Search Documents

By Florian Kongoli

New operating conditions and process parameters are often necessary in today's industrial practice of non-ferrous smelting and converting in order to accommodate various new chemical compositions of mineral charges and environmental requirements or to conceive new and more efficient industrial technologies. An important parameter in non-ferrous smelting and converting is the liquidus surface of multicomponent slags. This surface is affected by multiple factors such as temperature, gaseous potentials, the content of each component in the slag, etc., and cannot be quantified by the existing ternary liquidus diagrams. In this work a new type of representation of the liquidus surface of multi component systems has been presented by means of a thermodynamic model. This representation waives the need of the multidimensional representation of multi component systems and yields practical two-dimensional diagrams, which can be easily used in the industrial practice.

Jan 1, 2000

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By Atsushi Shibayama

The aim of this research was to develop a copper recovery process from mine tailings (0.34%Cu) using flotation followed by high-pressure oxidative leaching (HPOL) and solvent extraction. The results of HPOL using the concentrate of mine tailings obtained by flotation under the optimal conditions of the previous study shown that an efficient copper dissolution of 94.4% was achieved in an H2O media, while the copper concentration of PLS reached to be 2.9 g/L. The solvent extraction of PLS obtained from the optimal HPOL showed that 91.3% copper was recovered in stripped solution under the determined optimum conditions, in which the copper concentration achieved to be 44.8 g/L. Finally, a proposed copper recovery process from the concentrate of mine tailings was developed by combination of HPOL and solvent extraction, while a total copper recovery of 86% was achieved.

By Teixeira

An experimental investigation on the kinetics of oxidation of As(III) with H202 in synthetic effluent solutions followed by precipitation of Fe/As (V) compounds was carried out. The variables investigated were: As concentration (200 -3000 mg/l) , oxidation pH (2.0 -11.0), oxidation temperature (25 -800C) , H202 stoichiometric excess (50% -100%), precipitation pH (5.0 -7.0), precipitation agent (Fe2+ -Fe3+). Fixed conditions were, Fe/As molar ratio (6:1) and stirring speed (560 rpm). The results were empirically modelled. The precipitates obtained were amorphous. The precipitates were checked upon their environmental stability according to the United States Environmental Protection Agency (U.S.E.P.A.) Toxicity Test, and were considered to be adequate for deposition in impermeable waste dumps. The combined Fe/H202 detoxification process, in selected conditions, was able to reduce the As contents of effluents containing 1600 mg/l As to 0.1 mg/l, in about 2 1/2 hours of total processing time.

Jan 1, 1990

By Kosei Morita, Osamu Nakano, Katsuhiko Nagai, Kazuhiro Mori

"The Sumitomo Toyo Smelter and Refinery commenced its operation in 1971 with three Peirce- Smith (PS) converters. “2 hot – 1 blowing” operation was practiced, that is one of two available converters was blowing and the other was standby in a hot state while the third converter was under repair. After several improvements, the stack time ratio reached around 90%; and processing 5 batches a day became possible.As a result of the expansion program of the Toyo smelter and refinery that started in 2001, the converter operation pattern was shifted from “2 hot – 1 blowing” to “2 hot – 2 blowing” with the installation of second converter blowers and an additional ladle crane.In 2005 a, the fourth converter was installed and “3 hot – 2 blowing” operation began. Also, with improvements experienced in the anode furnaces and the anode-casting wheel operation, today, the number of cycles has been increased up to more than 8.5 a day.The treatment techniques of fugitive gas containing sulfur dioxide from converter furnaces have been gradually reinforced, and the fixation rate of treated sulfur is currently being maintained at more than 99.9%. This paper introduces the operations described above, and the improvements in environmental management techniques for the Toyo PS converter operation."

Jan 1, 2009

By Seetharama C. Deevi, Mohammad R. Hajaligol, Sarojini Deevi

"Carbides and nitrides of iron are being considered as magnetic materials for high-density recording due to their chemical stability and high-saturation magnetization values (> 100 emu/g). Iron carbides and iron nitrides with magnetic properties suitable for magnetic media were synthesized by employing a novel synthesis procedure based on fluidization of powders in reactive atmospheres. Fluidized-bed reactors of laboratory, bench, and pilot scale were employed for the synthesis of iron carbide, FeSC2, by reducing and carburizing U-Fe203 in the temperature range of 300 to 550 ºC. A temperature of 400· ºC and a reaction time of 2 to 3 h are found to be optimal for the synthesis of iron carbide. When the carburization was carried out in a reducing and carburizing atmosphere such as carbon monoxide, nucleation and growth of FeSC2 occurred directly from Fe304 with no intermediate phases such as FeO or Fe. Longer carburization times resulted in the deposition of carbon on the surfaces of FeSC2 particles due to Boudouard reaction, and higher temperatures favored the formation of a mixture of carbides such as FesC2 and Fe3C. Iron nitrides were synthesized by reducing u-Fe203 in the temperature range of 350 to 550 ºC, followed by nitriding in the temperature range of 350 to 550·ºC. The powders were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analyzer, and a vibrating sample magnetometer.IntroductionRecent demand for high-quality recording of optical, electrical, and audio signals generated interest in magnetic tapes with high-recording densities as compared to the conventional magnetic tapes based on U-Fe203. At present, commercially available magnetic tapes contain maghematite, U-Fe203, as a magnetic material with a saturation magnetization of90 emu/g and a coercive force of 400 Oe. Recording of signals at a higher density per unit volume of magnetic material demands magnetic materials with high-saturation magnetization and a reasonable coercive force. Although metallic iron particles possess a saturation magnetization of 130 to 150 emu/g and a high coercive force of 1000 Oe, the gradual oxidation of iron-to-iron oxides (of lower saturation magnetization) prevents the use of iron particles for high-density recording. In contrast, iron carbides such as FesC2, Fe7C3 and iron nitrides such as Fe4N and Fe3N possess excellent magnetic properties coupled with good electrical conductivities and high hardness. The carbides and nitrides of iron have generated significant interest as magnetic materials for the next generation of magnetic tapes due to their unique magnetic properties and relatively greater oxidation resistance as compared to metallic iron particles [1-4]."

