Search Documents

By S. F. Walsh

The San Manuel Oxide Pit is located within the subsidence boundaries of Magma Copper Company's block caving operation. Ground conditions offer a constant blasting challenge and vary from hard, competent crystalline rock to widely spaced fracturing in a sedimentary conglomerate. A successful drilling and blasting program has undergone several changes since mining commenced in 1985 and continues to be developed. This paper discusses the site specific progress made with the drilling and blasting program from selection of feasibility parameters to current practice. Topics discussed include controlled blasting, use Of high energy blasting agents, charge decking, blast casting, as well as standard drill and blast techniques.

Jan 1, 1988

By R. J. Sterrett

To the average mine operator, the implementation of environmental regulations are viewed as a drain on the profitability of the mine. Since the birth of environmental awareness in the late 1960's, which led to the passage of the National Environmental Policy Act (NEPA) in 1969, and through the publicity brought about by the discovery of Love Canal in 1978, the public are clamoring for increased environmental protection. It should be emphasized that the concern regarding the issues of the handling and disposal of nuclear and toxic wastes is not limited to a few overzealous environmental advocates. Toxic waste issues have "grass roots" interest and support. A reflection of this support has been the passage of key pieces of federal legislation. . Of particular interest are the following acts: Clean Water, Toxic Substances Control, Surface Mine Land Reclamation, the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The last act is often referred to as "Superfund". Both RCRA and CERCLA have been re-authorized and amended, and in their re-authorization they have been substantially strengthened. Of the last two pieces of legislation, RCRA is the most powerful in that it governs the handling of hazardous wastes from "birth to grave". CERCLA was established to cleanup abandoned waste sites which are threatening human health or the environment. These cleanups can be undertaken by the government and then billed back to the previous owners or to the disposers at the sites.

Jan 1, 1988

By W. E. Cobb

Mining companies, as developers of natural resources, are being forced to deal with the potential long-term liabilities of past, present, and future mining operations. As discussed in a previous paper (Cobb, et al., 1987), these liabilities can include solid waste disposal corrective action programs (state or federal actions), Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), (Superfund) (state or federal actions), or natural resource damage claims (typically filed by state agencies and provisions specified in CERCLA). These potential liabilities are very real, and should dramatically impact the way a company views its exploration and development programs, and operating mines.

Jan 1, 1988

By David G. Chedgy, Edward A. Zawadzki, Robert D. Stoessner

Extensive research and testing in commercial facilities has clearly demonstrated that heavy medium cyclones are the most effective process for cleaning a 0.6 x 0.15mm (28 x 100 Mesh) coal at low separating gravities, less than 1.35. This paper describes testing performed to deter- mine system characteristics at these lower gravities and the type of circuitry required to maximize performance. The results of these studies include both pilot and commercial scale tests of cleaning 0.6 x 015mm (28 x100M) coal.

Jan 1, 1988

By P. J. Bethell

This paper reviews current fine coal cleaning circuitry, including water washing cyclones, tabling and froth flotation. It goes on to examine possible future beneficiation based on emerging technologies. Circuits considered include those incorporating spirals, fine heavy medium cycloning, hydrosizers and column flotation.

Jan 1, 1988

By A. G. Wylie

The dimensions and shape of both airborne and bulk amphibole-asbestos fibers are different from those of cleavage fragments of the amphiboles. These differences are related to the mineralogical properties unique to the habit of asbestos. These properties include the fibrillar structure, small fibrill widths and distinctive crystallographic faces of fibrills. Criteria for distinguishing amphibole cleavage fragments from amphibole-asbestos include mineralogical proper-ties observable in bulk samples and the dimensions of particles collected on air filters.

Jan 1, 1988

By S. E. Clay, P. R. Taylor

A physical model for the diffusion and flow of gases through porous solids, which accounts for the random nature of individual gas molecules moving through a solid of definite structure, has been formulated. The model was solved using' the Monte-Carlo technique. It was then used to evaluate specific constants related to the dusty gas model and to describe the gas-porous solid diffusion phenomena. Experimental results were used to validate the stochastic model.

Jan 1, 1988

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By Gordon C. Gutrath

Queenstake Resources Ltd. has been exploring and mining alluvial gold deposits in the Yukon Territory and British Columbia since 1980. The five mines in production produced, in 1987, a total of 13,222 ounces. This paper will briefly review Queenstake's exploration program, property descriptions and mining methods, environmental concerns and a comparison of costs. (Sueenstake has been successful in developing a cash flow base from these operations that provide the capital for the acquisition and exploration of new, and hopefully, larger scale gold producers. NOTE: The historic alluvial mining unit of ounces per cubic yard and English units of measurement have been used throughout this paper. Dollars are Canadian unless otherwise noted.

