Search Documents

By D. E. Kirby

In line with the Bureau of Mines' goal of providing technology to maintain a supply of minerals adequate to meet national economic and strategic needs, a method for recovering chromite from lateritic materials was investigated. Laterites are a large resource of Ni, Co, and Cr, critical metals of which the United States has insufficient domestic sources. A roast-leach method was developed by the Bureau to extract nickel and cobalt from domestic laterites. A concurrent effort was made to recover chromium from either unprocessed laterites or the leach residues. This report characterizes laterites and laterite leach residues. It describes a chromite recovery procedure using conventional industrial beneficiation equipment for sizing, low-intensity magnetic separation, and gravity concentration. Concentrates containing 20.0 to 22.4 pct Cr (29.0 to 32.7 pct Cr203) and with a 1.6:1 to 1.9:1 Cr-Fe ratio were recovered from laterites and residues containing 1.3 to 2.5 pct Cr with recoveries exceeding 50 pct. Because of their low grade and fine size, these concentrates would be suitable for preparing chromium chemicals. The direct beneficiation of laterites for chromite recovery resulted in the minerals containing nickel and cobalt concentrating in slime products. No iron oxide coproducts of acceptable grade were recovered from either laterites or residues.

Jan 1, 1982

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By Keith L. Harris

Surprisingly, real gross national product (GNP) surged at a seasonally adjusted annual rate of 4.3% for the first quarter of 1987 according to preliminary estimates made by the Department of Commerce, the highest rate in 3 yr and significantly above the revised fourth quarter 1986 rate of 1.1% (table 1). The spurt, however, was caused by an unusual $59.5 billion rise in inventories, mostly cars and trucks, and there was little support from other sectors of the economy. Motor vehicle inventories rose as consumers continued to tighten their purse strings--consumer spending declined 0.4% for the second quarter in a row. Nonresidential and residential fixed investment and government purchases of goods and services were also down from the previous quarter. The increasing cost of energy was the major factor in the jump to 3.696 in the rate of inflation, as measured by the fixed-weighted price index for GNP, and rising inflation also helped put a damper on consumer spending. The underlying good news was that the trade deficit shrank for the second quarter in a row as imports declined at an annual rate of 11.1%. Also, profits in the manufacturing sector rose strongly in the fourth quarter, and for the first time in 9 quarters, the primary metal industries became profitable (table 1). If one discounts the anomalous inventory growth, the bottom line is that the economy continues to grow at close to the expected 2.5% level experienced over the past 2 yr. Of concern over the next several quarters, though, is the impact of the large over- hang of motor vehicles inventories on the economy. EMPLOYMENT The civilian unemployment rate declined to 6.636 in March after remaining at 6.7% for the previous 3 months. Employment continued to expand in February and March, although growth was significantly slower in March than in previous months. The manufacturing sector, however, lost 24,000 jobs in March after gaining 46,000 in February. Three-quarters of that gain came when striking workers at USX Corp. and Deere & CO. returned to their jobs. Employment in the manufacturing sectors of direct interest to the mineral industries has generally been increasing for at least the last quarter, while worker hours for these sectors have been on the upswing since April 1986 (figures 1 and 2).

Jan 1, 1987

Develop a safe, nonpolluting power source for underground mining equipment. Approach The Bureau of Mines and EIM-CO Mining Machinery International entered into a cost-shared project to develop and demonstrate a novel power source for mining. An underground mining utility truck was equipped with an ultra-low-emission hydrogen-fueled engine and a safe, metal hydride fuel storage system. How It Works The nonpolluting hydrogen engine and a "solid-state" (metal hyride) hydrogen fuel storage system were combined to power a utility mining vehicle. An 85 horsepower diesel engine was convened to burn hydrogen. The engine was converted by equipping it with a spark ignition, lowering the compression ratio, turbocharging, and adding an ahercooler and a parallel fuel induction system. Parallel induction provides two intake paths, one for hydrogen and one for air. It avoids intake-manifold backfiring by keeping the hydrogen and air separate until they enter the cylinder.

Jan 1, 1986

By Leonard Obert

Subsidence to surface occurs in a large proportion of underground mines. Preliminary to any indication of subsidence on the surface, there is usually a breaking up and sloughing of the cover into the mine opening which, in a period of time ranging from minutes to many years, progresses to the surface, This process is referred to as subsurface subsidence. In many mining operations, information regarding the process of subsurface subsidence is important, For example, if there are buildings or other improvements on the surface, or if the direction of the subsurface subsidence might threaten other underground workings--such as shafts--or if the subsidence might be progressing in a direction which would fall outside the anticipated subsidence limits, the problem could assume special significance.

Jan 1, 1961

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported J, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simplification to determine an economically feasible procedure that mould require a minimum of expensive equipment for plant erection and a minimum of regent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth Mile to utilize available facilities in a search for difficulties, that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 rounds per day of metal and operated under simulated -plant practice.

Jan 1, 1938

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By G. A. Crowder

Far infrared spectra, most of them in the region 15-200 microns and for both the liquid or solution state and for the vapor state, were obtained for twenty-seven compounds.

