Search Documents

The paper describes the geology, structure, stress, gas and strata geomechanical properties for Leichhardt Colliery and their reactions to mining.

Jan 1, 1986

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

Ore petrology will fundamentally determine the types of metallurgical processes employed for ore treatment, their operational efficiency and the nature of processing problems encountered. It is therefore paramount that the petrological charact

Jan 1, 1998

By J Manuel, L Lu

Increasing bed depth is one of the main options sinter plants consider to increase production, since it is an incremental improvement and less expensive compared with a new plant. To maximise the benefits of increased bed depth, correct blend design and plant operation is critical. This paper discusses test work conducted to show the effects of ore type and bed depth on sintering performance and the adjustments required in both fuel rate and lime addition depending on ore type. The differences in sinter plug macro and microstructure were also examined to show the effect of bed depth on ore assimilation and matrix formation. Finally, the benefits of blending ores to achieve the best sintering performance as bed depth increases is discussed.

Jan 1, 2007

By G T. Hefter, P Singh

The effect of using SO2 as an anodic depolariser in the electrowinning of copper from aqueous acid sulphate solutions has been studied using cells without/with a ceramic diaphragm. In all cases SO2-saturation of the electrolyte/anolyte decreased the anode potential by 68 to 75 per cent largely due to a change in the anode reaction from the oxidation of water to the oxidation of SO2 . However, poor quality deposits and low current efficiencies are encountered if SO2 is allowed free-access to the copper being deposited at the cathode. This situation is easily avoided by using a diaphragm to restrict SO2 to the anode compartment and for these conditions the resultant copper deposits are of a similar (high) quality to those obtained in the absence of SO2.

Jan 1, 1999

By Gupta A, Hall ST

The grinding characteristics of quartz which is normally associated with gold bearing ores in Kalgoorlie area was examined in a stainless steel laboratory size ball-mill in the presence of inorganic and organic surface active reagents. The cationic species considered were Fe3+, Cu2+ and Ca2+, and the anions were CO? and S2 as these are normally present during the process of grinding of gold ores in the region. The organic surfactants examined were K-amyl- xanthate, dodecylamine-hydrochloride and the Grinding Aid XFS-4272 manufactured by Dow Chemical The study was primarily based on an examination of the electrokinetic properties of quartz surface in the presence of the grinding reagents. Zeta potential at different reagent additions and pH values in the presence of individual reagents were examined and the corresponding grinding charcteristics determined. A correlation has been indicated between the grinding characteristics, as measured by the -53um size fraction produced, and the surface energy of quartz. It was observed that an

Jan 1, 1978

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

By Grouhel P

Blasting performance is directly related to the characteristics and efficiency of the explosives used. The selection of the correct explosive for particular blast conditions and objectives depends on the ability to characterise the performance of individual explosive products. Techniques have been developed by the JKMRC to measure explosive performance and assess the impact of explosive performance on blast results. Studies conducted at a number of mine sites have shown that different types of explosives perform quite differently and that the performance of any particular explosive can vary significantly. The principal causes of these variations have been identified and detailed blast monitoring techniques, including the analysis of muckpile fragmentation and shape, have been used to quantify the effects of explosive performance on blast Results.

Jan 1, 1990

By Hayes P. C

In commercial mineral processing operations it has been found that the conditions in the drier have a considerable effect on the subsequent electrostatic separation of nttile and zircon. Laboratory scale studies simulating these heat treatment processes have shown that the electrical conductivity of nitile varies markedly with treatment temperature, time and gas composition. The zircon on the other hand is unaffected. By increasing the electrical conductivity of the rutile, significant increases in separation efficiency can be achieved. Electron microscope investigations have shown the increase in electrical conductivity to be associated with the production of planar defects in the crystal lattice.

Jan 1, 1991

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

The different electrowinning cells presently developed for recovery of gold from CIP eluates are compared and contrasted. The efficiency of operation for each cell is,discussed in terms of the electrochemistry of (a) gold deposition, and (b) packed bed electrodes. The advantages and problems associated with each cell design are presented and recommendations are made as to the best method of gold recovery.

Jan 1, 1982

This paper discusses basic practices of operation applied to raise drilling. It draws attention to critical areas that tend to be neglected. A brief history covers development of raise drills. The elements of the equipment, derrick assembly, drill string and reamers are ex- amined. Particular emphasis is on the drill string. It is concluded that manufacturer and operator can benefit each other by closer interchange of ideas.

Jan 1, 1977

Minerals processing needs a step change in energy efficiency. While the search for new technology breakthroughs is important, huge gains are still available by better using existing research outcomes. This potential remains untapped due to a combination of organisational 'silos', inappropriate performance measurement, and poor science in some areas. It is time to see the elephant in the mill.

