Search Documents

The paper discusses the improvements achieved after an external sparger flotation column was installed as a final cleaner at the Northam Platinum Ltd. UG 2 concentrator in South Africa. It further discusses the improvements achieved after the conversion of a conventional flotation column, utilized as cleaner in the Merensky concentrator, to an external sparger flotation column. Finally, the application of the above knowledge in the design and commissioning of an external sparger flotation column as final cleaner in the furnace slag concentrator, is also discussed. 1. FINAL CLEANER AT THE UG 2 CONCENTRATOR The MF2 designed UG 2 concentrator is processing 75 000 tonnes run of mine ore at a head grade of 4.0 g/t 3PGM+Au and a feed Cr2O3 concentration of 28 %. Since commissioning of the plant in 2001, Cr2O3 in final concentrate amounted to approximately 5 % of the total mass. Although final concentrate produced from the UG 2 concentrator is blended with final concentrate obtained from the Merensky concentrator before smelting, blended Cr2O3 values in excess of 1.6% lead to difficulties in the subsequent smelting process. Several options for reducing the amount of Cr2O3 in final concentrate have been evaluated namely:- ? Differing types of depressants at various dosing rates. This test work did not reduce the amount of Cr2O3 reporting to final concentrate by any significant extent. ? Reduction in mass pull to minimize the entrainment of Cr2O3 in the concentrate stream.. This process change had a detrimental effect on PGM recovery. Conclusions were drawn that conventional mechanically agitated flotation cells could not achieve the required selectivity without sacrificing PGM recovery. As a consequence an alternative mechanism needed to be incorporated for the final cleaning of PGM concentrate.

Jan 1, 2007

By Vinay Kumar Agrawal, Rama Nath Praharaj

IMFA Group is the largest producer of Charge chrome not only in India but also in Asia. This Group has plants situated at Therubali and at Choudwar. They also have a Thermal power plant at Choudwar which not only caters to the power requirement of Choudwar plant but also supplies power to Therubali. The plants are fed for Chromite ore through the captive mines namely Nuasahi Chromite mines (40.47 Ha) , Bangur Chromite mines(37.34Ha), Sukinda chromite mines (116.76 Ha), Mahagiri Chromite Mine(73.777 Ha) and Chingudipal Chromite mines (26.62 Ha). Nuasahi Chromite Mine, which is situated in Keonjhar district, is an underground mine and is based upon best technological advancements in the industry. The underground mining operation is certified under ISO-9002, ISO-14001and OHSAS 18001. This not only shows the concern for the quality, environment but also for the health of the employees. The Nuashahi is the first chromite mine to backfill the opencast excavations created during the last 50 years and carry out the production from underground area below the opencast workings. This paper deals with the state of art technology of sub-level open stopping in thin ore bodies. The under-ground mine openings was started in the year 1997. In next four years the production of chromite from underground was started.(2001). At present the mine is in a good shape with several running stopes. Today it is producing around 10,000 Mt per month of chromite. The development of the mine is carried out with an average of 200 mtr per month of tunneling. The mine is having a mechanical ventilator having a capacity of24000 M3 per hour at 50mm water gauge, thus feeding sufficient air for the persons working in underground. The mine is being dewatered through a most modern positive suction sump, having a capacity of 500 cum and operated with 120 HP pumps. After commissioning of this sump in the year 2003, the mine has taken a quantum jump in production with remarkable saving in power consumption.

