Search Documents

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By A. Koster, V. Maurel, S. Dezecot, Szmytka. F.

The aim of this work is to clarify the role of microstructure heterogeneity in the initiation and growth of cracks in a lost foam cast A319 for low cycle fatigue (LCF) loading condition. Because 2D analysis fail to establish the scenario of damage events, this study is based on 3D in situ analysis using synchrotron X-ray tomography during LCF test performed at 200°C. If X-ray tomography is now an established technique to study damage development in 3D, its application for relatively high temperature cyclic tests has never been done so far. Initial 3D observations of damage show that the cracks that lead to fracture initiate near large pores and propagate into the hard particles 3D network of the eutectic regions.

Jan 1, 2015

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By E. Ghali, W. Zhang, G. Gabra, N. Sorour, G. Houlachi

The additives polyacrylamide, 1-Butyl-3-methylimidazolium chloride, Tetra-butylammonium bromide, Benzalkonium chloride and chitin are evaluated during zinc electrolysis from synthetic acidic sulphate electrolyte containing Mn2+ ions, in absence and in presence of 0.0055 mg dm-3 of Sb3+ ions. Galvanostatic polarization tests for 2 hours at 50 mA cm-2 and 38oC were carried out to determine the cathodic and anodic potentials, and current efficiency of the deposited zinc. Potentiodynamic polarization and cyclic voltammetry tests have also been employed to study the electrochemical behavior of each additive on the zinc deposit on aluminum electrode. Results showed that, in presence of Sb3+, adding 1 to 3 mg of 1-Butyl-3-methylimidazolium chloride increases the cell voltage by ˜0-7 mV. Current efficiency is increased by ˜4.90-6.40%; power consumption is reduced by ˜147-173 kWh t-1 by adding 1-3 mg, respectively. However, in absence of Sb3+, cell voltage is decreased by ˜7-28 mV, current efficiency is increased by ˜0.70-1.50%; power consumption is reduced by ˜41-47 kWh t-1 by adding 1-3 mg. The effect of the other additives on cell voltage, current efficiency, lead content and morphology of zinc deposit has also been examined. Surface morphology and crystallographic orientation of the deposit was studied using scanning electron microscopic (SEM) and X-ray diffraction (XRD), respectively. The content of lead in the deposit has also been measured using inductively coupled plasma spectroscopy (ICP).

Jan 1, 2015

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By P. Schmidt, M. Hopf

Water-cooled parts of submerged arc furnaces are potentially dangerous, especially if molten matte or slag contacts the water. Explosion hazards and metal run-outs generate high costs for production loss and repairs - not mentioning the possible loss of human life. This paper reports about practical results of wear measurement on intensive water-cooled tap-holes and spray-cooled side walls. On the one hand an embedding technology has been developed, that is used e.g. in water-cooled copper tap blocks or copper side wall coolers. Second the application of the sensor installation on the inner side of a water-cooled steel shell will be discussed. The fibre-optic sensor is fed through a specially arranged piping system and measures numerous temperatures over its entire length. By using the thermal conductivity of the installed refractory materials the lining thickness is calculated. The practical installation of the sensors will be discussed and the results of the wear measurement will be compared to the theoretical FEM calculations. The highly sensitive and accurate temperature measurement, as well as the recalculation of the impact of differences in the cooling water temperature, allows the exact determination of the remaining lining thickness. The discussed technologies offer efficient and safe monitoring of tap-holes, side walls and other endangered parts of pyro-metallurgical smelters.

Jan 1, 2015

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

"The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle.When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice. INTRODUCTIONThere are a lot of joints and fractures in surrounding rock mass of deep-lying in the Jinping-II hydropower station, which has a great influence on the physical and mechanical properties of rocks and effects the acoustic wave propagation and attenuation law in rock. Many previous research and project examples has proved that sound propagation parameters are closely related to crack and stress condition. Thus, it has certain theoretical significance and practical application value to carry out researches on sound propagation characteristics and establish damage constitutive model of fractured rock mass which is related to sound propagation parameters."

Jan 1, 2015

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By Iain Sommerville, Hugh Mountford, Dawid D. Smith, Claude Dube, Brett Hixson

JW Aluminum use lean and Six Sigma techniques to continuously improve their target of reliable, repeatable and reproducible (3R) manufacturing. Six Sigma’s second stage gate, known as "Measure" involves identification and qualifying appropriate measuring systems. Metal quality (inclusions) are known in the industry to be an important element in 3R casting. The measurement of inclusions at JW Aluminum historically depended on outside vendors. In order to establish real time inclusion measurement ability within JW Aluminum, inclusion measurement systems in the marketplace were investigated. The qualification of a MetalVision MV20/20 ultrasonic inclusion analyzer are discussed as well as the subsequent application of the system in melting and casting improvement projects.

Jan 1, 2015

By Xing-Liang Sun, Xian-Min Han, Zheng-Guo Zhu

The study on the material properties of frozen soils in China was being developed quickly in the past decades of years, because of the increase of the engineering constructed in frozen soil regions on the Qinghai–Tibet Plateau, and numerous research results were achieved mainly about strength and deformation behaviour and constitutive models of frozen soils. Studies have shown that the deformation procedure of frozen soils is irreversible; therefore, it is more appropriate to research mechanical properties of frozen soils by means of damage mechanics theory. In this paper, an elasto-viscoplastic anisotropic damage model is presented by introduction of Perzyna viscoplastic equation into analyzing the deformation of frozen soil. In addition, an anisotropic damage evolution equation is obtained by means of extending non-viscous damage to viscous damage. Triaxial tests at different strain rates are chosen to illustrate the application of this model, and good agreement between experimental data and numerically simulated results is obtained. The calculated results indicate that, under the same conditions, the damage at higher strain rate is less than that at low one. So the phenomena are explained from damage mechanics that the frozen soil has larger elastic modulus and shear strength at higher strain rates, and explained from mechanism that the emergence and development of micro-cracks in the body of frozen soil can be to some extent retarded at higher strain rates.

Jan 1, 2015

By Guojun Wang, Zejun Chen, Wenchang Liu

Al/Mg/Ti laminated metal composite sheet (LMCS) can combine the merits of each of metal components, and obtain excellent performances. It incorporates the advantages of high strength, light weight, easy melt and atomization, and good space adaptability to substitute for the bumper Al sheet of Whipple shield structure for space debris shield. The Al/Mg/Ti LMCS was fabricated by hot roll bonding technology in a certain sequence. The manufacturing process and parameters were analyzed and studied, including the first rolling reduction, roll boding temperature and stacking structure of each metal. The microstructure of dissimilar metals and bonding interface were characterized and analyzed. The optimized manufacturing procedures and parameters were presented based on the microstructure and mechanical properties of LMCS. The research results offer some guides and references for controlling the shape of bonding interface, optimizing the annealing process, improving the mechanical properties of Al/Mg/Ti LMCS.

Jan 1, 2015

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015