Search Documents

By M. A. Torcaso, P. Raimondi

The distribution of the oil phase in Berea sandstone resulting from increasing and decreasing the water saturation by imbibition was investigated Three types of distribution were recognized: trapped, normal and lagging. The amount of oil in each of these distributions was determined as a function of saturation by carrying out a miscible displacement in the oil phase under steady-state conditions of saturation. These conditions were maintained by flowing water and oil simultaneously in given ratios and by using a displacing solvent having essentially the same density and viscosity as the oil. A correlation shows the amount of trapped oil at any saturation to be directly proportional to the conventional residual oil saturation Sor The factor of proportionality is related to the fractional permeability to the water phase. Part of the oil which was not trapped was displaced in a piston-like manner (normal part) and part was eluted gradually (lagging part). The observed phenomena are more than of mere academic importance. Oil which is trapped may well provide the fuel essential for forward combustion and thus be beneficial. On the contrary, in tertiary recovery operations, it is this trapped oil which seems to make current techniques uneconomic. INTRODUCTION A typical oilfield may initially contain connate water and oil. After a period of primary production water often enters the field either from surrounding aquifers or from surface injection. During primary production evolution and establishment of a free gas saturation usually occurs. The effect and importance of this third phase is fully recognized. However, this investigation is limited to a two-phase system, one wetting phase (water) and one non-wetting phase (oil). The increase in water content of a water-wet system is termed imbibition. In a relative permeability-saturation diagram such as the one shown in Fig. 1, the initial conditions of the field would be represented by a point below a water saturation of about 35 per cent, i.e., where the imbibition and the drainage curves to the non-wetting phase nearly coincide. When water enters the field the relative permeability to oil decreases along the imbibition curve. At watered-out conditions the relative permeability to the oil becomes zero. At this point a considerable amount of oil. called residual oil, (about 35 per cent in Fig. 1) remains unrecovered. Any attempt to produce this oil will require that its saturation be increased. In Fig. 1 this would mean retracing the imbibition curve upwards. In addition, processes like alcohol and fire flooding, which can be employed at any stage of production, involve the complete displacement of connate water and an increase, or imbibition. of water saturation ahead of the displacing front. Thus, in several types of oil production it is the imbibition-relative permeability curve which rules the flow behavior. For this reason a knowledge of the distribution of the non-wetting phase, as obtained through imbibition, whether "coming down" or "going up" on the imbibition curve, is important.

Jan 1, 1965

By Frank E. Woolley, Robert D. Pehlke

Jan 1, 1965

By V. M. Karve, K. K. Majundar, K. V. Viswanathan, J. Y. Somnay

The effect of calcium, magnesium, iron (both ferrous and ferric) and aluminum ions, which are commonly encountered in a typical beryl ore, was studied in the flotation of pure beryl, soda-feldspar and quartz. The vacuumatic flotation technique was employed. With sodium oleate as collector and in the absence of any activator, beryl floated in a pH range of 3 to 7.5, whereas feldspar and quartz did not float at any pH up to 11.5. The pH range of flotation increased in the presence of the ions studied. With calcium and magnesium ions beryl floated from 3 to 11.5 pH and beyond, soda-feldspar floated beyond pH 6 and quartz floated beyond pH 8. Ferrous ion activation was found to be similar to that of calcium and magnesium. Activation by ferric and aluminium ions was found to be complex and the lower and upper critical pH for all the three minerals was around 2 and 10 respectively. These studies indicated the possibility of separation of beryl from feldspar and quartz even in the presence of calcium, magnesium and ferrous ions between pH 4 and 6. Flotation tests on a mixed feed of pure minerals in a 10 g cell revealed that beryl can be selectively floated from feldspar and quartz if ferric ion is reduced to ferrous state or if it is complexed. Beryl occurs mostly in pegmatites, and hence is associated with feldspar, quartz and micas and small amounts of other minerals such as apatite and tourmaline. The separation of beryl from these minerals is difficult because all the silicates accompanying beryl have more or less the same physical properties. Specific gravities of beryl, feldspar and quartz are 2.70, 2.56 and 2.66 respectively. Electrostatic separation has been suggested but no work has been reported. ' The adsorption of sodium tri-decylate tagged with Cl4 on beryl, feldspar and quartz reveal similarity in surface properties. Much work has been reported on the flotation of beryl from ores, either directly or indirectly as a by-product, but little is known about the fundamental aspects of beryl flotation. Kennedy and O'Meara3 laid emphasis on prior cleaning of the mineral surfaces with HF. Mica is removed first by flotation of beryl with oleic acid, around neutral pH. Runke4 introduced calcium hypochlorite conditioning in a final separation stage for activating beryl in a mixed beryl-feldspar concentrate, and after washing to remove the hypochlorite, floated beryl with petroleum sulphonate. The Snedden and Gibbs5 procedure is somewhat similar to that of Kennedy and O'Meara. Emulsified oleic acid is used as collector. Recently Fuerstenau and Bhappu6 studied the flotation of beryl, feldspar and quartz with petroleum sulfonate in the presence of activators and stressed the importance of iron in the flotation of beryl. From the studies conducted in this laboratory, it was found that feldspar and quartz as such do not float with sodium oleate, but in practice selective flotation of beryl from feldspar and quartz in an ore is found to be impossible with sodium oleate as collector. A glance at the chemical analysis of typical beryl ore indicates the presence of several ions like Ca ++, Mg++, Al + + + and Fe+++ in abundance and Ti++++ and Mn++ in traces. Hence, in an attempt to explain the behaviour of feldspar in the beryl flotation, the effect of Ca++, Mg++, Al+++ and Fe+++, which are known as gangue mineral activators7'8 has been investigated. Materials and Methods: Lumps of beryl ore (hand picked) were boiled with 10% sodium hydroxide and washed with distilled water. They were further boiled many times with 10% hydrochloric acid till no positive test for iron was obtained with ammonium thio cyanate. This was followed by thorough flushing with double distilled water. The lumps were crushed in a porcelain mortar and pestle under water. The minus 65 + 100 mesh fraction was used for testing and was always stored under distilled water. Pure feldspar and quartz were similarly prepared and the minus 65 + 100 mesh fractions collected. Inorganic ions tried as activators were ca++, Mg++ , Fe++, Fe ++ and A1 +++ . Calcium nitrate, magnesium chloride, ferrous ammonium sulfate, ferric ammonium sulfate and aluminum nitrate of G.R.E. Merck grade were used. B.D.H. technical grade sodium oleate was used as a collector. The vacuumatic flotation technique developed by Schuhmann and Prakash was used for studying the effect of pH on flotability. 7 The indications given by this work were confirmed by using 10 g miniature cell.'

