Search Documents

By OÆBrien R. T

A small static bed was used to study the thermal cycles required for the heat hardening of pellets based on synthetic magnetite concentrates and a naturally fine hematite. This apparatus can be employed to yield broad process data for the design of a recuperative strand system operating on the magnetite concentrates.Various alternatives are given for a process to heat harden the hematite ore but a preference is given to the production of a self fluxing pellet. Bond types and general mineralogical structures are interpreted against the optimum firing cycle necessary to produce a defined quality of pellet.INTRODUCTIONThe work reported in this paper extends that on the "Heat Hardening of Artificial Magnetite Pellets", which was described at the International Symposium on Agglomeration, sponsored by the American Institute of Mining, Metallurgical and Petroleum Engineers at Philadelphia, U.S.A. in April 1961. Whereas that work was of a more basic nature, serving to illustrate the suitability of artificial magnetites with various admixtures, to the application of heat hardened pellets, on this occasion the aim is to illustrate the procedures which were used to establish the dimensions of commercial recuperative strands for Australian raw materials.The nature of the pellet feed, Le. relatively uniform spheres of + i in.-Yi6 in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas flows...

Jan 1, 1963

By B. Ndlovu

The world mineral industry has over the years experienced growth in the production of nickel (Ni) due to its use not only in the catalytic industry but mainly also to its demand in the stainless steel production industry. Hence there is a need to produce more pure and marketable grades of Ni through the use of efficient purification routes such as solvent extraction. The V10-LIX®84-IC system resulted in nickel (Ni) extraction isotherm shifting to lower pH levels. The pH window of opportunity for the extraction of Ni subsequently increased in solution containing magnesium (Mg) and calcium (Ca) even though the system also resulted in slight shifts to less positive pH values for Mg and Ca curves. Results showed a synergistic effect of LIX®84-IC when added to V10 for all elements, Ni, Mg and Ca. The pH50 values for elements Ni, Mg and Ca in the V10-LIX®84-IC system were 2.95, 8.10 and 7.70 respectively. Comparing results obtained when using V10 alone produced ?pH50 for Ni, Mg and Ca being 3.35, 0.15 and 0.70 respectively, which was a confirmation of the synergistic shifts for all the elements. The ?pH50 (Mg-Ni)value was 1.95 with no synergism and 5.15 with synergism and that for ?pH50 (Ca-Ni)was 2.10 with no synergism and 4.75 with synergism. This showed that the Ni-Mg separation factor was relatively larger than the Ni-Ca. Improved loading and stripping kinetics were also observed. Keywords: Nickel solvent extraction separation, magnesium, calcium, versatic 10 acid and LIX®84-IC.

Jan 1, 2008

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937

By Chengxian Lui

Detailed mineralogical and metallurgical investigations were carried out on a phosphorous-bearing manganese carbonate ore from the Huayuan manganese mine, Hunan, China. Microprobe analyses indicate that the Manganese occurs mainly in calc-rhodochrosite and in rhodochrosite. The cOll'pOsitional range of these manganese carbonate minerals is 50 -80 % MnOJ3, 0 -35 % CaOJ3, 5-35 % MgC03 and 0 -15 F~. The manganese carbonate minerals are very fine grained, IOOSt are between 4.6 and 9.4 1m in diameter. The small grains are clustered into aggregates that form bands 0.5 to 10 rnn wide. The phosphorous-bearing mineral in the ore is fluorapatite and is in grains that are generally smaller than 6 1m in diameter. Metallurgical tests show that it is possible to concentrate the aggregates of manganese carbonate minerals by high intensity magnetic separation, and to reduce the phosphorous content by rpasting the concentrate to convert the manganese carl::x>nates to insoluble hausmannite, and then leaching the roast product with HCI to dissolve the fluorapatite.