Jan 1, 2007

By K. Nong, H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2007

By I. Beukes, H. Kotze, B. Krause, R. P. Hattingh

Hillendale Mine is operated by Exxaro KZN Sands, and is situated on the north coast of KwaZulu-Natal in South Africa near the towns of Empangeni and Richards Bay, some 200 km north of Durban. During the mining operation the heavy minerals rutile, ilmenite, zircon and leucoxene are extracted for further beneficiation at a processing complex near the town of Empangeni. The deposit contains approximately 25% slimes (defined as the sub-45 micron fraction), and is mined using hydraulic monitoring. Run of mine is gravity fed down launders to pump stations, which deliver the material to a primary wet plant. Slimes is separated from the run of mine prior to the heavy minerals being separated from the sand. Sand tails containing approximately 2-5% slimes is pumped to the mining void. The slimes is thickened to a density of approximately 1.2, and most of the resultant material is pumped to a sub-aerial deposition site (residue dam). The area is characterized by an annual rainfall of approximately 1300 mm, which is relatively high by South African standards. From an agricultural perspective the soils are deep and well weathered. Dryland agriculture has been practised on an extensive scale in the area for the past 70 years. Sugar cane in particular is cultivated on and around the mine area. In terms of environmental approvals, the post-mining land use and objectives are defined as economically viable and sustainable sugar cane cultivation in the mined areas. During mining the soil profile is destroyed. In this paper the establishment of a reconstituted soil profile is discussed, with specific reference to the methodology that is being followed to achieve the homogeneous blending of sand and slimes. Defining the rehabilitation strategy and soil specification Strategically Exxaro KZN Sands divided rehabilitation into four aspects, comprising physical rehabilitation (restoration of soil structure), vegetative rehabilitation (restoration of vegetative cover), ecological rehabilitation (restoration of sustainable ecological communities), and sustainability (sustainable man/environment interface) (Hattingh and Viljoen, 2006). It is believed that the key to successful rehabilitation lies in achieving a substrate (soil) suitable for the establishment of the target vegetation. During the development of the rehabilitation strategy the key factor in the establishment of a suitable soil profile was shown to be the soil water retention of this material. Since dryland agriculture is practised, this aspect becomes critically important in ensuring that the post-mining land use is sustainable (Hattingh et al., in prep.). From a financial perspective, a closure certificate being issued implies that the state takes over financial liability for the rehabilitated land. This has significant implications for the state-the default position will be that all possible latent and residual impacts must be identified and known prior to a closure certificate being issued. From the mine's perspective this precautionary approach by the state implies that post-operational costs cannot be quantified exactly, and our approach is therefore to mitigate the risk of a long post-closure care and maintenance phase by means of addressing all potential latent defects during the operational rehabilitation phase. The financial viability of the soil reconstitution process itself is therefore not measured against other rehabilitation methods, but against the risk of not achieving closure. During a series of technical workshops comprising experts in the various disciplines in the rehabilitation of the soil profile were identified. These aspects include the re-establishment of a functional soil profile, soil physical characteristics, soil chemistry, soil biota, salinization potential, erodibility and soil weathering. The natural soils in the Hillendale area have been classified in terms of the South African soil classification system (MacVicar and co-workers, 1991) and consist of Hutton (orthic topsoils on red apedal subsoils) and Clovelly (orthic top soils on yellow apedal subsoils) soil forms. The topsoils consistently comprise medium to fine grained sand overlying heavier textured sandy clay loam to clayey subsoils. The topsoil structure consists of a single grain structure, whereas subsoils are apedal. These soils are typically deeply weathered and do not show secondary structures. During the mining process a layer of topsoil (300 mm) is stripped off, and the balance of the material down to the footwall is processed. Sand with 2-5% slimes (defined as the sub-45 micron fraction) is returned as backfill in order to re-establish the dune to approximate the previous landform. From an agricultural perspective this material is not suitable for the dryland cultivation of sugar cane. A capping of more suitable material therefore has to be provided. The most significant difference between the premining soil form and the backfill material is the percentage slimes, consequently a mixture of the sand and slimes is required as a capping over the backfilled sand. The required thickness of the cap is a function of specifically plant growth requirements, erodibility, weathering and runoff (Hattingh, et al.; in prep.). The percentage slimes required in the cap is a function of mainly soil water requirements (Hattingh and Viljoen, 2006). The conservative indications to date show that the reconstituted soil profile should consist of a homogeneously blended mixture of 70%-80% sand and 30%-20% slimes up to a maximum of 2 metres thick. This will be sufficient to ensure growth during dry periods.

Jan 1, 2007

By P. Mokwena

Paper written on project work carried out in partial fulfilment of BSc (Hons) in Chemical Engineering Diamond synthesis has attracted a great deal of interest because of its exceptional properties and various applications. In this study, the chemical catalytic vapour deposition (CCVD) method was used to synthesize diamond films using acetylene as carbon source and hydrogen as carrier gas at a temperature of 1000°C, and their thermodynamic stability was studied. Photographic analysis revealed that these products are diamond films, Ramman spectroscopy confirmed that they are graphitic while confocal laser scanning microscopic image analyses proved that these diamonds films have structural defects due to iron impurity from the catalyst precursor. The quantity of diamonds films produced is also proportional to the acetylene to hydrogen ratio but these films are larger in size at lower acetylene to hydrogen ratio. Thermogravimetric analyses showed that transformation of these materials begins at 25°C but could not be used to determine if a temperature range below 25°C exists. The stability of these CCVD-synthesized diamonds also increases below 25°C when stored at different temperatures.