Jan 1, 1965

By C. A. Queener, W. L. Mitchell

In recent years bismuth telluride has received considerable attention, primarily due to its value as a thermoelectric material. Since there seems to be little dependence of thermoelectric effect upon crystal orientation1 many of those who have previously worked with this material have been unconcerned with knowing its crystallographic angles to any degree of accuracy. However, when one studies deformation modes, lattice stresses, or the aniso-tropy of mechanical properties of a material, knowledge of the interplanar angles and their relationships as depicted in a stereographic projection becomes essential. Lange2 originally published crystallographic data which described the structure of bismuth telluride as rhombohedral with the space group A more recent work by Francombe3 presented data which corroborated and refined the original findings of Lange. In addition, Francombe established that there is no coexistence of rhombohedral and hexagonal lattices in bismuth telluride as was suggested by Vasenin and Konovalov,4 and that the structure can be treated as a pseu do hexagonal structure with an axial ratio, c/a, of 6.95 for convenience of presentation and study. The interplanar angles and standard projections for several unalloyed hexagonal metals have been previously published,5-9 but the present work appears to be unique in that it presents data for a rhombohedral compound in pseudohexagonal form. As a pseudohexagonal structure, this material has an extremely large axial ratio as compared to the usual range of approximately 1.5 to 1.9 for the hexagonal metals. Since the interplanar angles are a function only of c/a, the angular relations between various planes for Bi,Te3 will be grossly different

Jan 1, 1965

By H. J. Beattie

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By D. A. Thomas, M. F. Comerford

Poly crystalline wires of Fe-3.2 wt pct Si were cold-drawn to 31, 66, and 87 pct reductions of area. Mechanical properties and tnicrostructures were studied after recovery and re crystallization. An initial increase in strength during recovery was ascribed to strain aging, and subsequent softening was largely due to polygonization rather than re-crystallization. No unique actioation energies could be determined for the recovery process. Rather, activation energies ranged from 60,600 cal per mole at 10 pct recovery to 83,200 cal per mole when recovery was 50 pct complete. Sites for the nucleation of recrystallization were found to depend on time and temperature. In the early stages of re-crystallization, nucleation occurred in deformation hands. Later, or at high temperatures, recrystal-lized grains were nucleated primarily al grain boundaries. Polygonized structures did not seem to be preferred sites for nucleation. MUCH of the research on deformation, recovery, and recrystallization processes in bcc materials has been performed on single crystals or lightly worked polycrystals. Little study has been devoted to the relation of mechanical properties to micro-structure in polycrystals after severe deformation and subsequent annealing. This paper presents the results of a study of the tensile properties and microstructures of Fe-Si wires drawn varying amounts and annealed at a series of temperatures. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of the following composition: 3.2 wt pct Si, 0.08 Mn, 0.016 C, 0.005 0, 0.0002 N, 0.0001 H, 0.008 P, 0.034 S. The material was received as l-in.-sq bars cut longitudinally from a hot-rolled slab provided by the Armco Steel Corp. The bars were forged to 3/8-in. rounds, centerless-ground to 0.250 in., and swaged to '0.108 in. All subsequent reductions were performed by room-temperature wire drawing at the rate of 2 in. per min. Each preliminary draft gave approximately 30 pct reduction of area and was followed by a l-hr anneal at 1010°C in dry hydrogen. Three lots of wire were made with ultimate cold reductions of 31, 66, and 87 pct reduc-