Jan 1, 1989

By J Seccatore, G Sadao, M Cardu, G De Tomi, L Finoti, F Galvão, J Romero Huerta, A Rezende, J Bettencourt

In the mining industry, rock blasting can be considered as the first phase of comminution. The downstream phases of comminution are mechanical, and consist in consecutive stages of crushing and milling for grain size reduction. The total energy of mechanical comminution depends on grain size and on the resistance of the material to grindability. Usually, the first is quantified by the grain size distribution or one of its KPIs (such as the diameters X50 or X80), while the latter by the working index (WI), representing the amount of energy necessary to reduce the size of grains of a determined amount of material to the desired equivalent diameter (usually expressed in kilowatt hours per tonne – kWh/t). It is widely recognised that it is possible to manage the output of a blast in terms of grain size distribution varying specific charge (powder factor – PF) and charge distribution; specific algorithms such as the KUZ-RAM or the SWEBREC have been created to predict such output. It has also been demonstrated how higher PFs weaken the blasted material by creating micro-fractures that reduce its WI. This paper focuses on a related aspect: the influence of charge distribution on the specific comminution energy in crushing and milling. Small-scale blasts have been performed on 14 marble blocks with different PFs and charge distribution. For every PF, charges have been designed to simulate concentrated and distributed geometries. Concentrated charges simulate opencast blasts with large-diameter holes, with large burdens and spacings. Distributed charges simulate bench blasts with small-diameter holes and reduced burden and spacing. Three control blocks have been fragmented by mechanical means for comparison. For every sample the grain size distribution and the WI in ball mill has been determined. Results show the correlations between charge distributions and the specific energy of mechanical comminution in milling. Finally, the opportunity of adjusting charge diameters and distributions in opencast blasts to improve the output of the comminution circuits is discussed.CITATION:Seccatore, J, Romero Huerta, J, Sadao, G, Cardu, M, Galvão, F, Finoti, L, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The influence of charge distribution on the grindability of the blasted material, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 749–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By J. H. Potgieter

This paper describes an investigation to separate and selectively recover silver, gold and platinum from jewellery and laboratory wastes, and produce technical grade material suitable for training purposes. Nitric acid was employed to dissolve and separate silver and other impurities from gold and platinum, which were then dissolved in aqua regia and precipitated selectively. The current work quantified the effects of temperature, stirring rate, leaching agent concentration and solid: liquid ratio on the recovery of the various noble metals and in summary yielded the optimum treatment conditions in each case. It was found that increased leaching reagent concentration (in the case of Ag), temperatures and stirring rates enhanced the recovery kinetics and optimum yield of the three noble metals. An increased liquid to solid ratio also enhanced the recovery of the silver. Recovery yields 97.1%, 99.9%and 99.4% for silver, gold and platinum, respectively, were obtained. The recovered silver, gold and platinum had purities of, respectively, 98.3%, 99.1% and 99.0%. A cost saving of approximately R10 000 per kilogram of scrap refined could be achieved by the in-house treatment of the waste, not to mention the time-saving benefit.

Jan 1, 2004

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By Barton G. Stone

"Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole," (Baxter and Parks, 1939)."An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence, the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence."The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling."Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive." (McKinstry, et al., 1948).In an actual orebody, the accuracy of sampling depends not only on the number of samples but also on their proper distribution throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore, it is important to select the places in such a way that all parts of the orebody will be represented."

Jan 1, 2014

Mr J. Meintjes (Chairman) was in the chair. There were also present: 7 Members: Messrs B. D. McNeice, A. Bain, G. E. Carlyon, C. H. Coxon, B. F. v. d. Merwe, A. C. Hofmeyer, H. J. R. Way. 4 Associate Members: Messrs E. J. Jackson, A. C. Melvill, W. Weber, R. E. Powell. 2 Visitors. It was decided to have the visit to ETC at Barberton on 20th March. A programme will be sent to all members who indicated that they wish to go on this visit. A talk on "Billet Casting of Ferrochrome" was given by Mr. B. F. van der Merwe. After question time the chairman thanked the speaker and asked for the talk to be forwarded for possible publication in the Journal. The meeting closed at 9.10 p.m.