Jan 1, 1965

By P. N. Summerfield

This report describes the first phase of a general investigation designed to ascertain whether an electronic roof-testing device can be developed that will improve the ability to detect "loose" or "drummy" roof rock over that possible by striking the roof with a sounding bar and noting the character of the air vibrations with the unaided ear or the rock vibrations with the fingers. The amplitude, frequency content, and duration of the vibrations produced by striking solid and drummy roof rock with a hammer or sounding bar have been measured. Results disclosed that there is a significant difference between the characteristics of the vibrations produced in solid and drummy roof. This difference is such that the design of an electronic device to indicate quantitatively the condition of the roof rock appears possible. INTRODUCTION The conventional method of roof testing consists of striking the roof with a bar2/ and judging its soundness from the character of the air vibrations heard with the ear and/or the rock vibrations felt with the fingers -a procedure that depends upon the experience and the sensory abilities of the observer. Impact testing of a solid roof rock usually produces a sharp ping or click, whereas impact testing of a drummy roof rock produces a dull thud or drummy sound. This method of roof testing is, at most, only a qualitative test, and many roof rocks are difficult to classify as drummy or solid.

Jan 1, 1956

By Jack L. Henry

The ternary system A14C3-AIN-Al203 has been examined to determine compositions which may display desirable high-temperature refractory properties. Powder methods were employed in the synthesis of all test compositions. Forming and sintering behavior was examined and hot-pressing parameters were measured. Several properties were studied for each composition of interest in the system. The properties included hydrolysis rate in moist air, elevated temperature oxidation rate, density, softening point, tensile strength, and rupture strength. In most cases equilibrium was not achieved, and the data are representative of a nonequilibrium system. Approximately 16 separate phases have been observed in the system. Forming behavior and selected properties of five compositions of interest were compared with those of aluminum oxide and aluminum nitride. None of the compositions compared favorably. Oxidation and vaporization appear to be serious drawbacks to the use of these compositions at elevated temperatures.

Jan 1, 1969

By Harold J. Polta

This Bureau of Mines publication considers the feasibility of augmenting the present transportation system by pipelining taconite concentrates from the Mesabi Range to the Chicago area. The cost of pipelining in the hypothetical system using water as the carrier is estimated to be between $3.66 and $3.97 per long ton. This appears competitive with the 1970 rail-vessel transportation rate of $4.08 even after allowing a few cents per ton for barging from the terminal to existing furnaces. Political obstacles requiring solution before such a pipeline could be built and the feasibility of using crude oil as the carrier fluid are also discussed. FORTRAN routines used to calculate unit transportation cost for specific estimated values of cost items and for a range of values are presented. The effect of deviations from estimated values of cost items on the total unit transportation cost are shown graphically.

Jan 1, 1971

By J. B. Janus

In connection with the purchase of coal under specifications for Government use, the Bureau of Mines in this report has compiled data on 81 mines located in 15 States. This annual report lists analytical data on the composition and quality of tipple and delivered samples of coal collected during fiscal year 1973. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for most of the coalbeds listed. The deliveries were sampled at destination in accordance with instructions issued by the Bureau of Mines. All samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

By Robert J. Willard

This chapter includes tables from 1983 that were not available in time for publication of the 1983 Minerals Yearbook, but does not include corresponding tables for 1984. The value of raw nonfuel minerals produced in the United States during 1984 was estimated at $23.2 billion, an increase of $2.1 billion over the value for 1983. This is the second consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 12 out of 13 years. In 1984, 16 out of 21 metal commodities increased in output while 5 metals decreased; 14 metals increased in value and 7 decreased. Of 46 nonmetal commodities. 37 increased in output while 7 decreased and 2 remained unchanged; 35 nonmetals increased in value and 11 decreased. These statistics are grounds for continuing the cautious economic optimism expressed in 1983. Despite the note of optimism, however, numerous problems plague the mining industry, weakening its stability and inhibiting its growth potential. The problems are a complex mix of international and domestic factors that have been building in the recent past, but have become even more troublesome in 1984.

Jan 1, 1985

By C. A. Herbert

In summer, when hot, moisture-laden air enters a coal mine in the region east of the Mississippi River, the moisture is likely to condense on the roof and ribs because the incoming air is cooled below its dew point upon contact with the roof, ribs, and floor of the mine passageways. When the roof and ribs become wet owing to this condensation they are said to "sweat." In many mines, as soon as this sweating begins, shale or slate roof that appears solid and strong in winter begins to cut and fall. For a long time most mining men believed (many still believe) that the roof trouble was due to this sweating. However, from observation of conditions in one mine the operators concluded that the trouble was caused by expansion and contraction of the roof due to changes of temperature. This opinion was confirmed by experiments at several mines in cooling the air as it entered the mines. Methods used in these mines for cooling the air are described in this circular. MINE A At mine A the roof gave considerable trouble in the summer, and it was observed that where a spray of water from a leaking dam kept the roof wet and at a uniform temperature no difficulty was experienced with the roof, although it had cut and fallen on either side of that point. From this fact the company officials concluded that changes of temperature in the air rather than moisture caused the trouble and that if the incoming air were cooled to approximately normal strata temperature much of the additional roof trouble experienced during the summer would be overcome.

Jan 1, 1940

Senior staff representatives of the Bureau of Mines and the National Institute for Occupational Safety and Health (NIOSH) met in Washington on September 6, 1972, to review and evaluate their cooperative accomplishments to date and to consider the planning and conduct of future coordinated activities. The six presentations given at this joint staff seminar are published here for the benefit of those concerned with the problems of coal mine health, and especially those with responsibilities in administering the Coal Mine Health and Safety Act of 1969.

Jan 1, 1972

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Seth T. Reese

THE INJURY DATA and experience at coke ovens in the United States for 1952 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, frequency rates, and accident agencies involved in causing injuries. Data are given for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data in the coking industry covering 5- and 10-year periods on the number of injuries, accident agencies, and severity of injuries. (C) Historic injury experience: Tables 16 to 19: Contain data on the number of injuries, frequency rates, and employment at coke ovens from the earliest records through 1952, Operating statistics from 1929 through 1952 are given in table 19.

Jan 1, 1955