Jan 1, 1965

By S. Zador, C. B. Alcock, K. Sudo

Measurements have been made of the standard free enevgies of formation of the sulfates of cobalt, Cupric copper, nickel, and ferric iron in the temperature range of 750° to 950°C. Dynamic gas-solid techniques have been employed in which oxide-sulfate and basic sulfate mixtures were placed in a stream of gas of controlled SO3 potentials. Thermal analysis and thermogvavimetry were used as detection methods, and it was found THE formation of sulfates during the roasting of sulfide ores is now considered to arise in many cases from the interaction of sulfur trioxide in the gas and the metal oxide which is formed on the sulfide as a first step.' As a preliminary to the investigation of the kinetics of sulfate formation during roasting, measurements have been made of equilibria from which the free energies of formation of cobalt, copper, nickel, and iron sulfates can be that the range of temperatures which could be investigated and the choice of method was largely controlled by the kinetics of these gas-solid reactions. The results are compared with previous results obtained from static measurements with which they agree quite well, and calculations have been made employing themal data to interrelate the present results with those for other sulfates. calculated. The method used has been to expose the solid sulfate (or basic sulfate) to a controlled flowing gas mixture of SO,, 02, and SOs and to observe the temperature of decomposition. The onset of decomposition was detected by thermal analysis or thermogravimetry. EXPERIMENTAL METHODS The thermal-analysis method was similar to that employed by Dewing and Richardson.' The sulfate was dehydrated at 250°C in air, and placed in a small alumina crucible which was held by a quartz ring in the hot zone of a horizontal furnace. The reaction tube of this furnace was made of mullite.

Jan 1, 1965

By Henry Leidheiser, Melvin C. Jr. Hobson

The rate of formation of the intermetallic compound, indium antimonide, at the interface between iudium and antimony at 100°C is greatly increased when a composite electrode of indium electrode -posited on antimony is made the cathode in an electrolytic cell. The amount of indium antimonide formed during electrolytic treatment at constant potential appeared to he proportional to the square root of time, but the scatter of the data, particularly at long times, makes it impossible to state this conclzlsi1:ely. The rate constant for the electrochemical synthesis was estimated to he 1.5 x 10-12 sq cm per sec. A similar- set of experiments was conducted in the absence of an applied potential but under otherwise similar conditions. The rate constant lor the thermal synthesis was less than 2 x 10-14 sq cm per, sec, at least two orders of magnitude less than obtained during electrolytic treatment. In a series of electrochemical studies it was observed that intermetallic compounds formed on the surface of polarized electrodes.1'2 The possibility of using this technique for the electrochemical preparation of intermetallic compounds was investigated and subsequently applied to the synthesis of the semiconducting III-V compounds. Gallium antimonide, indium arsenide. indium antimonide, and indium bismuthide were successfully formed by electrodepositing the Group III element from a boiling acid solution onto an electrode made of the Group V element. The following kinetic studies were undertaken on indium antimonide to obtain quantitative information on the rate of formation of this representative III-V compound under a potential gradient. EXPERIMENTAL The electrolytic cell for these experiments was a modified, three-neck, round-bottom, 500-ml distillation flask. Sealed into the side of the flask was a Luggin probe which monitored the surface of the working electrode and extended out of the flask to a small reservoir containing a saturated calomel electrode. The counter electrode was platinum. The three electrodes were connected to a Wenking po-tentiostat which maintained a preselected constant potential near the surface of the working electrode with reference to a saturated calomel electrode. All potentials noted in this paper are with reference to a saturated calomel electrode at 45° ± 5°C. The potential and the current were both monitored using Sargent Model MR recorders. The antimony electrodes were cast in graphite molds to form spheres about 15 mm in diameter with a shank 6 mm in diameter and 10 mm long. A heavy copper wire (12B & S gage) was soldered to this shank. Collodion was applied for protection to the shank and the connecting part of the copper lead. A snug-fitting O-ring was slipped over the shank and the electrode was then fitted into a teflon holder such that only the spherical portion was exposed. The electrode surfaces were cleaned and chemically polished prior to assembly and introduction into the electrolyte by etching in a modified CP-4 solution (50 parts glacial acetic acid, 10 parts concentrated nitric acid, 2 parts 48 pct hydrofluoric acid). The electrolyte was 10-2 M In+3 in 1 MH2So4 and its temperature was held constant by refluxing. The reflux condenser was open to the atmosphere and no temperature correction was made for changes in barometric pressure. The indium concentration in the electrolyte was checked from time to time by the analytical method outlined below for the determination of the amount of indium antimonide formed electrochemically. A schematic of the recorded potential is shown in Fig. 1. At point A the antimony electrode was introduced into the cell and the open-circuit potential recorded. At point B the potentiostat, preset at the desired potential, was switched on. It was switched off at point C and the potential fell to the open-circuit value of the electrodeposited indium. The

