Search Documents

By V. A. Marple, K. L. Rubow

"IntroductionA particle dispersion system has been developed to aerosolize bulk powders or material deposited on surfaces such as filters. The size distribution of the aerosolized particles can then be obtained by sampling the particles with an aerosol sizing instrument such as a TSI aerodynamic particle sizer (APS) or a cascade impactor.Of particular interest is the applicability of using this technique to obtain the size distribution of particles collected on filters. This system has been used to determine the size distribution of coal dust particle collected on membrane filters. The use of this device in this application is quite intriguing in that, if this technique can be shown to accurately determine the size distribution of airborne particles, one can easily collect particle samples using either personal or area particle samplers, determine the mass concentration of the collected material through gravimetric techniques and then use the particle dispersion system coupled with the APS to determine the particle size distribution. With this technique one can determine the particle size of dust in environments, such as underground mines, where it would be inconvenient or impossible to use a particle sizing instrument.Particle Dispersion SystemA prototype particle dispersion system has been developed for aerosolizing particles. A schematic diagram of the system is shown in Figure 1. The system consists of mechanism for advancing the particle sample beneath a dust pickup tube, a venturi for deagglomerating the particles, and a instrument for analyzing the aerosolized particulate matter.The procedure to analyze a particle sample is as follows. The particles to be aerosolized are placed on a sample plate from where the particles are picked up by an air stream flowing upward in a small capillary tube (dust pickup tube). This tube operates as a small vacuum cleaner passing over the sample plate. The air is drawn up the capillary tube at a rate of 2 L/m by a venturi aspirator. This is accomplished by placing the outlet of the capillary tube near the throat of the venturi. The accelerated velocity of the air creates a low pressure in this region which draws flow up the capillary tube. From the outlet of the capillary tube particles are transported to the inlet of the APS where a small fraction are sampled and the aerodynamic diameter of the particles determined. The particles which are not measured by the APS are passed into a HEPA filter."

Mar 1, 1989

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By R. V. Ramani, R. L. Frantz

"The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRls) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRis at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental understanding of all aspects of respirable ~~9t associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area. IntroductionExposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration.The stated objective of the Federal Mine Safety and Health laws is to"" permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease ."" Significant progress has been made in lowering the dust levels in mines since the inception of the Bureau's respirable dust research program. It is generally agreed that mines are less dusty today than they were a decade ago. However, the most serious hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found."

Mar 1, 1989

By A. Wahab Khair, N. P. Reddy

"Abstract. This paper attempts to characterize coal breakage due to the action of a continuous miner. Coal blocks with an approximate dimension of 45.7 cm x 38.1 cm x 15.2 cm (18 in. x 15 in. x 6 in.) were first subjected to confining pressures equivalent to in-situ conditions. Then the blocks were cut along the face/butt cleat direction by the cutting head of a specially designed unique automated rotary coal cutting simulator (ARCCS), simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-sit and operating parameters a number of other para¬meters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis.INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969 was enacted to emphasize to coal operators that the airborne respirable dust should not exceed 2 mg/m3, thus reducing the incidence of coal workers pneumoconiosis.Dust control techniques such as conventional water sprays and dust collectors are only partially effective and require additional equipment expenditures. A more authentic approach would be to reduce respirable dust at the source the continuous mining machine cutting head, where the fragmentation process occurs. Improving the fragmentation process by characterizing the coal breakage will not only reduce respirable dust at the face, but it will also decrease the amount of respirable dust that is liberated during the secondary handling.Fragmentation of coal can be expressed as a function of three major groups of parameters; namely, 1) coal properties, 2) in-situ conditions and 3) operating parameters. This paper deals with the characterization of coal breakage along both face/butt cleat direction as a function of machine operating parameters such as rate of advance, angle of attack, bit configuration, bit lacing (spacing and pattern) and bit speed at various equivalent in-situ pressures."