Jan 1, 2007

By A. Cáceres, L. Navarro, N. Altmann, R. Betinol

Copper concentrate is produced in Chile in the high Andes and transported to the coast for shipping through long distance pipelines. The pipeline and fittings installed have to withstand the high abrasion and corrosion environment of the copper concentrate. To protect the inside tube wall against corrosion, high density polyethylene (HDPE) liner is used. While HDPE liners can protect the steel wall against corrosion, it has also been assumed that the low surface roughness of the HDPE liner also inhibited incrustation caused by calcium carbonate and sulphate deposition. Recent events have indicated otherwise in a couple of concentrate pipelines for which BRASS has provided consultant service. This paper delivers a case study which includes (i) formation of incrustation and adhesion to HDPE liner, (ii) the detection of the incrustation through hydraulic analysis, (iii) the mechanism of removal of incrustation, and (iv) the catastrophic effects of their presence in an emergency situation.

Jan 1, 2007

By P. Stevenson

Correlations for the critical velocity needed to hydraulically convey particles in horizontal, or near-horizontal, pipes are either explicitly dependent upon the shear stress imparted by the fluid upon the surface of the particle bed, or require a velocity and hydraulic diameter. Often such approaches are modified to account for pipe inclination by the introduction of simple factors. However, we assert that the physics that underpins the hydraulic conveying of particles in steep pipes (such as a directionally drilled oil well) is dissimilar to that which governs particle behaviour in horizontal pipes. In steeply inclined systems, a sliding sediment induces an upward counter flow and hence an autogenous contribution to the shear rate. The physics underpinning particle hydraulic conveying in steep systems is explored using the separation results of Laskovski et al.10

Jan 1, 2007

By D. Burrows

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By A. J. Van Der Merwe, N. A. Barcza, M. Boyes, N. R. Clarke

Oriel Resources has with the support of SRK (Cardiff) and DRA and Mintek (South Africa) carried our a Definitive Feasibility Study (DFS) to recover high grade chrome ore from its Voskhod deposit very close to Chromtau that is near to Aktobe in Kazakhstan. Voskhod is a large podiform ore body that contains nearly 20million tons of chromite grading about 48% Cr2O3 and with a Cr/Fe ratio of over 3/1. Selected bore hole core samples were obtained from the confirmation drilling programme during the DFS phase of the project in 2005 for pilot plant test work to design the mineral beneficiation plant. The chrome ore is characterised by four main types, namely high grade lumpy and chip sized ore, high-grade fine ore, lower grade (subordinate) lumpy ore and lower grade fine ore. Gravity separation tests carried out by Mintek showed that the large density difference between the high grade (at over 3.7t/m3) and lower grade ore (at less than 2.97t/m3 ) should ensure very good separation in the DMS drum and DMS cyclone stages resulting in high recoveries of Cr2O3 - rich chromite ore products. Very high chrome ore grades of up to 64% Cr2O3 and Cr/Fe ratios of 4 to 1 were obtained at an 80% mass yield from selected samples of lumpy and chip ore size fractions. The overall predicted recovery from the design work on the mine and plant is expected to be closer to about 70% of the ROM (Run of Mine) feed. DRA has completed the design of the mineral processing plant to recover about 900 kt/a of chrome ore from the 1.3 Mt/a of ROM feed. The plant has been sized to handle up to 1.5 Mt/a and will also be able to address the variability in ore feed as different regions in the deposit are mined. The lumpy high-grade product and the chips size fraction is expected to grade around 48% Cr2O3 and the fine concentrate between 56 and 58%Cr2O3 The ratio of products is expected to be about 70, 15 and 15 percent respectively but will vary to some extent during the expected 20 year life of the mining operation based on including the associated adjacent Karaagash deposit together with the Voskhod deposit. The prediction of the product split from the processing plant depends on many factors such as the geology, mineralogy, mining, handling and metallurgical processing. An overall process flow model has been developed that covers the ROM ore, the various types of chrome ore feed to the mineral beneficiation plant, the projected products and the subsequent smelting of the chromite ores to produce High Carbon Ferrochromium. The model allows the optimisation of the quality of the chrome ore in terms of Cr2O3 content, Cr/Fe ratio and recovery to be studied. This information can also be evaluated in terms of the economic requirements for smelting High Carbon Ferrochromium (HCFeCr) at a given location. Oriel is planning to supply chrome ore to Ferrochrome plants mostly in China and Russia. The use of the model will assist to maximise the value of the Voskhod project to its owners and also assist the users of the chrome ore in selecting the appropriate supply quality to meet their needs for a given smelter operation. The smelting of high grade Voskhod ore requires a limited addition of about 5 to 7% quartz to flux the MgO and Al2O3 and about 25% coke as a reducing agent to produce an alloy containing from about 65 to 74%chromium depending on the Cr/Fe ratio.