Jan 1, 1965

By J. G. Giddings, R. Kobayashi

Residual viscosity, the ViSCOSitY at a given pressure and temperature minus the dilute gas viscosity at the same temperature, has been found to be independent of temperature for pure components and mixtures for simple molecules and light hydrocarbons. The residual viscosities for methane, ethane, propane and four mixtures were correlated as a function of reduced density and molecular weight. INTRODUCTION Earlier efforts in correlating the viscosity of light hydrocarbons and associated gases under pressure, primarily by some form of the corresponding states principle, have been reported elsewhere.7 The formal theory of corresponding states principle for viscosity from non-equilibrium statistical mechanical arguments for simple molecules has been developed by Helfand and Rice.13 The most serious obstacle to the development of a generalized corresponding states representation of viscosity data, even for simple molecules, has been the limited quantity of precise viscosity data of pure components and mixtures over a wide range of pressure and temperature conditions. Viscosity data on light hydrocarbons have recently been contributed by several laboratories.2,6,8,23,25,26 In the study of the viscosity of nitrogen, Michels and Gibson" observed that the viscosities of nitrogen as a function of density gave parallel isotherms. The same behavior has since been reported for other gases.".= The observed behavior indicates that the residual viscosity or the viscosity at a given pressure and temperature minus the dilute gas viscosity at the same temperature is a unique function of the density. Abas-Zade,1 Michels and Botzen,18 and Michels, Bot-Zen, Friedman and Sengers,19 observed similar behavior for thermal conductivity, the residual thermal conductivity being defined in a manner parallel to that of residual viscosity. Thodos and co-workers 4,15,24 applied the residual viscosity concept to the viscosity of pure monatomic and diatomic gases. Ellington and co-workers10,25 made the residual viscosity vs density plots for ethane and propane, but omitted the region below a residual viscosity of 15 micropoise and showed a systematic separation of the ethane isotherms in the low density region. Eakin correlated the residual viscosity of methane, ethane, propane and n-butane empirically as a function of density and molecular weight: Carmichael and Sage6 recently presented ethane residual viscosity vs density values in the gaseous liquid, and near critical regions as a single univariant function of density. Flynn, Hanks, Lemaire and ROSS" have contributed extremely accurate viscosity data to confirm that the residual viscosity concept is essentially correct, but may not be accurate within 0.1 per cent of the viscosity value for the gaseous state- The recent studies by Giddings12 indicate that the residual viscosity of methane, propane and each of four methane-propane mixtures are unique functions of density Over the temperature and the density ranges studied.

Jan 1, 1965

By William D. Klopp

A study was conducted of the tensile and creep properties of are-melted and electron-beam-melted tungsten over the temperature range 2250° to 4140°F. The tensile and creep strengths vary with pain size, the finer -grained materials being stronger. The activation energy for transient creep at 2250° to 3500°F is 95,000 cal per (g)(mole), while that for steady creep at 3300o to 4000°F is 141,000 cal per (g)(mole). At 2875o to 3300°F the apparent activation energy for steady creep decreased with decreasing temperature. It is suggested that cross slip is rate controlling during transient creep, while dislocation climb is rate controlling during steady creep above 3300° F. ALTHOUGH considerable data have been generated on the high-temperature tensile properties of powder-metallurgy tungsten,1 relative few data have been published on the properties of are-melted2 or electron-beam melted tungsten.3 Furthermore, the available data show a fairly large amount of scatter at high temperatures. The effects of structure and purity have not yet been defined, aside from observations that high-purity electron-beam (EB)-melted tungsten3 and single-crystal-plasma-flame tungsten4 are weaker than less pure powder-metallurgy tungsten. The creep behavior of powder-metallurgy tungsten has been studied, but no data are available on the creep behavior of tungsten consolidated by melting. Green5 found that powder-metallurgy tungsten exhibited linear creep at 4082° to 5072°F with an activation energy of 160,000 cal per (g) (mole). The similarity of this activation energy to that of 153,000 cal per (g)(mole) for volume self-diffusion6 suggests that recovery of strain hardening by dislocation climb is rate controlling in this temperature range. In studies at 4800°F, Sutherland and Klopp7 concluded that grain size significantly affected the creep behavior of commercial powder-metallurgy materials. This grain-size effect was suggested by sherby,8 although the opposite relation had been reported for aluminum.' The purpose of the present study was twofold: first, to provide baseline data on high-temperature tensile and creep properties of are-melted and EB-melted tungsten for concurrent tungsten alloy studies, and, second, to determine the phenomenolo-gical effects of structural and purity variables on the high - temperature mechanical properties of tungsten. EXPERIMENTAL The are-melted tungsten materials were prepared by melting sintered 1-1/4-in.-diam electrodes into 2-1/2-in.-diam by 5-in.-long ingots. The are-melting facility has been described previously.' Eight ingots were melted, machined, and hot-extruded at

