Search Documents

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By Gregory A. Hahn

Explorationists and engineers rarely speak the same language. Explorationists are not cognizant of the information that engineers require to make the appropriate choices and decisions. Engineers can- not "translate"geo1ogic parlance and data into information relevant to proper decision making. This often creates a physical and intellectual "rift" between engineers and geologists that inhibits a smooth transition to development. A transition team leader who is grounded in both disciplines can best facilitate integration and communications between the explorationists, who understand the intrinsic attributes of a given deposit, and the engineers, who have to design for extraction and beneficiation of an orebody.

Jan 1, 2001

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By Edward C. Dowling

Dilbert, management mumbo-jumbo, and human resource buzzwords aside, this paper defines corporate culture and why it is important to understand it. The sum of company experience, both good and bad, defines the way people work together. This integration of experience outlines the expected behaviors, or culture, in an organization. Given the competitive pressures inherent to our industry, the dizzying ongoing industry restructuring, and the recognition that behaviors drive effectiveness, the appreciation of an organization&apos;s culture is a prerequisite to meaningful improvement, particularly for those organizations undergoing growth, acquisitions, or mergers.

Jan 1, 2001

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200&apos;, very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 &apos; ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

A number of factors affecting the properties of cemented aggregate fill (CAF), particularly its strength development have been studied through a series of laboratory investigations carried out at the Western Australian School of Mines in the Western Australia in recent years. The outcomes of these investigations indicate that apart from cement dosage, aggregate particle size distribution, aggregate quality, additional fine materials, water salinity, admixture dosage and sample scaling all contribute significantly to the development of cemented aggregate fill strength.

Jan 1, 2001

By Jon Y. Kaneshiro, Stephen J. Navin, Jerry Ostberg

In 1968, the U.S. Bureau of Reclamation awarded S.S. Mullen Construction of Seattle, the Intake Tunnel (488 m by 4 m diameter tunnel) and Pumping Plant No. 1. In1998, the Southern Nevada Water Authority awarded Lake Mead Constructors (Kiewit of Omaha) a parallel New Intake Tunnel (518 m long by 4.6 m diameter tunnel) and Pumping Plant. Both projects provide water to a thirsty Las Vegas. This paper presents a detailed comparison of the two intake tunnels in terms of grout takes and pressures, geologic mapping and rock quality, grout penetration beyond the excavation line, degree of fracture grouting, and groundwater inflow boundary considerations. The paper provides a comparison of grouting techniques and material developments then and now.

Jan 1, 2001

By D. H. McCain

Through a unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT) Center, a video packed, dazzling CD-ROM training program was developed for new miners entering the aggregate industry. Why this product was developed, and why the aggregate industry, will be discussed along with the challenges faced throughout the project. Cooperation from every one involved including MSHA made this the product of which all other training materials in the mining industry will be measured against in the 21st Century. This product&apos;s versatility and wide application makes it a tool that is as critical to a mine&apos;s success as any earth moving machine. Developed with both state and federal grant moneys allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2001

By Lynne Chastain

The Eastern Shoshone and Northern Arapaho tribes of the Wind River Indian Reservation, Wyoming are interested in developing their industrial mineral resources. The U.S. Bureau of Indian Affairs (BIA), Division of Energy and Mineral Resources (DEMR) is assisting the tribes in evaluating the potential of their industrial mineral prospects for development. Gypsum occurs on both sides of the Owl Creek Mountains in the basal portion of the Jurassic Gypsum Springs Formation. The gypsum resources that are being evaluated crop out along the northern flank of the Owl Creek Mountains in the Sweetwater basin, a small topographic sub-basin of the Big Horn Basin. From October 1998, to April 1999, DEMR personnel mapped, sampled, and drilled the southcentral butte within the Sweetwater basin. Samples were analyzed for free and combined water, and major mineral oxides to determine gypsum purity. Gypsum purity averaged 93.6 percent for surface samples and 95.1 percent for drill core samples. The basal portion of the Gypsum Springs Formation is comprised of several beds of gypsum up to 9 feet (2.7 m) thick separated by 0.5 to 2.0 foot (0.15 to 0.61 m) thick lenses of siltstone and limestone. Overall gypsum in the formation ranges from 35 to 90 feet (11 to 27 m) in thickness. A resource of approximately 7 million short tons (st) (6.4 million metric tons [mt]) has been identified.

