Search Documents

Key elements of open-pit design fixing the ultimate pit limits are stripping ratio, pit slope angle, and grade cutoff. Results of exploratory and development drilling should be reduced to horizontal sections corresponding to level spacing. It is advisable to interpolate the actual drillhole values to a uniformly spaced 50-ft grid system. Vertical sections can be and are used to approximate the fixing of pit limits, but horizontal sections must be used to optimize a pit design. To develop a pit design requires the establishment of the break-even stripping ratio. This ratio is applied only at the surface of the final pit and must not be confused with the over-all ratio, which is always less; otherwise there would be no profit in the operation. The break-even stripping ratio is determined by the formula: [ ]

Jan 10, 1967

The selection of a particular machine for production drilling is the most critical drill evaluation the pit engineer is called upon to make. It is a true engineering design problem requiring value judgments. Generally, the procedure follows these steps: (1) Determine and specify the conditions under which the machine will be used, including such service factors as labor, site, weather, etc. (2) State the objectives for the rock-breakage phases of the production cycle of operations--considering excavation and haulage restrictions, crushing capacity, production quota, and pit geometry-in terms of tonnage, fragmentation, throw, etc. (3) On the basis of blasting requirements, design the drill-hole pattern (hole size and depth, in- clination, burden, spacing, etc.) (4) Determine the drillability factors and select the drilling methods which appear feasible for the kind of rock anticipated. (5) Specify the operating variables for each system under study, considering drill, rod, bit and circulation fluid factors. (6) Estimate and compare performance parameters, including costs. Major cost items are bits, drill depreciation, labor, maintenance, power and fluids. (7) Select the drilling system that best satisfies all requirements with the lowest over-all cost.

Jan 10, 1967

The fundamentals of blasting involve both the properties of explosives and of the rock being blasted. Four of the most important explosive properties appear to be energy density, bulk density, rate of energy release and the pressure- time history of the gases produced. Important rock properties are density and porosity, strength, and energy absorption including the effective moduli of elasticity. Rock structure also has a marked effect on its properties: for example, joints, bedding, and fracture alteration. Several mechanisms enter into rock fragmentation by blasting. These include slabbing, radial fracturing, crushing and bursting by the gas bubble. All of these factors are closely related to properties of both explosives and rock. Slabbing depends upon the first generated stress wave, whose shape and magnitude are a result of the pressure generated by the explosive, its time history and the resultant response of the rock, including its ability to sustain the stress wave. Actual slabbing, in turn, is a function of the magnitude and shape of the pressure pulse and the tensile strength of rock. Further fragmentation depends to a great extent upon the amount of gas in the bubble and its energy and pressure.

Jan 10, 1967

Some specific observations might be appropriate concerning the reporting of Research and Development results. Each report is usually directed towards a particular group, such as technical, operational financial, or marketing. The requirements and background of the group receiving the report must be considered, and the emphasis and coverage geared to the training of people concerned. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. (A check list prepared in conjunction with the various users of the report is sometimes useful to prevent omissions.) Typical points listed might be: Financial- (1) capital requirements, (2) timing of capital expenditures, (3) tax implications, including depreciation, depletion and investment credits, (4) changes in working capital.

Jan 10, 1967

By L. C. De Jong, J. F. Shirley, M. L. Campbell

The Toquepala concentrator of the Southern Peru Copper Corp., located approximately 720 miles southeast of Lima near the Chilean border, processes 36,500 tons of ore daily containing between 0.50% and 3.00% copper. The molybdenite content in the ore also varies greatly, ranging from essentially nothing to as high as 0.15%. The 1966 yearly averages were approximately 1.20% copper and 0.03 % molybdenite. The three basic problems that plague the opera- tion of any molybdenite recovery plant are all present at Toquepala in large measures. Both the quantity of plant feed and the quantity of molybdenite contained in the plant feed are continuously changing. Even more detrimental to an efficient operation is the fact that the copper mineralization in the feed frequently changes once in every 24 hours and occasionally once a shift. From the point of view of the molybdenite plant metallurgist, there are four distinctive chalcopyrite concentrates and, at least, an equal number of chalcocite concentrates treated in the molybdenite recovery circuit. The various types of concentrates are distinguished mainly by their mineral content and how effectively the copper minerals are depressed by the different reagents used in the circuit.