Jan 1, 1965

By R. R. Kimpel, L. G. Austin

An equation is derived describing fragment size for single fracture of brittle solids. It contains the equations of earlier workers as special or approximate cases and, in addition, is capable of describing coarse distributions in which a few large particles are produced on fracture. The equation can be fitted well to single fracture experiments where over-breakage is avoided. In 1956 Broadbent and callcottl described a method of analyzing the unit operation of grinding, applicable to homogeneous breakage of brittle materials. In essence, the grinding process was split into two parts: 1) the fractional amount of a given size which is selected for grinding per unit time, 2) the size-weight distribution of the fragments produced by breakage of this certain size (primary breakage distribution function). The theory was formulated using matrix algebra. They attempted an experimental verification of the theory using an assumed primary breakage distribution but the results were not very satisfactory. Austin and Gardner2 showed that this assumed distribution was widely different from experimental values and that it led to the poor agreement of predicted size-weight distributions with experiment found by Broadbent and Callcott. In addition, Austin and Gardner2,3,4 reformulated the original approach in terms of differential equations of grinding and demonstrated that the approach led to a very satisfactory description of the grinding process, providing that the descriptive parameters were measured experimentally. Recent work5 has substantiated these findings and the distribution functions of several materials ground under different conditions in different mills have been determined experimentally. The fraction underweight versus size used by

Jan 1, 1965

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper' that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,' was not adequate for this study.

Jan 1, 1965

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of' (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.'-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "'12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger's terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By S. J. M. van Leeuwen, R. Feenstra

The effect of jets on bit penetration has been investigated by means of a 50-ton drilling machine and 8½-in. commercial jet bits, drilling under representative bottom-hole conditions. The conclusions apply to the drilling of impermeable rock only. Penetration rate is in all cases primarily hampered by a differential pressure effect, known as dynamic hold-down. Jet action can reduce this slightly. Major gain in penetration rate, up to 25 or 50 per cent, is already ohtained at medium-high jet power. At high bit load, penetration by soft to medium-hard-formation bits is further hampered by bit-balling. Its alleviation requires intensive tooth scavenging, which is best performed by slanted nozzles with trailing, high-velocity, high-volume jets, hitting bottom in front of the teeth. Penetration may then improve by a 100 per cent. At high bit load, bottom-balling limits the penetration of insert-type bits. In this case bottom scavenging is required, which is most effectively performed with high velocity jets from nozzles extended close to bottom. As a result of this measure, penetration may improve 70 per cent in non-friable rock, and less in friable rock. This will make the insert-type bit more versatile. Toothed hard-formation hits suffer at high bit load from both bit- and bottom-balling. Slanted nozzles, possibly much extended, with high-velocity, high-volume jets then have best prospects. INTRODUCTION For years the use of jet bits in oil well drilling has been increasing, in conjunction with ever greater hydraulic horsepower. To the same extent, the need for efficient use of the horsepower has grown.' This paper, it is hoped, will contribute to an understanding of how effective jet action may be obtained. It deals with the effect of jets on phenomena that are known' " to hamper bit penetration. To study this effect, laboratory drilling tests were performed with 8½-in. commercial bits under bottom-hole pressures representative of deep wells. The investigation has been restricted to the drilling of practically impermeable rock. In the following sections, the increase in bit penetration rates due to jetting is discussed for conditions which made the troublesome phenomena stand out one at a time. A brief definition and interpretation of these phenomena is given in Appendix A. Appendix B gives the results of measurements of fluid velocities along the hole bottom, performed in stationary flow tests. Descriptions of equipment, bits, rocks and mud are collected in Appendix C. Unless otherwise mentioned, drilling conditions were kept standard as given in Table 1. CUTTING TRANSPORT TO THE ANNULUS Jet action was for some time believed to merely improve the transport of cuttings from bottom to annulus, resulting in a clean hole bottom. Flow tests performed in 1954 at the Battelle Memorial Institute6 showed, however, that jet velocities of the order of 40 ft/sec sufficed to clear even large (0.4-in.) chips from bottom in the time between two successive tooth actions. In the field, optimum jet velocities are appreciably higher, indicating that other effects must be involved. This much is confirmed by the results of our drilling experiments in soft rocks performed under atmospheric pressure, i.e., in absence of pressure-differential effects. Fig. 1 shows that variation in the nozzle velocity from 40 to 330 ft/sec had no effect on penetration rate, unless the bit penetrated more than 7 mm per revolution, which is about half the tooth height. At such high rates—150 ft/hr at 100 rpm—cuttings would be caught in the tooth cavities, leading to bit-balling, which was noticed on inspection of the bit. The jets thus assisted in keeping the tooth cavities clean. This is just perceptibly reflected in the penetration-rate curves of Fig. 1: Much the same results were obtained in hard rocks with hard-formation three-cone bits. The conclusion is that transport of loose cuttings towards the annulus does not require a powerful jet action. In the following sections we shall see that in deep-well drilling other phenomena are of greater importance. DYNAMIC HOLD-DOWN It is generally accepted that, in deep-well drilling, bit penetration is hampered primarily by the existence of a difference in pressure between the fluid in the hole and that in the rock at the depth of cutting.2-5 In the drilling