Mar 1, 1989

By J. M. Mutmansky, C. Lee

"IntroductionRecognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries, Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs.To identify the causes of CWP, many research efforts have been made throughout the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous research studies has appeared elsewhere (Mutmansky and Lee, 1984).The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented"

Mar 1, 1989

By R. Hogg, T. F. Dumm

"It is generally agreed that dust characteristics play a role in the development of Coal Workers' Pneumoconiosis (CWP). Unfortunately, there is a serious lack of information on what the characteristics of mine dust actually are and how they vary among different mining regions, coal seams, etc. This paucity of data can generally be attributed to the serious problems encountered in collecting sufficiently large quantities of dust for conventional analytical procedures.Personal samplers are widely used in coal mines for regulatory and enforcement purposes. Generally, these provide information only on the total (respirable) dust loading in the mine atmosphere and on the mineral matter (primarily quartz) content of the respirable dust. A procedure has been developed by which samples collected with a slightly modified personal sampler can be analyzed for particle size distribution, total mineral matter content and elemental composition, in addition to the standard mass and quartz measurements. These analyses could readily be performed on a routine basis. Shape analysis by Scanning Electron Microscope (SEM) could easily be included if appropriate shape criteria are established. Extension of the procedure to include the determination of complete size/specific gravity (composition) distributions is quite straightforward provided sufficiently large samples (at least 10 mg) can be collected. Typical sample sizes for a personal sampler carried by a miner for one shift range from about 0.5 to 2 mg.The basic procedure was developed and evaluated using synthetic mine dust prepared in the laboratory. Field tests in three working mines in Pennsylvania and West Virginia have confirmed the applicability of the approach to the real world. Particle size distribution measurements on mine dust collected in the modified personal sampler were found to agree closely with the results of simultaneous in situ measurements obtained using cascade impactors."

Mar 1, 1989

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By H. S. Chiang, Y. Luo, S. S. Peng

"IntroductionThe way in which the particle sizes distribute in the airborne coal dust plays an important role in the transportation of the dust in the mine air and human respiratory systems. Though the particles of a size less than 10 microns could be inhaled, the real distractive portion of the dust is that the sizes range from 1 to 5 microns since only they can reach the lungs and be retained there. Those with an equivalent diameter larger than 5 microns will settle on the membranes of the branchial tubes(1) while those with diameter less than 1 micron can either be exhaled out of the lungs or the settled quantity is so insignificant that does very little harm to the lungs. In the transportation process, the finer dust will fly farther away from the sources than the coarser ones. Thus once the fine dust is generated and becomes airborne, it will spread out to a larger area.In this paper, the coal samples collected from two longwall faces were analyzed statistically for size distribu¬tion. A mathematical model is proposed and the effects of different conditions on the dust size distribution were analyzed using the mathematical model.Sampling and Statistical AnalysesSampling Instrument and ProcedureThe instrument used in the sampling were Mine Safety Appliance (MSA) personal sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters and constant-flow pumps.Two longwall operating faces were selected for the dust sampling. The two faces were located in two coal mines ex-tracting Pittsburgh seam. The double-ended ranging-drum shearer applying the unidirectional cutting sequence was employed. The two-leg shield supports were used for face support. The width of the two faces was about 215 meters.In each of the two faces, four sampling stations were set up. The stations were located at the cross-cut immediately outby the headentry side, the 15th support (25 m), 65th support (107 m) and 111th support (182 m) from headentry T-junction, and numbered as #1, #2, #3, and #4 station, respectively (Figure 1). At each sampling station, a group of three sampling units was hung at proper position. At cross¬cut (#1) station, the units were hung about one foot under the roofline in the center of the cut (Figure 2a), and at the stations in the face, the units were position near the hydraulic legs and one foot below the support canopy (Figure 2b).One complete set of 12 samples was collected for each day. The sampling were performed for five consecutive days. All the samplings were conducted in the morning shifts. The time duration of the sampling for each day was about five hours. During that time, the shearer might complete 5 to 7 mining cycles."

Mar 1, 1989

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

By R. V. Ramani, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways (National Academy ofSciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Mar 1, 1989

By W. E. Wallace, V. Castranova, F. Saus, D. Bates, C. A. Hill, V. Vallyathan, M. J. Keane

"Two in vitro systems are being developed to model initial stages in the interaction of respired dusts with the acinar region of the lung. Incubation of quartz and kaolin with dipalmitoyl glycerophosphorylcholine, a major component of pulmonary surfactant, suppresses the prompt C)1otoxicity of both dusts as measured by in vitro enzyme release from pulmonary macrophages or assay by erythrocyte hemolysis. Additional data is presented to quantitate the detoxification of quartz and kaolin by dipalmitoyl lecithin. Subsequent incubation of lecithin treated dusts with phospholipase enzymes results in partial to complete restoration of the assayed cytotoxic potentials, dependent on the lipase activity applied, the incubation time, and the mineral. Restored cytotoxic potential is due to removal of the prophylactic lecithin surface coating and/or due to residual lysolecithin which is produced by the partial enzymatic digestion of lecithin. Data is presented on the contribution of each mechanism to the restored toxicity. Again, this is dependent on the mineral used, the lipase activity applied, and digestion time. Additionally, a system is under development to challenge pulmonary macrophages in culture with native and surfactant treated dusts. A preliminary test of the dipalmitoyl lecithin - quartz rabbit pulmonary macrophage system is presented to illustrate the method.IntroductionRespirable quartz dust exposure is known to cause librotic lung disease; respirable clay dust exposure is less likely to do so as indicated by epidemiologic data on occupational exposures and by animal model studiesP·7) The hypothesis that damage to pulmonary macrophages in the acinar region of the lung by respired dusts is an early event in the disease process requires consideration because kaolin clay and quartz dusts are comparably cytotoxic to pulmonary macrophages in vitro.(3•9)"