Jan 9, 1967

By M. Safiuddin

Within the mining industry, open-pit mining has progressed to a point where a 200-yard walking dragline is as conceivable today as a 35-yard dragline was just a few years ago. This is possible due to the technological advances and efforts of the excavator manufacturers, and the manufacturers of electrical equipment have always stayed abreast with them in meeting their requirements and in making available their experience with the latest control techniques and hardware from various fields for application in the mining industry. An electrician in the coal mines of Pennsylvania who had not heard the word "thyristor" a few years ago now wonders how the old excavators with Rototrols® and magamps could ever work. The thyristors, transistors and operational amplifiers which were considered too fragile and delicate for a rugged and severe application like the mining industry, today constitute the brain of an excavator control taking commands from the operator and giving signals to the muscles of the excavator to move the bucket within a few seconds. A giant 200-yd bucket filled with overburden moves within seconds of the operator's command. Digging cycles for these excavators range from 40 to 60 sec depending on the swing angle. With these tremendous production capabilities of the excavators, the equipment failures and downtime become very expensive, and the loss of return on large capital investment for such machines becomes intolerable. Even though these failures and downtimes cannot be avoided completely, a good preventive maintenance program can help reduce them, thus increasing the machine availability. As we shall see below, the causes for breakdowns and failures of electrical equipment can be analyzed and a good preventive maintenance program can be drawn up to eliminate most of these failures.

Jan 9, 1967

R. S. Shoemaker: Our first question is, is there a need for a grizzly before a primary crusher? What is its effect on crusher capacity and crusher maintenance? Is it worth the extra capital cost in a crusher installation? Vincent: ASARCO has a grizzly at Mission. Utah Copper uses grizzlies ahead of their gyratories. There is some quite abrasive ore at Mission, an argillite type of rock, which has a work index of 16.5 to 20, which is getting up toward the taconite classification. We get a life of 12- 16 million tons per set of concaves or per mantle with the grizzly ahead of the crusher. At Duval Corp., some 6 miles to the south of Mission, their crusher installation on a good, hard rock does not have a grizzly, and the last information I had is they get a life of about 2 ½ -3 million tons on their mantle and concave. At Silver Bell, our other copper unit in Arizona, they do not have a grizzly ahead of the gyratory and there they get a life of about 5-6 million tons. At Utah Copper, which we all know is a fairly soft ore, relatively speaking, they get a life of 24-27 million tons with grizzlies ahead of the crushers. I think a grizzly has a very definite effect on the life of the mantle and the concaves. As far as a jaw crusher is concerned, I think that usually it is desirable to have a grizzly if it is properly designed, which means it is self- cleaning. Otherwise I would not like to see one in the circuit.

Jan 9, 1967

By August E. Vandale

Mining of the Freeport and Pittsburgh coal seams in the Pittsburgh vicinity dates back more than 100 years, and Consolidation Coal Co., or its predecessor, Pittsburgh Coal Co., has been actively mining in the area since 1900. Over the years, Consol has acquired good legal title to the coal lands purchased from individual farm owners, with broad mining rights, and in 98% or more of its title holdings, the company has a complete waiver of surface damage or the right to subside the surface land. (Titles in Pennsylvania can be in three forms: title in fee; title to the mineral; or mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage.) In the early history of Consol, individual farms overlying the seams were purchased from land owners. Many of these titles severed the coal estate from the "in fee" title, and mining rights with waiver of surface damage were conveyed in the original severance deed. In this manner, Consol was able to put together its large mineable coal reserves. Consol has practiced "full recovery" mining as far as practical from its early years of hand loading to the recent era of mechanization.

Jan 9, 1967

Sifto Salt Div. of Domtar Chemicals Ltd. has developed a new method for installing roof bolts in the high backs of its 1-million-tpy rock-salt mine at Goderich, Ontario, on the east shore of Lake Huron. The method teams a telescoping- boom hydraulic crane with a specially developed combination auger-drill and bolt-tightening ma- chine. One man, controlling all operations from a basket supported at the end of the crane's telescoping boom, installs an average of 100 5-ft roof bolts per shift, at heights to 45 ft. The mine has very long backs that are not as stable as might be expected. The result has been that roof scaling has occupied an unusually high percentage of the underground work force. About six years ago, company officials decided to go to 100% roof bolting of all backs as a safety measure. The present roof-bolting equipment is the result of a development program instituted at that time to find a faster and more economical method for doing the job.

