragsha, donde el funcionamiento de las soleras tipo Lorain y la producción del mineral pirita lograron buenos resultados. Empero las nuevas condiciones de proceso, limitaron su funcionamiento y costo. Por tal motivo, el objetivo del trabajo se basa en la construcción de una solera de mayor rendimiento y menor costo, modificando su diseño al de una honda contínua. El primer juego de este diseño fue instalado en el molino de cobre Nº 1, sin aún obtener el dato final sobre su rendimiento. Posteriormente se consideró la solera AMSCO, dado que el diseño fue más eficiente y el costo final por tonelada fue menor. Sin embargo, se encontró que el contorno del valle era muy cerrado y las bolas N°4 se alojaban de modo ajustado, formando una solera muy gruesa. En consecuencia, se construyó otro diseño denominada ""Solera de onda abierta contínua"", el cual fue instalado en el molino de cobre N°7, donde la capacidad de molienda es igual de óptima y los costos son menores. Así, se pensó que la solera de una sola honda, es mejor que la de onda contínua puesto que este diseño tiene una sola honda en el centro de cada plancha de la solera. Luego, se diseño un tercer diseño, donde el promedio de vida era mejor. Por ello, de los tres diseños a seleccionar -la solera Lorain con 10 hondas, la solera de una honda con 20 hondas y la solera de honda continua de 30 hondas -, la última demostró ser la más eficiente. De otro lado, se probaron otros diseños de honda contínua con distintas aleaciones como el ""Nihard"", cuyo promedio de vida es entre 14 y15 meses aproximadamente, con el tonelaje actual de aproximadamente 270 000. Concluyendo que la experiencia anterior con solerasNihard en molinos a rodillos de 4 pies de diámetro, el impacto es mayor, obteniéndose en quebrantamiento de soleras a 3/4 grosor, pero que pese a esto, resulta ser superior a cualquier otra solera usada actualmente y en eñ que Paragsha esté 100% con soleras de molinos Nihard, a excepción de las rejillas dada su fragilidad. "

Jul 20, 1957

La influencia de los estudios de adsorción para el beneficio de los minerales, se relaciona con la flotabilidad de las especies minerales, y la perspectiva que se ofrece para el progreso de la metalurgia de concentración. Por ello, el objeto de la investigación se basa en la realización de tales experimentos como búsqueda del dominio de la clase de fenómenos fisico-químicos. Dentro de los métodos usuales de determinación de xantatos por yodo, se buscó hallar la concentración por medio del descenso de la adsorción, para determinar la máxima cantidad de reactivo y encontrar el más adecuado para el mineral. Empero, se reparó que a mayor concentración de colector, se genera mayor adsorción. Asímismo cuando se añade el xantato sobre el mineral con poca agua, la cantidad de reactivo adsorbida es superior, justificándose la ventaja que en procesos industriales significaría acondicionar después del espesamiento. En cuanto a la adsorción de galena oxidada, se observa que mezclando este mineral con un sulfuro de zinc, disminuye la adsorción. Posteriormente se ve cómo la superficie oxidada de la galena, puede alterarse por medio de reactivos, variando el grado de adsorción para los diferentes reactivos colectores de flotación. Finalmente se infiere que la realización de las pruebas pretenden determinar principalmente cuál es el reactivo más adecuado más adecuado para una galena determinada.

Jul 20, 1957

By E. C. Pechin

THE Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

Jan 1, 1874

By T. L. Joseph

LARGE deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore-are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In' view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute-has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the manganese content of manganiferous iron ores in a: form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports. I The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treat-ment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a Y2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

By D. W. Frommer, M. M. Fine

Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.1 The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.2 The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's 3. At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's.

