Search Documents

By D. J. McCracken

During 1995, the estimated consumption of lithium minerals in the western world was 139 kt (153,000 st).This amounted to 18 kt (20,000 st) of lithium carbonate equivalent (LCE). Overall tonnage demand for lithium minerals increased by 10.8 kt (11,900 st) during 1995from 1994. From 1992 to 1995, overall tonnage demand has increased 62%, from 85.5 to 139 kt (94,240 st). There are four major producers of lithium minerals. Gwalia Consolidated in Western Australia is the largest producer of spodumene. It supplies high-grade spodumene concentrate, fine-spodumene concentrate, glass-grade spodumene and chemical-grade spodumene.Tantalum Mining (Tanco) of Manitoba, Canada, produces high-grade spodumene concentrate, fine-spodumene, concentrate and montebrasite. Bikita Minerals in Zimbabwe is the largest manufacturer of petalite. It supplies high-grade and container-glass petalite.

Jan 1, 1996

By M. Tamlin

The state of the lithium mineral industry is closely linked to the performance of the glass and ceramic industries and to the overall economy. Demand for the glass/ceramic products in Europe, Asia and North America remained strong during 1999. This was due to a slight improvement in the economy during the latter half of the year. Consequently, demand for lithium minerals was firm, with a positive outlook. The major economic minerals for lithium are spodumene, petalite and lepidolite. The latter was once the primary mineral. But its importance hasdeclined since the 1960s. The lithium industry consists of two different segments: •The lithium minerals segment mines from hard-rock deposits and physically processes the material to high-grade concentrates. •The lithium chemicals and metal industry segment. The major feedstock for specialty lithium chemicals was previously high-grade spodumene ore converted to lithium carbonate. However, most lithium carbonate is now sourced from salars in North and South America.

Jan 1, 2000

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

In early 1970, General Mills Chemicals, Inc. announced the availability of en improved liquid ion exchange reagent, LIX® 64N, for the recovery of copper from various solutions, such as dump leach liquors. LIX 64N has been shown to be a considerable advance over LIX 64, and is presently in use in three commercial plants. Results have been very gratifying. For example, one of the plants was designed for operational production of 40,000 pounds copper per day, and in fact reached this output within the third week following startup of the plant. In addition to the operating plants, another is scheduled to come on stream this month with L D( 64N being used to extract and recover both copper and nickel. The chemical properties and operating characteristics of this reagent have been fully described in a previous paper. 1 LIX 64N is quite an effective and selective extractint for copper, even with copper contents as high as 15 g/l, but the reagent is somewhat limited in pH range, and loses some of its extraction efficiency as the pH drops below 0.8. Liquors derived from vat leaching, electrolytic tankhouae bleed streams, or some of the new leach schemes derived to solubilize copper from sulfide concentrates are examples of the liquors that present major problems when treated via liquid ion exchange. LIX 64N could extract some of the copper from such streams, but recovery was limited to about 75 percent. Also, in some parts of the world there are streams which are relatively low in copper (-5 g/l) but which are very high in acid (25-50 g/1 H2SO4). Again, LIX 64N can attain only about 75 percent recovery from such streams. For effective treatment, these streams require a reagent which will maintain the excellent selectivity of LIX 64N, and will

Jan 1, 1971

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By T. Naarttijärvi

The Fabian ore body near Malmberget, Sweden, has an ore reserve of 5 Mt of predominately low grade iron ore, containing 40-55% Fe. Mining began in 1971 with a new method called slot block caving. About 2 Mt were mined, but poor fragmentation resulted in too much secondary blasting. This decreased mucking efficiency to such an extent that the method was abandoned after only 40% of the ore volume had been mined. At this stage a large stope (180 x 30 x 100 m) had been excavated. Although the exposed area was quite large, no caving action occurred in the hanging wall or in the ceiling. LKAB decided in 1977 to introduce sublevel stoping using 105-mm-diam holes. This was the first time large diameter holes were used underground in Sweden. The method had been evaluated in collaboration with the University of Luleå (LuH), the Swedish Detonic Research Foundation (SveDeFo), and the Swedish Mining Research Foundation.

Jan 3, 1982

Continuous improvement has become the watchword of the 1990s for most iron-ore-processing operations. In many instances, this improvement has been achieved through stepwise application of advanced control techniques to optimize operations. The benefits of this stepwise application have been great. However, they have fallen short of the full potential offered by the prospect of overall plant optimization. The successful integration of computers, instrumentation and control software throughout a plant promises to deliver an additional 3% to 5% of productivity in even the best-run plants (Herbst and Bascur, 1984). LKAB is Europe's largest iron-ore producer and a leading implementer of advanced control technology. In the late 1980s, LKAB introduced advanced control in its concentrator at Kiruna, Sweden to improve plant performance through higher productivity, greater efficiency and lower costs at each processing step.