Jan 9, 1967

By Eugene P. Pfleider, Jared Scofield

During the past ten years, the trend on the Mesabi Range has been toward the establishment of integrated operations which mine, concentrate, and pelletize the large reserves of magnetic taconite. However, since the supply of open-pit ores of acceptable quality is by no means inexhaustible, it has been proposed that it be supplemented by developing the magnetic taconites that extend down dip past the economic limits for open-pit methods. In Phase I of a long range study, Pfleider and Yardley1 collected information on the general character of the Mesabi iron formation at depth and proposed that an underground lane-and-pillar mining system be considered to extract those high grade layers where they might exist over a considerably areal extent. An approximate cost estimate was included initially, with the thought of later developing a feasibility study as time permitted.

Jan 9, 1967

Oceanographers are tooling up. Back of the build-up is Navy defense work and private business. Business is dipping toes in the ocean gingerly and not sure whether the motivation is based on logic or intuition. The problem is that new business opportunities in the oceans could explode rather than evolve. The question is when. At stake for earthlings are food supplies, mineral resources, oil and gas, weather forecasting, navigational systems, shore erosion control and sewage disposal, as primary targets. "Twenty years ago, offshore oil seemed a remote possibility for economic exploitation but today it is a reality. It became a reality largely because of the development of practical ocean seismic equipment and drilling platforms. Today the oil industry is looking at submerged-type drilling rigs. Mineral exploration in the sea is more expensive than on land now primarily because familiar land tools are being modified for sub- marine work." These were the ideas expressed by C. G. Welling of Lockheed Missiles & Space Co., at one of the many meetings that have taken place so far this year on development of marine resources. Welling's views indicate the rationale of companies that have already invested in the sea. Many companies, including those in mining, have observers who caution, "go slow." The continental shelfs and even the deep ocean floor represent to the mineral industries the age-old, enigmatic confrontation-is this the time to move? To no other industry, except Defense, are the results of correct timing so vital.

Jan 8, 1967

By Erwin Zodrow, De Verle P. Harris

The Smallwood mine, owned and operated by the Iron Ore Co. of Canada, is one of the largest ore producers in Canada, producing about 15 million tons of crude ore per year. Located in the Labrador Trough near, Labrador City, Newfoundland, the open-pit operation has ore consisting chiefly of specular-hematite, with some magnetite. The magnetite content of the ore as a mineral percentage is small, but it is of considerable importance in ore grading because of its effect upon milling. Being harder than specular-hematite, magnetite increases grinding time and milling costs. Specifically, higher grade magnetite (greater than 15%) usually occurs as fine grains in a fine grained siliceous rock matrix (also as larger octahedra in carbonate bands). This tends to increase the overall breaking strength in the crude ore; consequently, the hourly mill rate and the weight recovery decrease. At the same time, because of its relatively high iron content, the magnetite does contribute to the amount of iron in a block of ore. Were the concentration of the magnetite relatively constant, its presence would be of less consequence, for appropriate adjustments could be made in the milling operations. However, the quantity of magnetite present for any run of ore varies considerably; it is the magnetite prediction for a block of ore that constitutes the greatest problem in grading. THE PRESENT ORE GRADING METHOD Ore for the Smallwood mine is graded by a computerized block grading routine (using 50 x 50 x 45-ft blocks) that applies simple weighted (inverse-distance) averaging to ore grades. The results of the block grading program are not reliable with respect to magnetite concentration. Factors responsible for this poor estimation are (1) the structural setting of the deposit, and (2) mineralogical relationships. Neither of these general factors are given adequate consideration by present methods.

Jan 8, 1967

By V. Lessels, D. J. Buckwalter, D. H. Rose

At White Pine Copper Co.'s operation in the Upper Peninsula of Michigan, the company has been losing more than four lbs of copper in each ton of sand tailings. With an average rate of 12,000 tpd of sand going to the tailing pond daily, the company has been losing more than 14 million lbs of the red metal annually. With an eye aimed toward lessening this loss, White Pine engineers in 1959 initiated a study on techniques for recovering this "lost" copper from the sands. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leaching as practiced in the precious metals industry.

