Search Documents

By W. Collingwood, K. V. Raj, S. Bandopadhyay

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in openpit mines is relatively new. Modeling the actual pit geometry of an openpit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an openpit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in openpit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions and turbulence modeling parameterization. An appropriate mesh selection is critical. A detailed discussion of the meshing of the domain of an openpit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (κ-ε), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an openpit and some of the approaches adopted to address these challenges.

Jan 1, 2013

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By C. D. Litton

When methods to prevent the occurrence of fire in underground mines fail, the next line of defense is to rapidly and reliably detect the developing fire, so that subsequent evacuation and control procedures can be safely and successfully implemented. To provide this capability requires an understanding of the operational principles of different types of fire sensors, their merits as well as their limitations, and performance characteristics of the monitoring systems that control and process sensor data; an understanding of how fires develop and the different types of fires that can occur, along with their characteristics and the hazards they present; an understanding of the impact of the mine environment and routine mining activities, not only in terms of these effects on fire sensors but also in terms of the impact of mine ventilation and mine geometry on fire growth, fire characteristics and the detection process. All of these factors are components of the technology of fire detection, and when insufficient knowledge of any of these components exists, the ability to implement adequate mine fire detection systems is diminished. Within the last decade, significant advances have been made in fire detection technology applicable to underground mines. These advances include not only the development of improved sensors and better monitoring systems, but also an expanded understanding of how to deploy sensors, set sensor alert/alarm levels, account for ventilation effects, etc. In addition, there has been an increase in our knowledge of the types of fires that occur, the types of combustibles involved, characteristic times for fire growth and development, the levels of heat, smoke and gas that are produced and the hazards that result. It is the intent of this paper to provide not an overview of current mine fire detection technology and, also, to present data obtained for some smoke sensors that have potential for use in underground mines. The paper will also discuss the data, information and resources that are currently available and seek to identify those areas most in need of further research and development.

Jan 1, 2011

By C. V. Deutsch, J. B. Boisvert, J. L. Deutsch

Data used to build geostatistical models come from a wide variety of sources with potentially differing sample errors and volume supports. Typically all available sample measurements are pooled together for statistical analysis irrespective of the quality of the data. The sample data is used to assess spatial continuity, make local estimates and assess uncertainty. A new methodology is proposed to simplify accounting for samples of differing quality. The result is improved estimates with higher weights assigned to high-quality samples, while low-quality samples receive less influence in resource estimation. A new dimension, d, is introduced and calibrated to account for sample error and/or volume during estimation. The addition of an extra dimension can be easily incorporated in existing kriging or inverse distance workflows. The only additional parameters required are the sample error and volume for each datum. The methodology is demonstrated and the improvement in local accuracy is documented. Extending the dimensionality of the domain to four (three spatial dimensions and the additional d dimension) requires a valid 4D variogram model; therefore, the spherical variogram model is generalized to arbitrary n-dimensions.

Jan 1, 2011

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures by the equipment operators. As part of this effort, the U.S. National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study that determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system that was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels between outside-to-inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system’s efficiency. Tests using particle count instruments performed during nonproduction time periods on both pieces of equipment indicated protection factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By A. Tordoir, S. S. Kanchibotla, W. Rogers, E. Engmann, B. Bisiaux, S. Ako

Blast-induced rock mass displacement can have a significant impact on ore loss and dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of, blasting can lead to significant financial losses due to ore loss and dilution. Ore dilution occurs when waste material is miscategorized as ore and sent for processing or stockpiling, diluting the run-of-mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorized as waste and sent to the waste dumps, thus never being processed and recovered. Extensive research has been conducted at the University of Queensland over the last fifteen years to understand the impact of blast movement on ore loss and dilution. Recent outcomes of this research have led to the development of innovative tools and techniques to measure and model blast movement. These techniques have been implemented at the Ahafo gold mine in Ghana to understand blast movement dynamics and to implement solutions to reduce blast-induced ore loss and dilution. These solutions are validated through controlled trials and have been incorporated into site standard operating procedures.