Jan 1, 1988

By K. J. Sollman

With an ongoing concern for safety and health in the workplace, NYCO® requested three medical evaluations be undertaken to study possible health hazards of wollastonite. Two of the evaluations were conducted by the National Institute of Occupational Safety and Health (NIOSH). One was in 1976 (Ref. 1), and the second in 1982 (Ref. 2). The aim of the two studies was to answer the following two questions: 1. Do wollastonite workers exhibit more respiratory abnormalities than workers not exposed to wollastonite? 2. Is there a relationship between prevalence of respiratory abnormalities and accumulated expo-sure time to wollastonite?

Jan 1, 1988

By W. Bassow

In June 1972, when the United Nations convened its historic Conference on the Human Environment, only 24 countries had established government agencies with environmental responsibilities. Of these, 11 were in the industrialized world, 13 in the Third World. By 1985, the number had dramatically surged to a world-wide total of 145, with the greatest growth among the developing countries to 110, an increase of almost 1000%.

Jan 1, 1988

By M. Szatkowski

The studies conducted by Laplante and coworkers (1983,1984) with flotation of galena and quartz, showed that the rate of flotation reaches a maximum value for a certain intermediate value of the air flow rate. A similar, though less pronounced, effect of the air flow rate on the selectivity was also observed. Luttrell and coworkers (1985) showed that the size of air bubbles has a significant effect on both rate and selectivity of coal flotation. These two studies used flotation tests in which no froth layer was formed. This note describes effects of the air flow rate and bubble size on the rate constant and selectivity of coal flotation, using a mechanical laboratory machine with a froth layer allowed to form. Experimental A raw, dry ground Illinois coal was used in flotation tests. The size distribution and ash content of the samples are : Particle size (µm) Weight (%) Ash (%) +600 4.30 41.7 600/200 43.05 19.0 200/74 22.25 16.0 - 74 30.40 24.0 average 20.8 No. 2 fuel oil with a concentration of 200 g/t of feed and M.IBC with concentrations of 11, 22, and 33 mg/L of pulp (128, 256, 384 g/t, respectively) were used as flotation reagents. Tap water with a natural pH of 7.0 to 7.8 was used throughout the tests. No other reagents were used. The starting concentration of coal in the pulp was 86 g/L. A standard flotation machine with the pulp volume of 5 L was used in experiments. Three different air flow rates were employed, resulting in three air escape velocity values of 14, 30, and 70 cm/min. The air escape velocity (AEV) was calculated as the ratio of air flow rate (Qa) to the slurry surface (Ss) in the machine. For a comparison, the upper limit of air escape velocity values used in commercial size flotation machines is between 70 and 100 cm/min (WEMCO, 1983). A machine consisting of a generator of fine bubbles and a separatory column, described elsewhere (Szatkowski and Freyberger, 1985), was used for some tests where bubble size lower than that generated in the standard machines was required. Prior to a flotation test, a batch of coal was mixed with water in the flotation cell for at least 10 minutes to ensure that all coal was thoroughly wet. Then the specified amount of fuel oil was added and the pulp was conditioned for five minutes. The specified amount of MIBC was added 15 seconds before the end of conditioning. After air flow was opened, flotation products were collected for 0 to 30, 30 to 60, and 60 to 120 second intervals. Content of the combustible material in samples was determined by subtracting the ash content from 100%. A photographic technique was used to determine initial distributions of bubble size generated by the flotation machines. Bubbles generated in water containing the prescribed amount of the frother but no solids were photographed against a black background. The average diameter and standard deviation were then calculated for each set of flotation conditions. The method gives results reproducible within k 5% of the average bubble size. Table 1 contains information about the measured bubble size distributions expressed by the average bubble diameter (Db) and the standard deviation ( SD ) . Results and discussion The general formula for calculating the flotation selectivity is: o = recovery of coal/recovery of ash (1)