Mar 1, 1989

By R. Clark Lantz, Charles Stanley, David E. Hinton

Morphometric examination of lung alterations following exposure to toxic and pathogenic substances is invaluable in detecting subtle changes which might otherwise be overlooked. Results, from evaluation of initial structural alterations, support and guide subsequent nonmorphological techniques and, when coupled appropriately, can lead to a better understanding of the pathogenesis of a disease. Morphometry is a technique which can be used to determine, quantitatively, the site, extent, development, and progression of a disease state. Determination of the extent of tissue and cellular involvement in the response to inhalation of silica has been performed in order to gain a better understanding of the development of fibrosis following inhalation of this toxicant. In addition, since silica has been postulated as one of the important pathogenic minerals in coal mine dust' it is important to understand the lung tissue response to silica prior to evaluating the effects of inhaled coal mine dusts. Male Syrian golden hamsters were placed in Hazelton 1000 inhalation chambers and were exposed to either filtered air (controls, n = 24) or filtered air plus 30 mg!m3 silica (Min-U-Si110,95%ofparticles < 5 um,n =24)for16hours per day, five days per week, for two weeks. Animals were returned to the animal quarters prior to subsequent tissue processing at 1, 4, and 12 weeks following exposure. This schedule was designed to allow time for the development of fibrosis. Lungs were fixed by intratracheal perfusion of ½ strength Karnovsky's fixative at a pressure of 20 cm H20 and tissues were taken for embedment and analysis at the light level. Determination of site, extent, and development of alterations was performed using a multitiered approach. Changes in large structures (airways, blood vessels) was determined prior to evaluation of changes at the septal tissue level. Data will be presented outlining the progression of changes. Results indicate the usefulness of morphometric analysis of lungs following inhalation of toxic substances in quantitatively defining the structural alterations.

Mar 1, 1989

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

By R. Karl Zipf, Z. T. Bieniawski

"Abstract. Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation.In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions.An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further understanding of the mechanics of fine fragment formation in coal."

Mar 1, 1989

By R. Karl Zipf, Z. T. Bieniawski

"Researchers at The Pennsylvania State University are engaged in a project to understand the mechanics of respirable size fragment formation in coal. The project is based on the premise that a thorough understanding of the fundamental mechanics of fine fragment formation may lead to techniques for reduction and better control of coal dust problems in mines. Presently, it is believed that the mode of fracture propagation which can range from pure tensile to pure shear or any mixed mode in between and the loading or displacement rate can influence the amount of respirable size fragments that are generated on new fracture surfaces during the fracture propagation process The essence of any coal cutting process is one of mixed mode fracture propagation. To study the crack propagation process, a unique mixed mode testing rig was designed and fabricated. This rig is capable of applying loads to a prenotched test specimen that range from pure Mode I (tensile mode) to nearly pure Mode II (shear mode) or many mixed mode loading combinations. It is also possible to apply different loading or displacement rates to the test specimen. With this rig, it is possible to create new fracture surfaces via the different fracture modes and under various loading conditions.These new fracture surfaces are examined with a scanning electron microscope (SEM) to characterize the amount of structural damage and respirable size fragment formation that occurs during the fracture process. Initial observations suggest that the amount of fine fragment formation and the new fracture surface appearance is related to the fracture initiation conditions, particularly the fracture mode and the loading rate. Mode II loading and higher loading rates seem to generate more structural damage and respirable size fragment formation that Mode 1 loading at slower rates.With the mixed mode test rig, the mechanics of fracture initiation for a single crack can be controlled to better understand its influence on respirable size fragment formation. Such understanding may lead to methods which characterize the tendency of specific coal seams to produce undesirable fine fragments during the fracture process, or it may lead to rational recommendations and design guidelines or coal mining machines which inherently produce less dust.IntroductionAs part of a larger effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners, researchers at The Pennsylvania State University are engaged in a project to understand the fundamental mechanics of fine fragment formation in coal. This project is part of a com¬prehensive research effort within the Generic Mineral Technology Center for Respirable Dust which is jointly administered by The Pennsylvania State University and West Virginia University.The principal source of the coal dust in underground mining is the cutting operation. The U.S. Bureau of Mines (USBM) and various European research organizations have conducted investigations into the mechanics of coal cutting for many years. These studies of airborne respirable dust (ARD) formation have concentrated on empirical studies of the various cutting parameters and their effect on ARD for¬mation. The parameters study include depth of cut, cutting speed and bit spacing.(1,2) Other studies investigated the effect of symmetric and asymmetric bit wear and various bit geometries and designs (3-5) Roepke(6) summarized the principals of proper coal cutting to minimize dust formation by recommending to ""cut at maximum depth (maximum advance rate) at all times, at minimum RPM, with the fewest possible bits, having the lowest possible included tip angle."" Most coal in the U.S. is mined with the continuous mining machine which inherently cannot meet these design recommendations.(3)It is recognized that respirable size dust particles are formed and/or liberated by a fracture process. One extremely interesting and useful study performed very early in the USBM dust re"

