Search Documents

This paper describes DRA?s involvement with the expansions at Tati Nickel, Phoenix Mine, that have taken an initial plant design of 3.6 Mtpa (originally built by Murray & Roberts), up to 5 Mtpa, and eventually 12 Mtpa capacity. Initially, the plant could not achieve the design name plate capacity for the first few years of operation, as a consequence of the notoriously hard and abrasive nickel ore affecting primarily the operation of the crusher circuit. In order to extend the life of mine, Tati? assessed and then redefined the mining plan, choosing to increase the Phoenix mine reserves to a lower cut-off grade. In order to increase nickel units produced, the concentrator had to therefore treat additional tonnage at lower head grades. Site investigations and field tests around the comminution circuits are outlined, indicated that the milling circuit could be increased to 650 tph, from the initial design of 470 tph, for a similar feed grade and recovery. A project was initiated to debottleneck the crusher circuit and achieve the new target throughput. (Project 5M). This was followed by a feasibility study of the impact of pre-concentration by DMS, which after promising laboratory tests, was followed up with the installation of a 200 tph ?demonstration? plant. The success of this demonstration plant provided the impetus to expand the supply to the 5 Mtpa mill from a large preconcentration stage. A gyratory crusher (one of the largest and most powerful) will receive ore directly from the open pit operation, feeding into a secondary-tertiary crushing plant followed by a modular DMS preparation circuit. Four large DMS processing modules have been installed to treat the tonnage, with high expected rejection levels. Finally a review of the DMS process capability on an ostensibly disseminated micro-gabbro nickel ore is given, which shows the remarkable impact that preconcentration can have on an operation, both in terms of profitability and a successful process ?expansion?. The performance of the DMS plant has significantly extended the life of mine, allowing the mine to significantly reduce mine cut-off grades and curb its previously selective mining practice.

Jan 1, 2009

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009

By G. L. Smith

This paper consolidates the key elements of seven contributions, on strategic long-term planning, to two of the three international conferences on Strategic versus Tactical approaches in Mining held over the period 2005?2008. The holistic concept of strategic long-term planning as developed and implemented at Anglo Platinum is described. Consideration is given to the planning cycle, principles supporting the construction of the long-term plan, and aspects of unique best practice as developed in Anglo Platinum. Further description of Anglo Platinum?s approach to corporate governance, including the processes, methodology, systems, unique tools and techniques that are applied to value and select capital investment options is also given.

Jan 1, 2009

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

This paper examines manning best practice in the Australian mining industry, comparing the mining of gold with mining of other commodities. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 7 open pit and 14 underground studies of gold mines in Australia from a database of over 50 studies. The data were collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2009. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. The proportion of supervisory to operations personnel and labour costs as a percentage of total operating costs is highlighted. Minimum manning requirements for the range of mining methods are indicated, irrespective of the size of the operation. The benchmarking results provide guidance by indicating a range of manning numbers and trends which are likely to be appropriate for the scale and type for a range of mining operations. When combined with benchmarked productivity and cost data, manning results help identify potential areas for business improvement, driving gains in the efficiency of labour. Finally, the paper considers perspectives on best practice for manning and the limitations in application of this type of analysis in a global context.

Jan 1, 2009

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By S. G. Ercelebi

In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli Open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system. Keywords: Open pit mine, equipment selection, dispatching, linear programming, closed queuing network theory

Jan 1, 2009

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

By A. V. Wilke

The metallurgical balance is a tool usually applied in the mining industry. The final result is used for different objectives. All the existing software for the calculation of the metallurgical balance fits the numbers in such way that a logical correspondence between the input and output materials exist. Nevertheless, the accuracy of the metallurgical balance strongly depends on the quality of the input data. Division El Teniente of Codelco Chile has been optimizing the metallurgical balance system the last 14 years. As well, it has participated in the development of corporate norms to optimize the operations of sampling and weighting systems. As a consequence, the precision and the accuracy of the metallurgical balance have been improved in a significant way. Also the understanding of process variability was enhanced. The improvements have allowed Codelco to discover and minimize hidden losses and to better support top management decisions. The present paper describes the main aspect of the continuous improvement process.

Jan 1, 2009

By S. A. Abdel Sabour

Strategic decisions in the mining industry are made under multiple technical and market uncertainties. Therefore, to reach the best possible decision, based on information available, it is necessary to integrate uncertainty about the input variables and model financial risk of the project?s merit measures. However, this provides few useful insights to decision-makers unless accompanied by modelling management responses to uncertainty resolutions. It is widely acknowledged that conventional decision-support methods based on static, no-change, discounted cash flow (DCF) techniques such as net present value (NPV) and internal rate of return (IRR) tend to provide inaccurate value estimates. This could mislead the strategic decision-making process and result in significant value losses. This paper aims to model financial risk related to uncertainty about market variables such as metal prices and foreign exchange rates. Other sources of risk that are related, for example, to geology and production costs are not considered in this work. The article outlines a flexible financial model that integrates uncertainty about market variables and management flexibility to react to uncertainty resolutions into mine project valuation using a real-options valuation technique based on Monte Carlo simulation. Significance of information generated from this simulation-based flexible valuation model to the strategic decision-making process is tested using an illustrative case study of a Canadian mining project. The project is a typical multi-metal, open pit mine that produces copper and gold. In this case, there are three uncertain market variables, which are: copper and gold prices and US$/CAN$ exchange rate. Financial valuations are carried out using both the conventional static DCF method and a flexible real-options model. In the flexible model, management flexibility to decide whether to go ahead with the next expansion or terminate production operations is integrated. Results show how the flexible financial model can enhance the decision-making process.

Jan 1, 2009

By C. M. Rule

Energy efficiency is currently a significant area of interest due to the Eskom power situation, which led to severe power impacts to the PGM, and indeed whole SA primary industries, in early 2008. Anglo Platinum has focused on energy efficiency for a number of years, especially in the concentrator operational area. New comminution technologies have been aggressively developed, which have shown real metallurgical efficiency gains as well as significant energy efficiency and saving potential for Anglo Platinum?s total electrical consumption as the company expands into a growing PGM demand market. This paper illustrates this programme?s activities, potential and considerable achievements to date.

Jan 1, 2009

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009