Jan 1, 1965

By M. C. Flemings, A. A. Tzavaras

Analytical and experimental procedures are descrihed for quantitative determination of volume-fraction microporosity in metals by mimorarlio-graphg. The analysis assumes spherical pores but allows for the observed fact that pores or portions of pores smaller than a given thickness do not project an image on the film. Volume-fraction microporosity was measuured in cast low-alloy steel and shown to vary from 0.6 x 10-4 to 10 x 10 depending on mode of solidification and on whether the material was air- or vacuum-cast. The aim of work described herein was to develop a method of quantitative measurement of the volume fraction of microporosity in cast metals. Microporosity, present in nearly all castings and ingots, is always interdendritic in nature and may be large enough to be seen on a polished surface with the naked eye. More generally, it is smaller in size, and its detection more difficult. Three techniques might be considered for measurement of microporosity: 1) lineal analysis of a polished metallographic surface, 2) density measurement, or 3) quantitative microradiography. As will be shown later, volume fractions of porosity in directionally solidified castings may be the order of 10-4 to 10-3; such small amounts of porosity are difficult to identify and measure on a polished surface. Density measurement is also not a suitable technique (for alloys) when the volume fraction of porosity is low. This is because the density of the base metal is often not known within the necessary accuracy, due to microsegregation or partial phase transformations. In general, it is not possible to completely eliminate microsegregation without also altering the porosity. Because of the limitations of the foregoing techniques, quantitative microradiography was employed to determine amount of porosity. In recent work, microradiography has been found to be useful for qualitative measurement of porosity, including determination of size and shape of individual pores;&apos;)&apos; however, quantitative determination of amount of porosity has not been attempted. I) CALCULATION OF VOLUME-FRACTION POROSITY The following analysis employs procedures similar to those of Cahn and Nutting3 and Hilliard.4 Major simplifications are that pores are assumed to be spherical and to be present in sufficiently small quantities that no overlapping occurs. A basic difference from the previous treatments is that the limited "sensitivity" of microradiography is considered. Assume first 1) cavities are spherical and of uniform diameter, 2) cavities are randomly distributed, 3) volume-fraction porosity and specimen thickness to pore radius ratio are sufficiently small that overlapping of the projected images of cavities is negligible, 4) sensitivity is limited (i.e., holes or portions of holes of less than a given thickness do not project an image on the film). The sensitivity, is defined as: where 5 = minimum thickness of void from which an image will be projected on the film and t = specimen thickness. Now, from Fig. 1, it is possible to distinguish between two different types of holes. These are 1) holes whose centers lie within the region t/2 > X > 6/2, where X is distance from one surface of the specimen (positive into the specimen), and 2) holes whose centers lie within the region (6 — r) < X < 6/2, Holes whose centers lie outside X = (6 -r) project no image on the film. These two types of pores are considered separately below. Type 1 Pores. When 6 is greater than 0, the image of a spherical cavity of radius r appears on the film as a circle of radius a which is smaller than r. From geometry, Fig. 1: a2=r2-52/4 [2] where a = radius of image of pore on film and r = radius of pore. Since the pores are randomly distributed and spherical V =4/3pr2Nv [3] where V = volume fraction of voids and Nv = number of pores per unit volume and the number of images of Type 1 pores per unit area of film, N&apos;A, is

Jan 1, 1965

By B. F. Oliver, F. Garofalo

Gas-metal heterogeneous reactions and zone-lrelting were sinultarneously employed to produce several high-purity irons with low interstitial contents in a levitating- zone melter. Successive zone-tneltitzg pusses were made in carious sequences of atmospheves which included prepuvified tank hy-drogeta, water vapor hydrogen, palladiuril-purified hydrogen, and vacuunm of 2 x 10-6 Torr. Different irons ranging in purity from 99.89 to 99.996 pct with residual curbon contents of 17, 8 to 10, and 3 to 5 ppm have been Drepared. No measuvable gradient in the residual carbon content was observed along the entire zone-melted length (6-10 in.) in I-ilz.-diameter bars. The absence of a carbon-concentration gradient in the solid indicates an apparent distvihution coefficient of 1, an unusual condition. Internal friction, solid-state extraction, and hot-hardness results indicate that the level of mobile carbon in a iron depends on the gas-metal heterogeneous reactions employed. Purification under an oxidizing atmosphere resulted in the immobilization of nearly all of the carbon present at leuels of 10 ppm or less. Continuation of purification in a reducing atmosphere veturued the carbon to a state of mobility which was aguin reversed by further purification in all oxidizing atmosphere. The immobilization of curbon at "vesidual levels " is believed to be associated with a strong interaction between carbon and oxygen atoms. frons with low carbon and nitrogen contetzts which did not exhibit a hot-hardness peak were produced after zone ynelting in vacuum. CARBON, nitrogen, and oxygen have strong and well-known effects on many properties of iron. These effects persist even at concentrations of 5 to 20 ppm. The intent of the present investigation was to establish procedures for the preparation of high-purity iron with concentrations of these elements in the range of 5 to 20 ppm and lower. The results reported here deal with the procedures employed to prepare high-purity iron, and with observations on the behavior of certain elements at "residual levels": particularly carbon. The details of the (levitating) zone melter in which the final purification steps are performed and the necessary control of the pertinent solidification variables have been described previously.1,2 MATERIALS AND PROCEDURES Commercial electrolytic iron was induction vacuum-melted and cast into 30-lb ingots. Melt additions and ingot analyses for carbon, oxygen, and nitrogen are noted in Table I. All ingots were melted in stabilized zirconia crucibles conditioned with one iron wash heat. Middle sections of the ingots were forged to 1-1/4-in. rounds, machined to 1-in.-diameter bars, then cut to 36-in. lengths. The zone-melting operations were performed on six iron bars (A to F) at a freezing velocity of 2 in. per hr with the freezing interface rotating2 at 200, 300, or 400 rpm. Liquid zones were passed through the bars in various sequences of atmospheres, Table 11, including prepurified tank H2, palladium-purified Hz, wet H2, and system vacuum of 2 x 1018 Torr. Wet-Hz atmospheres were obtained by bubbling palladium-purified Hz through water exhibiting a resistance of 3 megohms. This water was heated with a platinum-immersion heater and was degassed prior to use. Zone melting in a wet-HZ atmosphere resulted in oxidation of the elements which are oxi-dizable with respect to iron. Fine oxide particles were observed on the surface of the liquid zone, and were encased in the bar surface with the passage of the molten zone. Between each zone pass, the surface of the bar was removed by filing and deep etching; this was continued until the oxide formation ceased. The filings were magnetically separated and the residues analyzed by optical spectroscopy. These were especially high in silicon and manganese. Samples were removed from the iron bars, with few exceptions, following each zone-melting operation. A 0.08-in.-thick disc was cut with an Al2O3 cut-off wheel at a point 1/2 in. above the beginning of freezing. Material from each disc was used for hot-hardness measurements, resistivity-ratio measurements, and carbon, nitrogen, and oxygen analyses. Analyses for most other elements were