Jan 1, 1995

By Peter J. Szabo

Many mining engineers tend to think of the economic analysis of mining ventures and projects on an f.o.b. mine basis. This is especially true of mines that are operated in an established domestic mining district. Here, transportation costs are many times smaller in comparison to overall delivered prices. One has only to consider the development economics of taconite mines in Minnesota with production destined for lower lake ports to see the truism of this statement. In the international arena, however, with consumers such as Japan and Europe located thousands of miles from source countries such as Brazil and Australia, the situation is different because mineral transportation is often a critical factor in determining project viability. This article is being presented to provide a basic understanding of the factors that govern ocean transportation of the three largest bulk mineral commodities shipped around the world: iron ore, coal, and phosphate. The major dry bulk commodity trades as a percentage of volume shipped are iron ore, 45%; grain, 25%; coal, 20%; phosphate rock, 5%; and bauxite and aluminum, 5%. Most of these commodities are carried by bulk carriers rather than tankers. These are vessels that have cargo, usually in solid form, loaded directly into the hold of a vessel by shore-side materials handling facilities or, in the case of a geared bulk carrier by the vessel's cranes and derricks. Gearless bulk carriers are used in most cases for iron ore and coal. Geared bulk vessels are mainly used for minor dry bulk trades such as ore concentrates (copper, lead, zinc, etc.), fertilizers (phosphate, potash, etc.), cement, petroleum, and coke. There has been, however, a trend toward using more self-unloading ships in both iron ore and coal ocean transport. And large vessels, such as the Universe Kure of Japan, have been designed with a cargo capability of 157 kt (155,000 dwt (deadweight tons)). Trade patterns of major bulk commodities are influenced by the Panama and Suez canals. Both of these canals have draft limitations that prohibit large, deep-draft, ocean-going vessels from using them for shorter trade routes used by Panamax and Suex vessels. The shipping industry has developed two widely used vessel classes; the Panamax and Suex vessels. The former is the maximum size vessel that can pass through the Panama Canal, usually 51-61 kt (50,000 - 60,000 dwt), depending on the season and draft of the vessel. The Panama Canal is usually 0.6-0.9 m (2-3 ft) deeper in the winter than in the summer. Thus, less cargo can be carried by the same size ship in the summer through the canal than in the winter. The Suex vessel is in the 71-81 kt (70,000-80,000 dwt) class. This larger vessel is able to transit the Suez since Egypt deepened the canal following the Seven Days War. Recently, the Suez Canal has been deepened to accommodate vessels with drafts as deep as 152 kt (150,000 dwt).

Jan 10, 1982

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Greg Barfoot, Alex Harrison

Conveyors with multiple drive pulleys of the same diameter and wrap, driven by identical motors through gearboxes of the same ratio, consume different powers. The fundamental issues related to this problem hinge around the drive pulley co- efficient of friction and the intermediate tension. Some basic design concepts will be presented with reference to validity and applicability. The paper will describe some experimental results obtained from multiple drive conveyors in which the drives are spatially separated. The dynamics of tripper drive and linear booster drive systems are overviewed with reference t

Jan 1, 1993

By K Timtner

As shown in former publications there are problems in load sharing of backstops in multiple drives of conveyors. Therefore, detailed calculation methods and design recommendations are required. In this paper various designs of load sharing methods are described and a dynamic torque calculation method will be presented. With this method the loadsharing properties for low and high speed backstops are calculated and compared. These properties depend on the spring characteristic of the drive train between backstop and load. Furthermore, the properties depend on the method of torquearm support and shock absorber configuration. Remarkable differences for external and internal backstops are shown

Jan 1, 1998

By Xiaoyan Luo, Congcong Dai, Gaipin Cai, Xin Liu, Lu Zong

To overcome the difficulty of accurately judging the load state of a wet ball mill during the grinding process, a method of mill load identification based on the singular value entropy of the modified ensemble empirical mode decomposition (MEEMD) and a probabilistic neural network (PNN) classifier is proposed. First, the MEEMD algorithm is used to decompose the vibration signals recorded under different load states to obtain the intrinsic mode components, and a correlation coefficient threshold is used to select the sensitive mode components that characterize the state of the original signal. Second, singular value decomposition is used to obtain the singular value entropy. Finally, the load state of the wet ball mill is judged based on the magnitude of the singular value entropy. A characteristic mill load vector is constructed from the singular value entropies of the cylinder vibration signals recorded under different load conditions and is used as the input to a PNN, which then outputs the predicted ball mill load state; in this way, a load state identification model is established. Grinding experiments are presented to verify the effectiveness of the proposed method, showing that the method can accurately identify the load state of a wet ball mill. ()