Search Documents

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By C. K. Blair, V. J. Hucka, E. P. Kimball

In central Utah, a coal mining operation is taking place under an 0.5-m (20-in.) pressurized natural gas pipeline. The room-and-pillar method with pillar extraction is being used to extract the coal from the seams. The pillars beneath the pipeline will not be extracted; however, there is a possibility that some subsidence may occur due to pillar failure. To assess possible damages on the pipeline, an attempt has been made to predict subsidence in the area where pillars may collapse. The resultant values of subsidence strain and slope have been used to determine the magnitude of strain, stress, and shear induced in the pipeline. Also, a network of survey points has been installed along the pipeline to detect ground move¬ment that would indicate excessive subsidence.

Jan 1, 1987

By V. J. Hucka

A 0.5 m (20 in) diameter high pressure natural gas pipeline crosses over a coal mine located in Central Utah. Ground movement induced by the mining operation could possibly place excessive strain on the pipeline causing it to rupture. The mining operation extracts coal from two seams using the room and pillar method. The seams are situated one on top of the other and both lie directly under the pipeline. At present, only the upper seam is being mined beneath the pipeline. However, in the future, the mining operation of the lower seam will also affect the pipeline. As would be expected, mining of both coal seams causes surface subsidence. This is especially true when the pillars are extracted during retreat.

Jan 1, 1983

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By L. Korkiala-Tanttu, M. Rinne, Z. Song

Disposal of mine tailings has been recognized as an unavoidable burden of mining companies and local authorities. Conventional methods dispose mine tailings in a passive manner which hardly generates any value from them. On the other hand, growing local communities close to mines need more infrastructures which require great amounts of raw materials. In view of the above mentioned situation, a novel utilization of mine tailings is explored as alternative material for asphalt pavement, in order to extract more value from mine tailings and solve the high cost of pavement material. Inherent physical properties of the mine tailings were first investigated to find out their availability as pavement material. Then test specimens were made as mixture of the mine tailings and other pavement material to be tested in laboratory. The mine tailing materials presented a considerable potential as asphalt filler for low-volume roads. Furthermore, the limitat

Jan 1, 2011

By J. O. Craig Imrie

Mine operations are being squeezed to do more with less. This is not new. But, where do mine operators turn for the next stage of improvement? Many have waged strong wars on the cost reduction front and cut back staff to the bone, yet need more improvement to remain competitive. This paper will outline an approach which a few leading operators have taken. Following the footsteps of manufacturing's view of supply chain management and basic quality management they are reaping the benefits of taking a more holistic process view of their operation. This paper presents summaries of three companies' approaches and the impact which is being felt on the bottom line.

Jan 1, 1999

By K. D. Allen, M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most mining operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most milling operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By Howard L. Hartman

If I told you tonight at the outset that my prognastications for the future of mine ventilation were imparted to me by a palm reader or inspired by a vision, you'd dismiss what I had to say before I said it! If, on the other hand, I told you that my forecasts were the result of an elaborate computer model, derived from a complex algorithm, which in turn relied on finite element analysis -- and the entire projection confirmed by on-site experiments with a turbo hybrid-flow mine fan -- you'd sit up in anticipation and hang on my every word!! All of which places me in a terrible dilemma, because my predictions really lie somewhere in between. My intent is to talk to you out of my background of forty years in mine ventilation, looking ahead to conditions that I expect to prevail in the next fifteen years. You may be curious why I picked an unlikely time span of 55 years for my overview, and my response is that it bridges a career lifetime. "The last forty", of course, corresponds with the period of my professional employment since graduating with a B.S. and M.S. here at Penn State. "The next fifteen" bridges the period I expect (the Lord willing) to remain professionally active -- and coincidently brings us into the beginning of the 21st century. (I must confess to stacking the deck a bit: Since it's infinitely harder to look ahead than to look behind, I purposely minimized the forecast period and maximized the history! Besides, "forty" and "fifteen" have a nice phonetic ring, perfect 20/20 vision sums to "forty", etc., etc.). With these disclaimers, I'll invite you to join me now in a fast 55-year overview of mine ventilation, of necessity limited to a broad-brush treatment of the subject. (After all, this is an after-dinner talk, not a marathon!) In each- segment, I've selected the seven topics that seem to me of paramount importance: in the first part, seven accomplishments in retrospect, and in the last, seven expectations for the future. (The number "seven" needn't confound you, either: In the bible, it signifies "wholeness" or "completeness".))