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By Robert Hopler

DESCENT INTO A COAL MINE From “The Playbook of Metals, including Personal Narratives of Visits to Coal, Lead, Copper, and Tin Mines,” by John Henry Pepper. Published by Routledge, Wa rne, and Routledge, London, 1862 ENGINEERING NEWS New Yor k January 22, 1903 THE BEGINNING OF THE END OF DYNAMITE. In another part of this issue we have reported the results of some test results made upon one of the safety powders. It will pay every c o n t r a c t o r, miner, or user of explosives in any form to carefully re a d the article re f e r red to. Dynamite has done a gre a t work in the service of man, as did black powder before it; but its i n h e rent dangers are admitted by all and are proved by the long list of deaths and injuries, and destruction to property which annually occur through its use. Why should we continue to use an explosive that annually kills and maims hund reds of men, when others are available which are equally powerful, no more expensive and far less liable to accidental discharg e ? Dynamite when first manufacture d is pure and comparatively safe; but most unfortunately it does not always stay pure; it “rots,” and then it is exceedingly dangerous. More than this, the explosive part of dynamite is a liquid, nitro - g l y c e rine, which is absorbed or soaked up by sawdust, wood pulp or the like. So long as this liquid nitro - glycerine remains pure and remains “soaked up,” or absorbed t h e re is little danger. It has been found, however, that the nitro - g l y cerine leaks under certain conditions. During thawing it fre q u e n t l y leaks out of the stick, or if it becomes wet the water causes the n i t ro-glycerine to leak out. In either case free liquid nitro - g l y c e r i n e escapes, and in that free state it may be exploded by any very slight shock. Nor is this all, if a stick of frozen dynamite be bro k e n a c ross it has been found by tests that the frozen nitro - g l y c e r i n e w h e re thus broken is very sensitive to shocks afterward .

Jan 1, 2004

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By L. J. Froisland

The U.S. Bureau of Reclamation requested U.S. Bureau of Mines (USBM) assistance in developing design data for moving lead-zinc-gold tailings from their current location without disrupting the existing chemically stable conditions. This report presents results of USBM work in determining (1) the minimum required time to air dry the tailings to approximately 20 pet moisture under various drying conditions both in the laboratory and in the field, (2) the degree of oxidation or reduction that occurs during drying, (3) the effect of lime or cement addition before drying, and (4) the likely equilibrium conditions of the dried tailings after deposition at the new location. The limited number of tests performed by the USBM in the available time frame established trends in oxidation levels but did not provide absolute statistical validity of data values. All data from drying and oxidation testing are included in appendices to this report.

Jan 1, 2010

By Bujtor G. J, McMahon D. W

This guide to the understanding of ore reserve estimation is the revised version of a report with a similar title circulated within the CRA Limited (CRA) group of companies in mid-1980. It is the principal result to date of an Ore Reserve Study commissioned by CRA in late 1977.This guide to the understanding of ore reserve estimationis the revised version of a report with a similar titlecirculated within the CRA Limited (CRA) group ofcompanies in mid-1980. It is the principal result to dateof an Ore Reserve Study commissioned by CRA in late1977.The study was prompted by two ore reserve situations.The Zinc Corporation and New Broken Hill Consolidated,Broken Hill, had reached the point of havingto find a replacement 'for their traditional ore reserveprocedure and Mary Kathleen had to admit publicly thatore reserve predictions would not be realized. Thesewere not however the only problems to be looked at. Asmentioned more fully later, other ore reserve situationswere known, or were met during the study, in copper,gold and nickel as well, where poor realization: expectationratios had ranged from embarrassing to disastrous.These made it clear that ore reserve estimation had to belooked at afresh.The fresh look has resulted in a broadening of theconcept of ore reserve estimation from its traditionalpurely computational basis to an approach embracingall the many things that can affect expectation andrealization as essential factors. Hence this guiderepresents a gathering together of what has been learnedand what should be known to all those concerned withore reserves in any of its diverse aspects.The study has been marked"by a number of changesof thinking. At first the aspects that appeared to requireattention were two; recognition that an ore reserve statementwas an estimate, not a precise calculation; and asearch for im improved estimation procedure adapted tolow grade ores with narrow economic margins. Threeyears later the view was that the need was to incorporateinto ore reserve estimation all relevant aspects of theproposed mining operation from choice of a samplingmethod to sales contract specifications.This study is thought to be unique in being frankabout weaknesses in ore reserve estimation and intreating failures not as natural disasters (like drought orflood, which have to be endured) but as potentiallyavoidable. It has led to three principal conclusions.

Jan 1, 1982

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994