Jan 1, 2012

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By Yi Luo, Jianwei Cheng, Mingming Li, Lei Xiao

Concealed thermal events in longwall gobs present safety hazards for underground coal miners and can significantly interrupt mining production. The probable causes for such thermal events range from coal oxidation at slightly above ambient temperature to smoldering fires due to spontaneous combustion of the broken coal left in the gobs. Locating such “hot spots” is the key step for planning and implementing mitigation measures to bring such thermal events under control. If a mine section, or even an entire mine, has to be sealed, understanding the status of the sealed mine atmosphere is important for the decisions guiding subsequent actions. The gas composition data obtained through the tube bundle mine atmospheric monitoring system is firsthand information of great value. Fire ratios proposed by various researchers and derived from gas composition data are useful in determining the fire status and even approximating the source locations (Timko and Derick, 2006). However, the applicability of each of these ratios under particular conditions should be carefully evaluated. The use of properly combined fire ratios can enhance the certainty of analysis. The explosibility of a sealed mine atmosphere deserves primary concern for safety reasons during seal construction, idle time and reopening of the sealed area.Mine atmospheric monitoring data from a longwall mine with flame fire have been analyzed. Efforts have been made to identify the possible causes, locations and statuses of these events using the obtained gas data, as well as other ventilation, geological and mining parameters. The effect of injected inert gas to control the events has also been quantified. The explosibility of the sealed atmosphere has been determined using two methods.

Jan 1, 2012

By W. R. Reed, J. D. Potts

This study tests the ability of a new air nozzle system, located under the drill deck shroud, to improve the dust capture of the drill deck shroud. The system consists of three air nozzles supplied with regulated pressurized air and located midway down the shroud in the off-inlet corners of the shroud. Laboratory testing produced operating curves for the system that showed an optimum operating point of 207 kPa (30 psi) and generated respirable dust reductions of 48% to 52% from the drill deck shroud.

Jan 1, 2009

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By Chee S. Theng

As the 2015 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2015 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 338. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME. Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2015 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-focus articles on gold processing, iron ore processing and coal processing. The 2015 Transactions consists of a total of 67 technical papers, encompassing all 22 papers published in 2015 in the Technical Papers Section of Mining Engineering (Vol. 67) and all 29 papers published in 2015 in Minerals & Metallurgical Processing (Vol. 32). Additionally, this volume contains 15 papers and one discussion that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2015 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2015

By D. Lauriski, E. D. Thimons, A. C. Smith, D. C. Fredley

The National Institute for Occupational Safety and Health (NIOSH) and Northwest Barricade LLC (NWB) conducted a study to evaluate the effectiveness of a novel fire blocking gel for use in underground coal mines to extinguish or retard the growth of a coal fire. The gel agent was subjected to controlled laboratory testing to assess its ability to delay coal ignition. It was then evaluated to determine if manual fire hose application could be used to apply the agent to mine roofs and ribs to provide a safe egress for mine rescue teams from a fire area. The gel agent was also evaluated in a water sprinkler system to determine its potential for use in conveyor belt fire suppression systems. The agent was then tested in live-fire exercises to examine its effectiveness in retarding and extinguishing a deep-seated coal fire and wood fire. Lastly, the ability of a mine rescue team to quickly and safely apply the gel agent to a mine entry during a simulated mine fire exercise was determined.

Jan 1, 2011

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water inflows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk.

Jan 1, 2013

By Emily Wortman-Wunder

As the 2009 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2009 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 326. A significant portion of the contribution that we as a society make is the publication of professional and technical papers that contribute to the advancement of scientific knowledge and information transfer. Communication within the mining community is the key to a successful society. Through the information-transfer mechanisms of books, magazines, meetings and electronic media, the technology exchange that is fundamental to the existence of the Society is accomplished. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly satisfies that intent. In keeping with SME’s tradition of promoting technological developments while honoring the past, the 2009 Transactions represents an important milestone. It is the last Transactions to appear as a bound volume. Future volumes will appear as e-books only, with some of the Transactions-only papers appearing online prior to the ebook (exactly what form the new Transactions will take is still in development). The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which we hope will better serve the mining community, especially our international members. This 2009 Transactions of SME, Vol. 326, contains a total of 73 technical papers (510 pages), including all 23 papers (136 pages) that were published in 2009 in the Technical Papers Section of Mining Engineering magazine (Vol. 61) and all 32 papers (232 pages) that were published in 2009 in Minerals & Metallurgical Processing (Vol. 26). In addition, this volume contains 18 papers (142 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 73 technical papers were peer-reviewed and approved. The process of review and publication requires much hard work by authors, reviewers and publications staff. As the 2009 president of SME and on behalf of our members, I would like to extend our gratitude to all whose efforts contributed to the publication of this volume.

Jan 1, 2009

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015