Jan 3, 1959

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By Scott Dupont

Due to the scarcity of miners, and the necessity of decreasing the cost of mining, the Phelps-Dodge Corporation, Stag Canon Branch, at Dawson, [ ] New Mexico, decided to try, by various methods of mining, to increase the tonnage of coal mined per man, per day. With this in view, they first tried mining on a 250-foot face, maintaining the track at the face and using six to eight men shovel- [ ] ling. These men were able to aver age from ten to twelve tons each per, day when they were loading, but with

Jan 1, 1926

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost,1 are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger2 was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil3 have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo- physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electro- chemical circles since 1910.4

Jan 3, 1957

By S. Radacina Rusu

The satellite-based global positioning system (GPS) has significantly changed the way site operations are carried out in surface mining. The GPS has impacted safety, productivity, fleet efficiency, and maintenance practices. However, no comparable global localization system exists for underground mines. This paper discusses recent work in the application of ideas from the mobile robotics research community to the problem of real-time vehicle positioning in underground drift networks. Related previous work recently focused on the creation of globally consistent 2D maps of underground environments that possess sufficient detail to be used for underground localization. Our current work entails the development of a GPS-like system for mobile mining equipment, with results given from both laboratory and field experiments.

May 1, 2011

By D. A. Stout

Mr. Chairman and Members of the Rocky Mountain Coal Mining Institute: Your Secretary has asked me to write upon a subject' which is a most interesting one, and which has a very wide scope. In view of the great need for further decreasing costs at its coal mines, the Colorado Fuel and Iron Company began early in 1924 to experiment with methods of mining which had not previously been. tried out at its mines, and which were selected because of the greater possibilities for the concentration of the work, better grouping of workmen, and increased tonnage per workman, with a resultant increased efficiency, better supervision, and lowered costs. Because of the great competition of the day, means and methods must be provided by which fewer mines can be made to produce larger tonnages and at a lower cost. Western physical conditions are such as to make our problems far more complicated and not so easy of solution as compared to many of the eastern fields where conditions are more favorable for the operation of the mines. The dry condition of our Western mines on account of a relatively low humidity, and with additional gaseous conditions, makes the problem still more difficult to solve. A study of new methods was necessary before adoption, and this was particularly true of the method of extracting the coal. Where mechanical means are used, particularly in the coking coal mines of this state, due consideration must be given to the type, and machines or conveyors should not be installed solely on the basis of their performance elsewhere, without the knowledge of local influencing factors. In trying out the newer methods of extraction at our mines, very careful consideration has been given to the question of safety and the adoption of any new methods must provide adequate means of protection to employes, and be approved by' the State Coal Mine Inspector. In any large industry there are a few outstanding operating costs, and usually the leading ones in their order are labor cost, material cost, and power cost. The things which we, hope to accomplish: 1. Reduce labor costs. 2. Reduce material costs. 3. Reduce power costs by the con 4. Reduce the amount of powder used per ton of coal produced. 5. Increase the lump percentage (particularly at the domestic mines). 6. Reduce accidents and annual compensation payment. 7. Reduce haulage costs. 8. Reduce cost for track work. 9. Reduce cost for timber and timbering, and increase the recovery of timber at a considerable additional saving. 10. Reduce the brushing costs. 11. Reduce the amount of rock hauled to the outside. 12. Reduce the cost for drainage. 13. Reduce the cost for ventilating. 14. Reduce cost of inspection and supervision. 15. Reduce the cost for shot firing. 16. Reduction of number of working places. 17. Grouping of men with increased sociability. 18. Increased tonnage per man. 19. Reduction in total number men employed. In the consideration of the methods used and now working successfully, there were three points which were considered outstanding, to make them wholly successful: ventilation, roof control, and transportation. For making the experiments, those mines were selected where conditions

