Search Documents

By L. Darkwah

The use of explosives in coal mining inevitably results in oversize, midsize and undersize (fines) products due to fragmentation. The oversize can be broken into smaller sizes by further processing. However, the undersize have a negative affect on the efficiency of a mining operation. Therefore, limiting the amount of fines can be economically crucial. This paper concerns investigations aimed at reducing fines generation in coal mining. Inherent fractures were identified as one of sources of fines generation. This paper is centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs, which are evaluated in terms of the fines generated.

Jan 1, 1998

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By J. M. Mutmansky

This paper outlines patterns of methane emission in both longwall and room-and-pillar operations and the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane drainage system will be discussed as well as the costs related to the production of coal. The important issue of production slowdowns and gas outs will also be discussed as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems will be made as well as justification for more intensive economic analysis of coalbed methane extraction and utilization.

Jan 1, 1998

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

By Hélio Blak

The Paranapanema Group was created in February 1996 when a group formed by the Brazilian pension funds acquired four companies dealing with nonferrous metals. The new Paranapanema Group, basically related to the tin and construction business, became the sole Brazilian primary copper producer, the second zinc producer and one of the most important producers of copper products, mainly tubes and fittings. To put together such different companies, managed before by family groups and with different cultures and principles, was and still is a big challenge. The strategy of developing and consolidating it as an homogeneous group is based in three pillars: an increase in production, quality and technological improvements on products and market mix and a permanent cost reduction program, using all the potential synergies founded.

Jan 1, 1998

By Daniel A. Payne

For many years underground mining in the Sydney Coalfield has suffered from the effects of high horizontal stresses. It is only in the last 15 years that they have come to be recognized, understood, predicted and even avoided. This paper relates experiences in three coal mines in three different seams in the Sydney Coalfield. The effect of the direction of the principal horizontal stress on the direction of drivage of gate roads, access roadways and longwalls is described. Results of a monitoring program to measure the change of magnitude and direction of the principal horizontal stress in the gate roads as a result of longwall mining are also presented as well as the effect of the direction of principal horizontal stress on the shape of sandstone/gas outburst cavities.

Jan 1, 1998

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By A. C. C. Pacheco, L. C. Bertolino, M. L. Torem

On account of geological characteristics, Brazil is a country of large deposits of high quality kaolin, with the larger ones being located in its northern region. In the last years, kaolin beneficiation and production area is receiving great investments, aiming at a high quality kaolin production to be used in the paper industry, mainly intended for the foreign market. After the conclusion of expan- sion programs and with the advent of new production areas, Brazil is very soon expected to come in second place in the kaolin world production ranking.

Jan 1, 1998

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990's to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998

By Ernst Raphael

Mechanical drives of belt conveyor drives have experienced a huge amount of improvements concerning technology, manufacture and product structure that reduced investment and maintenance cost significantly. Most of these improvements were of technological nature in the'70s and '80s of this century; whereas, the present decade requires products that meet technical excellence as well as commercial advantages such as quick delivery, low cost and reliable spare parts supply. The best approach to meet these requirements is a highly modular and standardized system of reliable components that cover all demands a conveyor drive might require.

Jan 1, 1998

By Kenneth R. Miller

Surface mine equipment operators in the Campbell County region of Wyoming's Powder River Basin have found new ways of solving old problems. Technology, experience, competitive pressures and an increasing grasp of economies of scale have driven mine operators, equipment manufacturers and suppliers to specialization of applications. In economic terms, today's coal price of $4.95/t ($4.50/st) equates to $2.53/t ($2.30/st) in 1980 terms - an incomprehensible value at that time. This article describes some examples of change and adaptation made by Powder River Basin coal operators in overburden stripping equipment and techniques. It focuses on the evolution of the design and use draglines, shovels, trucks, scrapers and dozers.

Jan 1, 1998

By Jeff Hussey

Since 1955, Gaspe Mines has produced 150 Mt (165 million st) of ore averaging 0.9% copper. The ore was mined from two open pits and from underground workings. In 1994, four exploration drill holes discovered a buried porphyry/skarn copper-molybdenum (Cu-Mo) deposit at depths of between 1,000 and 1,700 m (3,280 and 5,580 ft) below the top of Porphyry Mountain. The mineralization and alteration associated with the Porphyry Mountain quartz monzonite does not outcrop. Prior to 1997, about 19,500 m (64,000 ft) of drilling in 12 drill holes had outlined 200 Mt (220 million st) grading 0.73% Cu and 0.08% Mo. Mineralization occurs as veins and disseminations of chalcopyrite and molybdenite.

Jan 1, 1998

By R. S. Austin

One-third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. Properly selected and refined, kaolin is an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By C. Waddell

PDMI mines five different grades of ore. Shovel operators were experiencing problems differentiating one material type from another. In 1997 PDMI decided to try GPS ore control to aid operators in identifying material boundaries. Computer generated ore control maps and GPS data defining the shovels' position is fed to a computer on board the shovel. A monitor, located near the shovel operator, displays material types, their boundaries, and the shovels' position and movement in relation to the mining face. This information has reduced errors in material identification by 50%.

Jan 1, 1998

By Mary Korpi

So now you ask, Where are the transcripts? The well-organized co-chairs, Harry and Mary, did their job. Doug Halbe was active in the audience encouraging people to speak up and keeping everything moving along. So where are they? Were the comments so provocative that they could not be written? Was the profanity so bad (even for miners!) that it couldn't be repeated? It appears that at the first session of the Plant Operators' Symposium a glitch occurred with the recording equipment. Thanks go to everyone who did comment during the dis- cussion period. The People I session had a lot of lively conversation and we are sorry that it will not be printed. However, there is now another reason to hold the plant operators' sessions on a regular basis! Another People session can and will be held in the future.

Jan 1, 1998

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998