Jan 1, 1965

By R. W. Guard, M. E. Fine

By treating the dislocation like a surface and ap-plying the usual thermodynamic treatment to the adsorption process a Gibbs adsorption equation for dislocations was derived. For extended dislocations in binary solutions the adsorbed concentration on the fault, X2a, may be computed from (jo/da2b) where a2b is the activity of the solute in the bulk material and s is the stacking-fault energy. Using the data of Howie and Swann for s the adsorption concentration goes through a maximum at 2 at. pct Al in Ag-Al, 10 at. pct Zn in Cu-Zn, and 8 at. pct A1 in Cu-Al. The pinning stress calculated from this concentration difference goes Ihrough a maximum at the same concentration us the peak in X2 a. The computed pinning stress thus does not vary with composition in the manner predicted by Suzuki, as was also pointed out by Hendrickson. The results are compared with the stress increment which can be attributed to Suzuki locking in Cu-Zn and Cu-Al stress-strain curves. They both agree in magnitude and in the location of the maximum. The predicted and observed maximum values for the Cu-Zn system (where activity data are available) are 700 g per sq mm (predicted) and 1000 g per sq mm (measured, laking into account the orientation factor of 2.2 to convert poly-crystalline to single-crystal data). CERTAIN simple internal surfaces may be regarded as dislocation grids. This fact suggested that it might be profitable to consider certain phenomena related to segregation of solute atoms at dislocations from the point of view of the thermodynamics of surfaces and surface adsorption. A general treatment of this type is given and then the results are applied to Suzuki segregation and pinning. Confirmation of the results is obtained from comparison of stress-strain behavior for copper and copper-base alloys. Two kinds of dislocations need be treated: perfect and extended dislocations. In either case the line tension of a dislocation, ?. the work which must be done to increase the length of dislocation by a unit length, is analogous to the surface tension. For an undissociated dislocation ? is the self-energy of a unit length of dislocation; for an extended dislocation where is the self-energy per unit length of a pair of partials far enough apart so that there is no interaction energy, is the interaction energy per unit length, is the stacking fault energy per unit area, and w is the equilibrium separation of the paired partials. In the absence of an applied stress the force pushing the dislocation partials apart in a close-packed structure is Gb2/12p where G is the shear modulus, b is the Burgers&apos; vector of the complete dislocation, and is the separation of the partials. At the equilibrium separation, w this force equals s. Thus