Jan 1, 1988

By Richard R. Klimpel

INTRODUCTION The process of froth flotation as a means of upgrading the quality of coal by removing water and/or ash and/or pyrite has been receiving increasing attention since the 1960's by the world-wide coal industry. Historically, coal preparation practice has involved the use of primarily gravity based separation techniques, screening, and/or water washing in removing the larger fragments of inert material from coarse raw feed coal. The preparation, handling, and cleaning of raw coal finer than 500 micrometers was deliberately avoided. Most often the fine coal that was produced would be judiciously incorporated into the bulk of the larger sized cleaned coal product or simply discarded. Since the 1960's and accelerating in the 19701s, the desirability of performing some type of coal cleaning or upgrading on the finer raw coal feed materials has been increasing. There are several apparent industrial incentives for implementing fine coal ((500 urn) processing alternatives including the gradually increasing value of the normally lost fine coal product; the additional amounts of fine coal being produced due to changes in mining techniques; the need to appropriately dewater and upgrade fine coal streams in order to meet increasingly stringent environmental regulations on water quality. storage of fines, etc.; the increasing need to lower undesired sulfur and ash contents in some coal end-use applications; and the increasing development of speciality coal use processes that require inherently finer and cleaner coal particles such as in gasification, liquefaction, fuel injection, etc. Looking at the over 70 years of mineral oriented fine particle separation successes at the industrial level, the use of froth flotation in fine coal would also seem to be a natural process to utilize at the industrial level. In the world of strictly mineral processing technology and, more importantly in the world of mineral commodity economics, there are clearly a number of advantages to using froth flotation that are well documented and universally accepted. These include: the relatively low capital and space requirements required when compared to other process options available to upgrade minerals; the extreme flexibility inherent to the froth flotation process both with regard to throughput and differences in raw feed characteristics; the general availability of a wide range of equipment sizes and reliable suppliers of equipment; and the general availability of appropriate and relatively cheap chemicals that are the major driving forces behind mineral flotation. Just how has the implementation of froth flotation fared in coal upgrading over the last 20 years? It is towards answering this question that this paper will be oriented. As such, the discussion will be somewhat philosophical. The comments offered are based on the personal experiences of this author who has worked in the basic side of inventing new flotation chemistry and flotation analysis techniques with the major overriding goal of implementing this new technology successfully at the industrial level in both coal and mineral flotation throughout much of the world. This paper is not intended to be a complete reference to all published scientific work on the subject of industrial froth flotation of coal. As a brief background to what will be expanded upon in this paper, the author would like to offer the following summary comments: 1) the industrial practice of fine coal froth flotation is qualitatively similar but quantitatively different than industrial mineral froth flotation when viewed from either research considerations, operating viewpoints or economic evaluation criteria; 2) it is clearly possible to invent and/or develop new technology (such as new chemistry and/or equipment) that can do statistically better than current plant practice in well-controlled tests in either coal or mineral flotation circuits; 3) there is so much inherent variability to the raw feed coal streams and other operating parameters that even if there is a documented technical incentive to implement some new piece of technology, the people, instrumentation and control methodology required are often simply not available or not economic unless the potential payoff is quite large.

Jan 1, 1988

By A. C. T. Bigg

Heavy media separation is one of a number of ore-concentration techniques for coarse? feed which, when the ore is amenable, offers economic advantages in the mining stage and/or the processing stage. In mining, simpler and cheaper methods may be used if a greater proportion of waste material can be included in the mining blocks that can later be re-moved efficiently at a coarse size. In the mill, pre-concentration can mean considerable savings in capital and operating costs by down-scaling of equipment sizes particularly in the grinding section. Conversely, throughput may be increased using the equipment already in-stalled in the concentrator.

Jan 1, 1988

By B. V. Close

Surface mining regulations together with mine and reclamation planning require collection of large amounts of geologic and hydrologic data for both new and existing mines. Recently developed microcomputer software facilitates the integration of this information from computer databases into ground-water flow models. The databases are used to identify areas which require dewatering and/or depressurizing and for generating contour maps of aquifer parameters. Gridded versions of these contour maps are incorporated into finite difference ground-water flow models which are used to design dewatering and depressurizing well fields and to estimate the effects of ground-water pumping and pit progression on local ground-water levels.

Jan 1, 1988

By C. N. Bensley, S. K. Nicol

The major developments in fine coal processing in Australia are reviewed. Emphasis is placed on the approaches taken by various Australian coal producers to improve the recovery of the coarse size fractions (minus 0.5 plus 0.25mm) and upgrade the selectivity of flotation at ultrafine sizes (minus 0.075mm). The effects on fine coal preparation of flotation circuit changes, the influence of physical and chemical variables on coarse coal flotation and the impact of spiral concentrators and column flotation, are discussed. Reference is also made to the development of oil agglomeration technology for the treatment of fine coal refuse and some of the factors which have led to its current demise.

Jan 1, 1988

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By Peter T. Luckie

Coal represents 80% of the fuel reserves of this country, yet only 20% of the fuel consumption. In order to change this ridiculous situation, a realistic coal utilization roadmap needs to be drawn to show how we go from where we are to where we want to be. The completion of the roadways will require the building of research bridges. The research bridges on the coal processing section of the superhighway should be built to process 500pm by 100pm rather than 25pm by 0 raw coal . Particular emphasis should be on middlings processing and total plant performance. The superhighway should be layed out by a team of fuel, coal preparation and mining engineers.

Jan 1, 1988

By W. A. Lawruk, L. J. Wilson, D. E. Stief

The Tower mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine and its operation, application, and performance for wet grinding.

Jan 1, 1988

By D. S. Dick

Over the last few years, new methods to characterize the flow properties of bulk solids have been developed. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field conditions. In addition, the effect of large particles on a material's flow properties (cohesive strength, bulk density, wall friction) can be determined as well as the effects of various additives such as Freeze Conditioning Agents. New developments have also taken place in terms of devices to improve the reliability of solids flow. Much attention has been paid to finding ways to provide a mass flow pattern with relatively shallow hopper walls through the use of inserts. Such devices can also provide reliable in-bin gravity blending of bulk solids and/or completely non-segregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. Many of these developments have direct application in the mining and minerals processing industries. Examples of each will be highlighted.

Jan 1, 1988