Search Documents

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By Mark S. Stagg, David E. Siskind

Five major environmental effects of rock blasting are ground vibrations, airblast, flyrock, dust and fumes. What makes them "environmental" as opposed to occupational health and safety issues is that their impacts are felt off the mine, quarry or construction site. For some impacts, safe zones are defined through experience, flyrock being a good example. Flyrock at a mine can be 1) rock thrown beyond the blast area or expected hazard zone, 2) rock thrown beyond the permit area, or 3) rock thrown more than 1/2 the distance to the nearest non-mine structure (OSM rule for surface coal mines). Rock throw of less than the "flyrock" range is then a safety issue.

Jan 1, 1997

By R J. Roach, D Roy

After months of discussion on ways and means to improve productivity in the shaft sinking process, it was decided to look at those areas where, historically, methods have been stagnant for many years. These categories included drilling, hole diameter, drill patterns, explosive types, explosive loads, initiation techniques, cut design, wall control, fragmentation and heated magazines.

Jan 1, 1997

By Michael S. Wieland

Delay detonators that are damaged by cross-hole wave interactions degrade blasting work and raise the risk of incidents. Damaged detonators impose risk, because they can retain sensitive explosives that respond to stray energy during recovery, inspection or disposal. Laboratory techniques were developed to rank the ruggedness of delay detonators under replicated field-shooting conditions. The hazards are tremendously magnified if trial detonators are installed directly in secondary explosives to rank initiation strength. Therefore indirect ranking techniques were sought that mitigate the risks without compromising the worthiness of the method. Four types of hardware fixtures, referred to as simulators, were developed to yield distinct forms of transient compression. The shock and rift versions generate compression pulses representative of in situ waveform components. The waiting time, until the trial detonator functions, duplicates typical delay periods. The trial detonator is mounted within water, which has a density and inertial resistance comparable to most blasting explosives. The work output from the trial detonator explosion is registered as fixture wall-expansion. This work output determines malfunction results, regardless of which type of simulator is used.

Jan 1, 1997

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997

By Tjaar A. Louw, Albert P. Van Niekerk, Johannes J. Louw, Attie J. Goosen

Unlike molecular high explosives, commercial explosives based on ammonium nitrate do not detonate ideally according to the theoretical model for steady state, one-dimensional detonation. One of the reasons for this deviation from ideal detonation is the slower chemical reaction, due to less intimate contact between the oxidiser and fuel components. It is well known that the inclusion of gas pockets, such as microballoons, in the formulation of ammonium nitrate based emulsions and watergels enhances the performance of these explosives. Various different interpretations of the “hot spot” theory have been proposed to explain this phenomenon.

Jan 1, 1997

By Zhao Jie, Christopher G. Smith

Commercial explosive use in China has been dominated by powdered AN-TNT mixes. Water gels and emulsions are now gaining market acceptance because they offer potential for better performance. Although raw material costs for emulsions initially may be more than AN-TNT mixes, the more expensive technology improves sensitization and leads to lower costs overall for mining operations. A recently completed study in northeast China compared microsphere-modified emulsions to AN-TNT and lower-cost emulsions. Testing of microsphere-modified emulsions at several pH levels indicated a high degree of stability and consistency of VOD. Using 42 mm blastholes in underground mines and 170 mm holes in sandstone open pit mining demonstrated the superior performance of glass microsphere sensitized emulsions. Comparisons of explosive cost, drilling cost, secondary blasting cost and muck pile profile were favorable to the microspheres-sensitized-emulsions. Noxious fumes with AN-TNT or with water-based systems that partially fail during detonation are also a concern. Efficient detonation of emulsion products sensitized with hollow spheres appears to reduce fume generation. Prolonged storage or exposure to water also is not a problem.