Jan 1, 1987

By A. R. Bell

Rio Algom Limited are currently undergoing a major expansion of their mining operations in the Elliot Lake area. To date this has involved the increase of output at the Quirke Mine from 4080 to 6350 tonnes per mill day (4500 to 7000 tons), the rehabilitation of the Panel Mine to produce at the rate of 2990 tonnes per mill day (3300 tons) by 1980, and the rehabilitation of the Stanleigh Mine to produce 4540 tonnes per mill day (5000 tons) by 1984. In addition, the planning for the rehabilitation of the Milliken Mine to produce 4990 tonnes per mill day (5500 tons) is now underway. This major expansion is taking place at a time of increasing awareness of occupational health matters and has involved very high capital expenditures and detailed planning related to the ventilation system to endeavour the provision of an acceptable environment. The paper discusses the ventilation systems, established and proposed, and relates them to historical and current data on mine air contaminants.

Jan 1, 1980

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

By Yuuichi Umeki, Yuusaku Tominaga

In order to keep good air condition in any specific branch such as coal face and/or heading in an underground coal mine, effective factors of all the branches with respect to the specified branch have been investigated, using computer simulation. Main results of the paper are as follows; 1) A branch in a network is classified to one of three classes of effectiveness to increase, to decrease and not to change airflow rate in the specific branch by altering aerodynamic resistance in the branch. 2) Distribution of position of branches, belonging to each class, related to a specific branch is one of the macroscopic characteristic of a network which is the inherent property of every network. 3) A relation of the aerodynamic resistances of any two branches to keep a constant airflow rate in the specified branch is shown as a monotonous curve. 4) Ventilation transition diagram with the rate of airflow in the two branches as coordinates, and for different rates of airflow in the specific branch as the parameter, is found to be straight lines. 5) Existing range of airflow rates In the specified branch is given as a parameter in the enclosed area in the ventilation transition diagram. Moreover, an expert system to assist ventilation control using a transition diagram of airflow rate is introduced in this paper.

Jan 1, 1991

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Muhammad O. Rahim

The importance of planning ventilation systems in modern coal mines cannot be overemphasized. Interconnected entries, airflows around and through mined-out areas, leakages through stoppings and other control devices, and the use of multiple fans all contribute to the complexity of ventilation network analysis. Fortunately, the availability of computer programs (e. g., Didyk et al., 1978; McPherson, 1966; Wang and Saperstein, 1970) has greatly reduced the difficulty in net- work analysis. However, to obtain a suitable solution to the practical problem, a ventilation engineer has to simulate various conditions based on the proposed ventilation layouts and the capacities of available fans. It is often a trial-and-error process, although engineering knowledge and judgement are required.

Jan 1, 1982

By Changhong Huang, Y. J. Wang

This paper describes the formulation of mine ventilation network optimization as a standard nonlinear programming problem and the solution of the problem using the generalized reduced gradient (GRG) method. In general, the GRG method is regarded as one of the most effective and efficient methods for solving large-scale nonlinear programming problems. The variables considered in the network optimization include air quantity, regulator pressure loss, and fan pressure for each branch. Each of the variables is constrained by lower and upper bounds. This facilitates proper assignments of ventilation requirements and provides a great flexibility to include various situations encountered in mine ventilation. The objective of the network optimization is to minimize the overall air power consumed by or supplied to the network; whereas the constraints are, in addition to the variable bounds, the two fundamental network laws: Kirchhoffs voltage law and Kirchhoffs current law. A computer program has been developed based on the GRG method for the network optimization. An example of network with 18 branches, 8 regulators and 3 fans is included for illustration.

Jan 1, 1993