Mar 1, 1989

By N. S. Dalal, B. Jafari, F. Y. H. Green, V. Vallyathan

"Using electron spin resonance (ESR) spectroscopy we have carried out a systematic study of the measurement of concentrations of organic free radicals in freeze-dried lung tissue. Sixty-six tissue samples were obtained from the National Coal Workers' Autopsy Study (NCWAS). The samples were characterized in terms of the concentration per gram of the free radicals, and examined in relationship to the histopathological parameters such as age, numbers of years in the mining atmosphere, the degree of disease, and smoking history. Preliminary results indicate a positive correlation between the free radicals in the lung tissue and the severity of pneumoconiosis.IntroductionThis paper summarizes our electron spin resonance (ESR) measurements of the concentration of organic free radicals in the freeze-dried lung tissue of autopsied coal miners. This work was undertaken because it is well known that most coals contain carbon-centered organic free radi¬cals,(1,2) and recent studies from our laboratories indicated that reactive free radicals might play a role in the biochemi¬cal mechanism of coal workers' pneumoconiosis (CWP) (3) Thus we obtained 144 lung-tissue samples from the Nation¬al Institute for Occupational Safety and Health (NIOSH) in Morgantown. The samples came from the data bank of the National Coal Workers' Autopsy Study (NCWAS). This selection was unique because fairly detailed histopathologi¬cal information was available for each sample.Other recent studies in this field are those of Ohta et al (4) who conducted ESR measurements on black dust deposited in autopsied human lungs, but no coal miner was included therein. Earlier Retcofsky (2) had examined one lung-tissue sample via ESR spectroscopy and had concluded that the free radicals in the lung tissue reflected simply the fusain (narrow component) ESR signals. The present study was thus undertaken to complement the earlier work (2-4) and the results indicate a positive correlation with the disease severity fairly strongly."

Mar 1, 1989

By R. V. Ramani, R. Bhaskar

"IntroductionThe behavior of dust clouds in mine atmospheres has been a subject of longstanding interest due to both health and safety reasons. Pioneering studies in Germany and SMRE focussed on ambient dust concentration, principally aimed at determining optimum velocities for effective dilution. A summary of studies related to this area is provided by Hall,(l) Efforts to understand dust deposition from the explosion hazard point of view led to experiments in return airways (2-4) followed by experiments in longwalls.(5) Concerted efforts, either experimental or theoretical, were not made until recently to relate ambient concentration with dust deposition in mines. In 1974 Hwang et a1 (6) developed a computer model to predict dust concentration which considered deposition-concentration relationships. Also, experimental studies involving concurrent dust deposition and ambient concentration were conducted in the U.S. by Courtney et al (7 ) in operating mines. Efforts to relate theory with experimental results have been made by Owen (8) and Hwang et al (6 ) for dust deposition. There has been limited work, however, to determine the application of the theories and assumptions from aerosol sciences for modeling dust flows in mine atmospheres. (9 ) This is the objective of the work currently underway in the Generic Technology Center on Respirable Dust since· 1983 under a project titled, ""Prediction of Ambient Dust Concentration in Mine Atmospheres."" The scope of the project activities include:1. Development of a mathematical model to predict dust deposition and concentration in mine atmospheres.2. Experimental studies on dust transport and deposition in mine airways.3. Comparison of the model results with the experimental data."

Mar 1, 1989

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989