Jan 1, 1965

By A. Rosen, P. Wynblatt, J. E. Dorn

The temperature, strain rate, and structure dependence of the flow stress in a poly crystalline Fe-2 pct Mn alloy was investigated between 77" and 370°K. It was possible to identify the low-temperature data from 77° to 160°K with Dorn and Rajnak&apos;s theory of the Peierls mechanism of plastic deformation. Above 160°K one or more thermally activated mechanisms must he operative; however, these were not identified in this investigation. The mechanistic basis for the rapid decrease in the flow stress of bcc metals with an increase in temperature over the low-temperature range is yet being debated. Various dislocation mechanisms have been suggested in the past but the agreement between the various proposed theories and the experimental results have not been definitive. In the present paper, the authors will demonstrate that the plastic behavior of polycrystalline iron containing 2 wt pct Mn plus interstitials agrees excellently with predictions based on the Peierls mechanism from 77" to 160°K whereas from 160" to about 370°K other as yet unidentified thermally activated mechanisms take over. Undoubtedly, the overlap of these mechanisms with the Peierls mechanism contributed to the difficulties of rationalizing the low-temperature behavior of iron and its alloys. I) EXPERIMENTAL TECHNIQUES AND RESULTS Although extensive data are now available on the effect of temperature and strain rate on the flow stress of various bcc metals and alloys, it was, nevertheless, deemed necessary for the objectives of the present study to obtain highly accurate data of the type most pertinent for checking the theories on a series of well-documented work-hardened states. Iron containing 2 wt pct Mn was used in this investigation in order to obtain a lower ductile to brittle transition temperature than that for iron.&apos; The additional elements present were 0.004 pct C, 0.05 pct 0, 0.004 pct S, 0.003 pct P, 0.006 pct N, and 0.001 pct Si. The as-received 3/8 by 3/4 in. bars were cold-rolled to 0.100-in. thickness, recrystallized under argon for 30 min at 1073"~, further cold-rolled to 0.063-in. thickness, and finally recrystallized under argon for 30 min at 1000°K. This treatment gave a stable reproducible equiaxed grain structure having an average grain diameter of about 90 p. Prior to the final recrystallization treatment, the sheet was machined into tensile specimens 1/4 in. wide having a 1.625-in.-long gage section. All specimens were tested in controlled-temperature baths on an Instron Testing Machine. For convenience in the theoretical analyses the data will be given in terms of the shear stress for flow, 7, the shear strain rate, f, and the shear strain, y. A series of three standard strain-hardened states were obtained by prestraining specimens at 300°K and at a shear strain rate of 7.68 x lo-&apos; per sec to three stress levels of 6.89 X l08, 10.3 X lo8, and 14.5 x 10&apos; dynes per sq cm, respectively. Immediately following this prestrain the temperature bath was changed and each specimen was pulled in tension at either f = 7.68 X lo-&apos; or f = 3.06 X 10"3 per sec. In terms of the accuracy that was achieved, the values obtained did not deviate more than *0.1 X 10&apos; dynes per sq cm and * 1°K from the reported values of stress and temperature and not more than *5 pct in the reported values of the strain rate. The tensile stresses were converted to shear stresses using a factor of 1/2. The shear stress for the initiation of flow at the test temperature was determined by taking a y = 6.16 x 10&apos;3 offset. from the modulus line at which point good accuracy could be achieved in determining y and the associated flow stress 7, with only a negligible increase in the pre-

Jan 1, 1965

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (&apos;&apos;segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.&apos; Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By K. R. Janowski, A. B. Chase, E. J. Stofel

Ruby crystals of exceptional optical quality have been grown from fluxes composed of Bi2O3 + PbF2 or Bi2O3 + BiF3. Careful control of growth conditions was required to minimize the number of growth defects consisting primarily of dislocations, occluded flux, and growth twins. Slow growth rates coupled with the addition of small amounts of La2O3 as a flux dopant were helpful in producing nearly perfect crystals. Chromium concentrations up to 1 pet were incorporated into these crystals without adversely affecting their perfection. Crystals up to 10 mm in diameter having as few as one to ten dislocations per crystal were typical of those produced under optimum growth conditions. Under these same conditions the occlusions were eliminated, and growth twins were either eliminated or reduced to one to three twin boundaries per crystal. INTEREST in the nature of lattice imperfections produced during the growth of ruby crystals (Al2O3-corundum structure) has been stimulated recently by the need for ruby lasers of good optical uniformity. As a result, ruby crystals grown by the flame-fusion (Verneuil) process have been studied in detail and have been found to contain high densities of dislocations (106 to 107 dislocations per sq cm) and mosaic structures that impair their optical quality.&apos;-3 Attempts to improve the quality of Verneuil-grown crystals by controlling the growth variables have not been entirely successful. On the other hand, rubies grown by the flux process have received little attention even though their more nearly equilibrium growth conditions suggest that they would have fewer growth defects. Nelson and Remeika have shown recently that small flux-grown rubies can indeed be made into very low-loss lasers. However, they did not report information on crystalline imperfections in these crystals.4 Stephens and Alford have reported briefly on defects found in a flux-grown corundum crystal but they neither described these defects in detail nor related them to the method of growth.5 The present investigation was undertaken to establish the relationship between growth conditions and crystalline perfection of flux-grown rubies, sapphires, and other crystals of the corundum family. EXPERIMENTAL PROCEDURE The corundum crystals used in this study were grown by slowly cooling solutions of A12O3 in molten-salt solvents of PbO + PbF2, Bi2O3 + PbF2 or Bi2O3 + BiF3. The materials employed were Linde A (a Al2O3 powder) with reagent-grade chemicals as solvents. Some of the solutions also contained small additions (1 pet or less) of one or more of the transition metal elements chromium, manganese, iron, and titanium as crystal dopants. La2O3 was added to some of the solutions to alter the growth habit of the crystals. The La2O3 promoted the occurrence of growth facets parallel to (0112) and {1011} planes, where the indexing system is the morphological system described in detail by Kron-berg6 and used throughout this paper. The melts from which the crystals were grown were prepared by mechanically mixing the various constituents and placing them in platinum crucibles. The covered 50- and 100-ml platinum crucibles were heated in muffle furnaces at 1250°C for short periods of time (1 to 4 hr) and then program-cooled at either 2° or 4°C per hr to 1000°C. At this lower

Jan 1, 1965