Search Documents

By Shae K. Kim

The aim of this study is to manufacture magnesium alloys with alkaline earth metal oxides (BeO, CaO, MgO or SrO) additions with the objectives of (1) ensuring safety during processing and applications by raising the ignition temperature and reducing oxidation, (2) protecting the environment by reducing or eliminating use of protective gases, (3) maintaining or improving elevated temperature properties with lower amount of Ca or Sr or rare earth metals when compared with conventionally developed high-temperature magnesium alloys, (4) developing cleaner strip casting and continuous casting processes without hot tearing and (5) obtaining all of these objectives without sacrificing mechanical properties or increasing the cost of magnesium alloys.

Jan 1, 2006

By C. Kuehmann, B. Tufts

QuesTek Innovations has applied its Materials by Design® methodology to computationally design a new ultra high-strength corrosion resistant steel. Ferriurn® S53 eliminates the need for toxic cadmium coatings currently used on conventional steels in landing gear systems. S53 has the strength of 300M steel, and corrosion resistance similar to 15-5PH stainless steel. S53's corrosion resistance improves stress corrosion cracking resistance and reduces susceptibility to hydrogen embrittlement, improving component reliability and providing an opportunity for extended overhaul and repair intervals. Ultimate tensile stress is 1965 to 2000MPa. S53 was designed to be mechanically equivalent to 300M, with the key addition of intrinsic corrosion resistance. Alloy design, microstructural characterization, and mechanical properties are discussed herein.

Jan 1, 2006

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By K. Östcrdahl

We are developing a cost-saving and environmentally friendly process with low energy consumption to recover the metal content and recycle the acid from spent pickle baths. The metals are precipitated as metal fluorides, which can be turned into metal oxides and hydrofluoric acid by thermal hydrolysis. In the proposed process the solution is concentrated by nanofiltration and the metals are precipitated in a subsequent crystallization step. Different nanofiltration membranes have been evaluated in experimental batch tests. The membrane MPF-34 from Koch Membrane Systems offered both good flux and acceptable metal retention even after long periods of acid storage. The solubility of B-FeF3.3H20 has been measured at varying acid concentrations and at different temperatures. The solubility decreases with increasing hydrofluoric acid and nitric acid concentrations. This suggests that the crystallization process should be operated at high acid concentrations. The crystal growth rate of B-FeF3.3H2O is found to be quite low but increases significantly with temperature. This suggests that the crystallization process should be operated at higher temperatures (40 - 60°C). Within the project a pilot plant has been constructed where the spent pickle bath solution is concentrated by nanofiltration to the desired metal fluoride supersaturation, and B-FeF3.3H2O is crystallized in a 10 L continuous crystallizer.

Jan 1, 2006

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By G. Binks

In 1997, the Zinifex Hobart Smelter ceased ocean disposal of jarosite and the flowsheet was converted to reject iron as paragoethite. This paper describes the evolution of the flowsheet since the changeover and considers future flowsheet developments. The major change to the flowsheet has been an increase in the silica content of the calcine resulting from treating increasing levels of Century concentrate. The high silica levels impacted on the paragoethite precipitation stage, causing a deterioration in the settling and filtration characteristics of the paragoethite and an increase in the contained zinc level. The implementation of a two stage neutral leach step has enabled the flowsheet to cope with the higher input silica levels. Future developments include an understanding of the form of the zinc in the paragoethite and options to lower the zinc level to improve the overall zinc recovery.

Jan 1, 2006

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By N. E. Izatt

Molecular recognition technology (MRT) has a wide range of applications in the hydrometallurgical and chemical processing industries for the selective removal of iron as well as various other impurities from a variety of streams, including aqueous solutions through a wide pH range, as well as organic solutions. An example of a commercial application is provided for the removal of iron from an aluminum chlorohydrate stream. In this example, MRT has a selectivity for iron relative to aluminum which is significantly higher than that of ion exchange resins. A discussion of MRT capabilities for other impurities and streams is also provided.

Jan 1, 2006

By L. Gasser, N. Bellinger, H. Awatta, A. Merati

As aircraft age, the extent of interactions between fatigue and other damage mechanisms, such as corrosion and fretting, increases. At present, however, there is no generally accepted methodology within the Aircraft Structural Integrity Program (ASIP) framework to account for the effects of these interactions on life and the residual strength of aging aircraft components. A comprehensive program is being carried out by the National Research Council Canada in collaboration with Analytical Processes/Engineered Solutions, using the Holistic Structural Integrity Process (HOLSIP) to address time and cyclic load issues. This approach predicts the evolution of a discontinuity state in a material from production to retirement. This paper summarizes the results of a study on the 2024-T3 aluminium alloy in different forms (clad and unclad), thickness, and specimen geometry. This study consisted of identifying the microstructural features associated with crack nucleation sites and relating them to the testing parameters and fatigue life. Several coupons were fabricated and fatigue-tested. The fracture surfaces were carefully examined, and the physical characteristics of the microstructural features found near the crack nucleation sites were analyzed. Effect of stress level, loading direction, coupon geometry and surface condition on the number of crack nucleation sites, and fracture origin size has been discussed. Four distinctive mechanisms were found to be responsible for crack nucleation: for unclad materials constituent particles, oxide residue, surface irregularities and for clad samples the clad layer was the sole fracture origin.

Jan 1, 2006

By M. Imamura

Sumitomo Metal Mining Co., Ltd. has developed a novel hydrometallurgical process for producing not only copper metal but also iron metal from copper concentrates. Because copper concentrates generally contains the same amount of iron as copper, cost-effective rejection of the iron is a key issue for the development of the process. Conventional hydrometallurgical processes produce a large volume of goethite or hematite for disposal and the residues are not environmentally friendly. In the novel Sumitomo hydrometallurgical process, copper is leached effectively from chalcopyrite concentrates using chlorine gas, followed by purification through solvent extraction and electrowinning for copper and iron recovery. This process has many advantages such as the minimization of the volume of solid waste by the recovery of metallic iron and the production of high purity copper. Iron metal with a purity of more than 98% can be recovered from the purified raffinate. This paper presents the results of the batch and continuous tests of the process flowsheet.

Jan 1, 2006

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006