Jan 1, 2001

By S. C. Langvik

The presentation named &apos;Dewatering of fines by Rotary Vacuum Disc Filters&apos; has an opening why the filtration process is important to the Iron Ore Industry. It goes on to describe the various types of dewatering machines which have been used in this industry in the last 30-40 years, and where the vacuum disc filters now dominates. It presents also the most important design changes which have been made during this period to enhance performance. Further are discussed the principles of filtration and the factors and parameters which influence performance and operating costs. As a closing is presented today&apos;s ideas and thoughts about what can be foreseen of design modifications and improvements in disc filter design in the coming ten years.

Jan 1, 2001

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By James Warner, Peggy Ganse, Glen Smoak, Raymond Henn, Sam Bandimere

Over the past several decades, cement-based grouts using ultrafine cement as are placement for portland cement have begun to gain acceptance as an alternative to chemical solution grouts, however the amount of information currently available on these grouts is limited. For this reason, the authors developed a field testing program to evaluate the penetration capabilities of various ultrafine cement grout mixes. The tests were conducted by injecting sand columns using different portland and ultrafine based grouts, the measuring penetration distances after applying equal injection pressure for the same time period. Results of tests performed in 1999 and 2000 are discussed herein.

Jan 1, 2001

By D. G. Millette, A. J. S. (Sam) Spearing

The design of a cost effective backfill system involves many aspects and various inputs from different engineering disciplines. Backfilling is a very significant mining cost and efforts need to be made in the design stage to maximise efficiency and flexibility whilst minimising costs. The aspects that need to be considered include the following: Required fill performance underground Peak and average fill tonnage requirements Backfill scheduling in the mining cycle Material selection, testing and preliminary costing Plant design and storage needs Infrastructure requirements Implications on surface waste/tailings disposal and costs Total backfill costs In order to produce a cost effective and efficient backfill operation, a multi-disciplinary project team is required that should include the following skills and functions: Mine Planning Rock Engineering Metallurgy Mechanical Engineering Environmental Health and Safety Tailings Disposal/Waste Management This paper discusses the above and indicates important aspects that should be considered.

Jan 1, 2001

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By Clifford O. Hamilton

In both mature and young maintenance workforces, the workforce commonly lacks some of the skills required for their assigned work. We call this the "skills gap." This skills gap usually exists in a new operation because although you may hire qualified maintenance personnel, they more often than not have little if any experience with the specific equipment at the facility. Performance Associates International, Inc., has developed and proven a technique to address the maintenance skills gap that is usually found in a new operation.

Jan 1, 2001

By Alan E. Isaacson

Extensive gravel deposits exist within a six-county area in the mountains surrounding the Salt Lake Valley, and in the mountain ranges to the west. The six-county area includes Davis, Salt Lake, Summit, Tooele, Utah, and Wasatch Counties. The majority of these are beach deposits from prehistoric Lake Bonneville. However, real estate development associated with a projected population increase of 54 percent over the next 20 years is expected to remove most gravel deposits in Salt Lake County from consideration for mining, forcing gravel operations to relocate from eastern Salt Lake Valley to the Oquirrh and Stansbury Mountains farther west. The gravels in these ranges are of lower quality and require additional processing to manufacture asphalt and concrete. Replacing gravel resources along the Wasatch Front with resources in the Oquirrh and Stansbury Mountains over the next 20 years has the potential to increase construction costs by nearly $1 billion. The majority of this cost (82 percent) is the result of increased transportation costs due to longer distances to market. The remainder of the cost is attributable to lower quality gravels that will require additional processing in the manufacture of asphalt and concrete. The following analysis and discussion does not take into consideration the amount of crushed stone that is currently being used in the construction industry in northern Utah, its use as a substitute for lower quality gravels, or as a factor in the base case projection.

Jan 1, 2001

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001