Jan 1, 1925

By A. C. Watts

FOR several years, a mine in Colorado experienced considerable trouble from small fires caused by the blasting of coal. Although a well-known make of permissible powder was used, it was first thought that the powder ignited gas that might be present and that this, in turn, set fire to line brattices or to the coal. Experiments were, therefore, conducted with another make of powder, but the results convinced the superintendent of the mine, Robt. Williams, Jr., that the fires were not caused by the powder but by the high-voltage electric current used for detonating the shots. The mine "makes" gas very freely, giving off from three-fourths to a million cubic feet of methane per 24 hours. The coal is a good grade bituminous of a very free burning quality. Electric shot-firing from the outside after all men and animals were outside had been practiced for a number of years. The shooting circuit was connected with the main power circuit at the mouth of each entry. Shooting circuit switches were mounted in boxes, which were kept locked with the handle of the switch, in open position, showing through the bottom of the box. The door of the box could not be shut and locked when the shooting switch was closed. At the entrance to each room, or working place, a small switch, called the miner's switch, was placed on the shooting line. It was the duty of the miner, when entering his place at the beginning of the shift, to see that this switch was open and that it was kept open until he left the place at the end of the shift to go out of the mine. Grounded return was used for main power lines. The current was 500 volts, direct current, with 100 to 300 amp. The nearest working face was 9600 ft. from the shot-firers' switch outside the mine and the most remote working face was 2 ½ miles. The various working faces were scattered over a wide area between these two points.

Jan 9, 1925

By Robert Goodrich

THERE is a small area about Murray where bedded gold quartz veins occur in Prichard slate. The ore taken from the upper levels, during the early days, was free milling and was treated by stamp milling and amalgamation. There was likewise a considerable placer working. The report is current that tungsten (scheelite) was encountered, which interfered with the amalgamation in the stamp mills and which, in placering, collected in the riffles in the sluice boxes and. clogged them. Consequently, in the quartz mines, the scheelite, when encountered, was rejected, being thrown into the waste, sometimes inside the mine and at other times outside on the clump. The free surface ores became worked out and as the ore in depth became pyritic and rebellious to amalgamation the mines closed down. Last spring tungsten ore brought a high price, near $80 per unit, 60 per cent. W03 and up. This so stimulated the output of tungsten ore that old clumps were explored and waste stored in the mines was gone over. Tungsten was likewise mined from virgin ground. So the district produced quite heavily for a time. The condition now is different. The price is not so high, about $20 per unit W03, which makes profits questionable when mining in new ground. The accumulations from early clay mining have been exhausted and the output has greatly declined. The Golden Chest mine was the heaviest producer of tungsten. The months of June and July were spent at this mine studying the problem. Since the mine had produced both gold and tungsten, we looked forward to the problem of recovering both from what might be called a gold-tungsten ore. A study of the Golden Chest vein showed this not to be so there. While gold ore and tungsten ore come from the same vein, the tungsten ore is confined to a more or less disturbed or distorted portion

Jan 8, 1917

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

By L R. Sousa, M He

Rock burst is common in deep underground excavations and is characterised by a violent ejection of block rocks from excavation walls. It is critical to understand the phenomenon of rock burst and particularly the failure mechanism. Laboratory experiments are one of the ways. For that purpose, a rock burst laboratory test system was developed at the State Key Laboratory for Geomechanics and Deep Underground Engineering at the China University of Mining and Technology, Beijing. A true triaxial test system, designated the Deep Underground Rock Burst Analogue Test Machine, was developed, which can transfer a stress state from three-direction-compression on six surfaces to the compression on five surfaces with one set free. The rock burst experimental system comprises an acquisition of acoustic emission signals, a high-speed recording in order to accurately record the kinetic characteristics of rock fragments ejected during a rock burst event and the possibility of infrared thermography showing the surface temperature of the samples. In this paper, analyses of typical results from rock burst tests are presented with a description of the obtained results. The mechanisms of rock burst are illustrated, and a rock burst classification is proposed based on these laboratory tests. For the control of rock burst, the constant resistance, large deformation (CRLD) bolt or anchor is presented for accommodating the large displacement of surrounding rock masses and absorbing the impact of the sudden release of rock burst while outputting a constant resistant force in response to the external load. The CRLD bolt or anchor has had practical applications in underground mines. Finally, in situ tests performed in a tunnel at Qingshui coalmine, China, are analysed in detail.CITATION:He, M and Sousa, L R, 2014. Experiments on rock burst and its control, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 19–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014