Jan 1, 1997

By Dennis Dobson, Keith M. Henderson

Lone Star Industries, Inc. in Cape Girardeau, Missouri operates an open pit mine to produce limestone for its portland cement manufacturing plant. The present mining method, for safety and legal reasons, requires a set back from the property line, a berm, sloped overburden, and vertical rock walls with catch benches.

Jan 1, 1997

By T Barnes, K D. Sexton, T J. Tope

For the past decade, the U.S. Department of Defense (DoD) has been under increasing pressure from state and federal regulatory authorities to develop management strategies for waste streams generated at its bases, installations, and ranges. Since passage of the Federal Facilities Compliance Act (FFCA) in 1992, concerns have focused in particular on military munitions and energetic waste streams.

Jan 1, 1997

By Jack Eloranta

This paper compares energy requirements for blasting, crushing and grinding. By tracking electrical consumption for various powder factors, a general trend has appeared. This study involves over 100 million tons of ore and powder factors ranging from .5 lbs/LT to .8 lbs/LT. Actual energy usage is compared to predicted energy based on the Bond equation.

Jan 1, 1997

"AQUILA Mining Systems Ltd. is a Canadian company that designs and develops monitoring, control and navigation systems for the surface and underground mining industries. In 1992, AQUILA Mining Systems began the development of technology for monitoring, controlling and positioning mobile mining equipment. In 1993, AQUILA completed its first field test with GPS receivers onboard ablasthole drill, and thus demonstrated the viability and strategic relevance of this technology in surface mining. Since then, AQUILA has installed GPS-based technology on drills and shovels in several Canadian mines. This paper will review the development of these systems and discussthe benefits the mining industry could realise through their production implementation."

Jan 1, 1997

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997

By Michael Noy

Current image based systems used to measure fragmentation are measuring the two dimensional presentation of a set of three dimensional objects. A two dimensional measurement of fragmentation restricts both sampling and particle size classification and hence provides a different evaluation of the fragmentation to that of a conventional sieve analysis of the same sampled material. Many modern image based fragmentation measurement systems attempt to convert this two dimensional analysis to a three dimensional analysis in order to deliver a "real" measurement of the fragmentation distribution. This paper questions the necessity and validity of this transformation and lays down the framework for the establishment of a standard in fragmentation measurement based on a two dimensional analysis. The results of image based measurements of laboratory prepared samples indicate that differences in mass distributions (3D distribution) can be mapped by an appropriate image based analysis which provides area versus particle size information.

Jan 1, 1997

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

By Jin Jingzhi, Wang Xuguang, Guan Li, Li Jianjin

Emulsion explosives are gaining a wider and wider commercial market and are displacing other composite slurry technologies. However, the grease-like state and essential thermodynamic instability of emulsion explosives cause inconvenience in production, transportation, storage and use and lead to gradual changes in performance. Emulsion powder explosives are designed to avoid these disadvantages. The formulation, process and properties of emulsion powder explosives made through a spin flash technology are described in this paper.

Jan 1, 1997

By C Deacon, M Jones, P Duniam

Electronic blast timing has been in use around the world since the mid-eighties, and, whilst it has yet to be used commercially by large operations on an ongoing basis, significant inroads have been made in niche areas where tighter control of blasting is required.

Jan 1, 1997

By Brian W. Stump, David P. Anderson, John Wiegand

Mining explosions are designed for a variety of purposes including the fragmentation and movement of materials. The blast design is dependent on the particular application intended and the material properties of the rock. The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices.

Jan 1, 1997

By Daryl Andershock, Paul Worsey, Brandon Weeks, Kurt Kosman

Several derivatives of soybean oil are currently manufactured and sold on the open market. Of these, the use of methylsoyate as a direct fuel substitute in diesel engines has been thoroughly researched and practically applied. The use of this product as a fuel gave rise to the idea of using a similar substitution in ANFO blasting agent. The first year of a three-year research program has been sponsored by the Missouri Soybean Merchandising Council. The project is funded for the purpose of opening up of new markets for Missouri soybean products.

Jan 1, 1997