Sep 13, 2010

By Kershaw M. G, Maughan R. C A

A process for eliminating nickel from electrolytic zinc plant solutions by precipita- tion with dimethylglyoxime (DMG) was developed to enable the Electrolytic Zinc Company of Australasia Limited (EZ) to treat nickel-bearing zinc dust precipitates. These precipitates are leached to recover their Cd and Zn content. The final Zn bearing solutions contain relatively high Ni concentra- tions (20-100 mg/1) and are treated with DMG and then neutralized to pH 4.6-4.8. The pre- cipitate is filtered off and the solution returned to circuit. DMG consumption is about 200% of theo- retical requirement, and Ni removal is 80% complete overall.

Jan 1, 1977

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By C G. Sweeney

The underground mining industry is seeing unprecedented shortages in skilled labour. Migration to Australia being at an all-time low is a leading concern, with pandemic-induced border closures and lockdowns only exacerbating the skills shortage, not causing it. The skills shortage is forecast to peak in 2023 and remain high beyond 2025. With this skills shortage in mind, mining companies throughout Australia are trying to deal with stricter protocols around Health and Safety (H&S) legislation, as well as more stringent controls on quality assurance, particularly as underground mines are reaching greater depths and extending into ‘unchartered territory’. The cumulation of this is proving to be a major hurdle in ‘effective’ operational geotechnical management. The drive for automation in mining is bringing another level of complexity. However, ‘once automation is up and running, it presents the opportunity to access talent pools that may not normally be available. There is also a change in skillset that will be required to drive automation. ‘The top two emerging roles that will be critical for the future of the mining industry are artificial intelligence and machine learning (AI/ML) specialists, and process-automation specialists’ (Writer, 2021). If anything positive has come from the pandemic, it has shown that remote working can be effective and that the drive for automation and critical evaluation of skills required on-site should be given greater priority. UQ acknowledges that the industry is changing, and that digital technology is required to be offered in mining related disciplines. Industry and academia need to do more to promote geotechnical engineering in mining and balance the curriculum to suit the future of mining and make it more enticing. The average cost of a geotechnical failure is about $5 million in coalmines and can be into the hundreds of millions of dollars if production is affected (Cartledge Mining and Geotechnics, 2020). The cost of a good geotechnical design far outweighs the potential losses if a failure were to occur. This alludes to the growing importance of experienced geotechnical consultancies playing a pivotal role in managing mine site geotechnical hazards, while the industry is developing the next generation of geotechnical engineers.

Nov 29, 2022

The Earth Moving Equipment Safety Round Table (EMESRT) was established by mining companies in 2006 to influence manufacturer's equipment design through a process of engagement. 2010 EMESRT member companies include Anglo American, Barrick, BHP Billiton, Centennial Coal, Collahausi, Newcrest, Newmont, Rio Tinto, Vale and Xstrata.Driven by a persistent need for retrofits to new equipment, such as haul trucks, EMESRT initially engaged with Surface Equipment Manufacturers including Caterpillar, Komatsu, Leibherr, Hitachi, Le Tourneau and Terex. These OEMs responded positively to the EMESRT initiative, welcoming the opportunity for dialogue with an aligned industry regarding human factors issues related to equipment design, rather than needing to respond to the disparate range of demands for design modifications previously received from individual customers. This engagement process is about making global sustained changes within the OEM organisations and within the mining companies. It is a very international exercise. For example, over two weeks in September 2010, a total of 21 different miners from ten different companies travelled from Australia, South Africa, Canada, Brazil, Singapore and the United States to engage with OEM counterparts who assembled from the United States, Japan, France, Sweden, Finland and Germany. EMESRT Surface Group representatives completed a whirlwind tour of the major North American manufacturers of mining equipment. Starting in Dallas (Atlas Copco, LeTourneau), this tour passed through Gainesville (Sandvik), Newport News (Liebherr), Guelph - Ontario (Hitachi) and Milwaukee (P&H Mining/Joy Global; Bucyrus), before winding up in Peoria, Illinois (Komatsu, Caterpillar). Over nine meetings, this group engaged with 129 individuals from nine OEMs. The EMESRT group welcomed miners from four non-member companies to come along for the meetings. These companies are Syncrude Canada Ltd, the Kearl Oil Sands Project - Imperial Oil (ESSO), Suncor Energy Ltd and Teck Resources Ltd.Other mining industry sectors have now expanded the EMESRT scope from surface mining to include exploration and underground mining equipment. In 2009, EMESRT was organised into four Technical Groups, consisting of EMESRT member company representatives, to focus on engagement with OEMs of surface, underground coal and soft rock, underground hard rock, and exploration drilling equipment. An advisory group has been formed to coordinate activities between all workgroups and provide strategic direction and cohesion between all activities. The Minerals Industry Safety and Health Centre (UQ-SMI) facilitates and coordinates all EMESRT activities on behalf of member companies. Building on successes with individual Surface Mining OEMs, EMESRT now aims to help OEMs in their transition to a sustainable design process that will incorporate and address specific design philosophies at the concept phase of design, so that significant improvements can be made up front for little cost within the overall budget. EMESRT members plan to educate all stakeholders, internally, within their own companies, and externally, by addressing industry associations, regulators and other end users about new ways of evaluating equipment design based on EMESRT purchasing specifications. This presentation will outline the EMESRT approach and report on progress in 2010.

Dec 6, 2010