Jan 1, 2007

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

The corrosion behaviour of a low carbon steel was investigated in synthetic seawaters with and without Sr2+. It was found that strontium substitutes for calcium in aragonite, rather than precipitating as discrete strontianite (SrCO3). The aragonite deposits that formed in the presence of Sr2+ were finer than those that formed in the absence of Sr2+. It is believed that an increase in the strontium content of aragonite induces a decrease in its solubility, which in turn results in a higher nucleation rate of the precipitates. Furthermore, the growth rate of aragonite is decreased by the presence of Sr2+in the solution. It is concluded that Sr2+is an essential ingredient in any artificial seawater when calcareous deposits are investigated on steel. Keywords: corrosion, seawater, calcareous deposits, strontium, aragonite.

Jan 1, 2007

By D. F. Sinclair

It is often said in business that if you don't have a customer you don't have a business. The same rule applies to project evaluation; if you don't have customers you really don't have a viable project. It is therefore essential that in the early stages of project evaluation the following fundamental questions are addressed: ? What products will this project produce? ? Who are the potential customers? ? What are the customers' requirements with respect to grade and impurities? ? Do they have adequate capacity to take the production from the proposed project? ? Will the products introduce adverse effects in the customer's process circuits? ? Will additional waste streams requiring disposal be produced? In the past the attitude has been along the lines of the customer will take whatever we produce at the mine site. Times have now changed with customers now operating under much tighter environmental regulation with waste disposal becoming increasingly difficult. It would therefore be prudent that the principles of product stewardship be used as a tool in project evaluation. This paper will provide a general discussion on customer requirements and provide detail on case studies of the impact of mine products on smelter process circuits. It will provide examples where there were synergies between the mine product and the smelter circuit and where the mine product had adverse impacts on smelter performance.

Jan 1, 2007

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007

By E. J. McLean

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By Godofredo F. Barrios

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings from as fine as 100 microns and coarser have been used. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies which allow an end user to consider urethane screen surfaces for fine screening applications. These technologies allow an end user to use the inherent advantages of urethane with regards to wear resistance while also realizing the benefits that a high oper area urethane screen surface can bring. These benefits include non blinding characteristics and feed capacities that which rival that of traditional stainless steel surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines they are used in conjunction with. There will also be a presentation of case studies of commercial installations where these technologies are utilized. These case studies are from the base metals industry therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints which must be taken into account when considering urethane screen surfaces such as temperature and chemical attacks. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By A. K. Das, S. Pathak, C. Bhanu, P. K. Tripathy

Ferroalloys are integral part of steel melting process. The purpose of using ferroalloys is three fold e.g. killing of steel, modifying the slag composition and steel alloying. Amount of ferroalloys used for alloying is subject to requirements of steel properties e.g. yield strength, ductility, formability etc. Variety of ferroalloys (some-times pure metal) is used by steel industries depending upon their techno-economic feasibility. Size, chemistry and modes of addition of ferroalloys are suitably engineered to bring in operational consistency and cost benefits. Of late, Tata Steel has tried out a few ferroalloys for the first time with interesting results to meet the specific requirements of high strength interstitial free (IF) and micro-alloyed steels. Some of these ferroalloys have been put into regular use with complete or partial replacement of ferroalloys used earlier. Size of one of the ferroalloys has also been modified without any other adverse effects. This paper summarizes requirements of ferroalloys for the steel industry with special emphasis on recent trials.

Jan 1, 2007