Jan 8, 1967

By D. T. King

In coal preparation plants, as in many industrial operations where raw materials are handled, nuisance, health, and equipment maintenance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are therefore essential components of the plant process equipment. The objective of a dust collector is to separate solid particles from a gas stream in which they are suspended. Various types of devices can be employed to accomplish this end. The choice of the type of collecting device for a given application depends on principles of the behavior of fine particles and on factors associated with the properties of the dust (such as particle size, density, shape) and the suspending medium (such as density, humidity, viscosity, velocity). Particles suspended in a gas stream are acted upon by a number of forces including the buoyant force and frictional resistance of the suspending medium, which tend to keep the particles in suspension, and the force of gravity which tends to impart a relative motion between the particles and the fluid. The smaller the particle the greater the tendency for it to remain in suspension and, thus, the more difficult it becomes to collect the particle, or separate it from the fluid stream. To effect separation, therefore, some external force must be applied on the dust particle. When dust particles in a gas stream are acted upon by an external force, for example, gravity, centrifugal force, or an electrostatic field, the particles will be accelerated in the direction induced by the force. Because of a relative motion between the particles and the gas stream, a frictional resistance will be set up that will limit the velocity of the particle toward the force. To effect collection of the particles, this velocity must be great enough that the particles are trapped by some collection medium before the gas can transport the particles out of the collecting equipment. The most common physical mechanisms employed by collecting devices include gravity, inertial or centrifugal force, impingement, and electrostatic fields.

Jan 8, 1967

The elite group of companies below represent the mining sector of Fortune magazine's June Directory listing the 500 U.S. industries that chalked up the largest dollar sales volume in 1966. The companies are listed according to their 1966 sales rank, which is given along with their 1965 rank for comparative purposes. All of the firms except two-Freeport Sulphur and Texas Gulf Sulphur-were in the Fortune Directory last year, and both these exceptions have been counted among the top 500 in former years. The one mining name that is missing from last year's list-Consolidation Coal-has actually jumped from number 217 to 4 by virtue of its merger with Continental Oil. As can be seen from the Industry Medians, the mining industry as a whole boosted its sales 17.8%, in 1966, making it the seventh largest gainer among the 22 industrial classifications covered in the Directory. By comparison, 1965 mining sales increased 10.2%, a gain which was surpassed by 13 other industries. In two other comparative tables, mining leads the field, topping the entire list in return on sales and in assets per employee.

Jan 8, 1967

By H. S. Ten Eyck

Fertilizer normally is spoken of as having three main components: nitrogen, phosphorus and pot- ash. Certainly, however sulfur must also be considered a basic component of fertilizers, even though in many instances it does not end up as a part of the end product. In addition, with heavier cropping and the resultant drain of plant foods from the soil, we have now reached a point where the minor elements necessary for plant growth have become a major factor in the fertilizer industry.

Jan 7, 1967

By Cornelius J. Dwyer

It is possible to hold a very optimistic view of the future of the U.S. coal industry, and there are those in the coal industry who generally choose to do so. For example, a major coal company stated recently in its annual report, "Coal's prospects appear brighter today than at any period in the past." In order to continue in this state of euphoria, it is only necessary to remind oneself of the following "facts":

Jan 7, 1967

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967

By R. P. Aikman, F. G. Miller, J. M. Podgursky

In response to the growing demand for low-sulfur coking coal for iron-making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, (i.e., +28 mesh) at almost any desired specific gravity. However, in the case of fine coal (i.e., -28 mesh) neither of the two existing processes-froth flotation and hydrocycloning-in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this article is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods.

Jan 7, 1967

By Arnold H. Kackman

At the Kaiser Cement and Gypsum plant near San Jose, Calif., one rod-ball mill has taken over the entire raw grinding function for the largest single cement operation in the West. Installed as part of a major overhaul performed on the plant by Kaiser Engineers, the new mill does the work of seven previous mills in feeding the plant's six kilns and keeping pace with its annual capacity of 8.5 million bbl of cement. Installation of the mill, which is the largest in the world, was started in December of 1966 and completed in April of 1967. The over-all modernization program surrounding the new mill has included the modification of existing crushing facilities; the building of new raw materials handling and blending facilities, new raw milling facilities, and new slurry handling facilities; and the installation of a digital-analog control system.

Jan 7, 1967