Jan 1, 1994

By C. Allen

A series of zinc chloride electrowinning tests was carried out in a laboratory scale cell to evaluate the effect of temperature, current density, electrolyte composition, gas sparging and additives on the performance of the cell with respect to current efficiency, voltage, specific energy consumption and deposit morphology. The anode material was DSA for chlorine evolution and the cathode was made of aluminum. At 400 A/m2 current density, a current efficiency of 90.9%, a voltage of 3.4 V and an energy consumption of 2.78 kWh/kg were observed. Air sparging was found beneficial but was not pursued for health and safety reasons. Various additives in the same chemical family as tetrabutyl ammonium chloride (TBAC1) were tested. Both TBAC1 and tetrabutyl ammonium bromide were found to be equally effective. Attempts to carry out the electrolysis at 1200 A/m2 were not as successful.

Jan 1, 2000

By Zhao-feng Xie

A new process of recycling valuable metals containing in the slag of jamesonite smelting in the blast furnace was studied. In this process, the valuable metals such as Pb, Sb, Zn and In etc. were fumed and volatilized and enriched in the dust firstly and then the dust was leached by sulfuric acid. In the leaching procedure, Zn and In in the dust entered into the leaching solution and were separated from Pb and Sb which remained in the residue.The optimal operation conditions of the fuming procedure are as follows: the mass ratio of the blast furnace slag, coal powder and lime are 100:22:10 respectively and the fuming time are 1.5~2.5 h, the fuming temperature is not below 1200C and the volatilization rates of Pb, Sb, Zn and In are 95%, 92%, 86% and 75% respectively. The optimal conditions for the leaching procedure are also presented: the consumption of sulfuric acid is 1.15 times of the theoretical consumption, the ratio of liquid to solid is 4:1 and the leaching temperature, leaching -1time and stirring speed are 90, 1.5h and 300 r?min separately. The leaching rates of Zn and In are 98.5% and 95.2% respectively. The experimental results shows that the valuable metals in the dust can be recovered and separated effectively by this process and the?ir recovery efficiencies are as follows: Pb94%,Sb91%, Zn84% and In69%.

Jan 1, 2009

By S. C. Sharma, M. Krishna, N. Sanmukha

"The oxidation behavior of an aluminium composite with 0, 2, 4, and 6% by weight of hematite at 200 to 500 °C has been investigated. Within the experimental temperature ranges a parabolic weight gain was observed. The, weight gain as a function of oxidation time becomes linear after an initial period on oxidation formation, an oxide scale was found whose morphology depends on temperature, cooling rate and sub-scale formation at the interface between the matrix and reinforcement. The presence of hematite particulate reinforcement has very little effect on the oxidation behavior. The interface oxidization rate was found to be higher than that of other regions. The, oxidation products were either metallic oxides or ceramic oxides. The exposure time of specimens to oxidation was 1000 minutes at various temperatures. In the present work key principles of alloy oxidation were discussed. Also the paper emphasizes various reactions taking ' place and the activation energies involved in the oxidation reactions.IntroductionMetal matrix composites (MMCs) reinforced with ceramic particulate, whiskers, or fibers have received increasing attention due to their potentially high fracture toughness and strength 1-5. Particle reinforced Aluminium MMCs find potential application in several thermal environment, especially in the automobile engine parts, space applications, such as drive shafts, cylinders, pistons, and brake rotors6.With the exception of gold, no metal or alloy is stable at room temperature, they tend to form their respective oxides. Most of the metals in the solid or liquid state are morphologically unstable when exposed to air at higher temperatures. An investigation relating to the temperature profiles of the piston area in a diesel engine has shown that the temperature can reach as high as 500¬800 K in certain regions of the piston. As the piston and cylinder areas are exposed to high temperature environment, the MMCs should have sufficient stability on both mechanical and chemical strength (oxidation). Oxidation occurs at grain boundaries in alloys and at the interface of the particulate and matrix in MMCs, which usually enhances intergranular fracture, resulting in premature failure and severe brittleness 8-10. Therefore for high-temperature applications, it is essential to have a thorough understanding of the oxidation behavior of aluminium MMCs."

Jan 1, 2000

By Yasuo Ojima

A new copper continuous converting process was investigated to evaluate the possibility of its application in the commercial operation. The tests were performed both in the laboratory and in pilot plant scale. Bath smelting process with the use of the top submerged lance technology was applied in these tests. Furnace shape was modified to a lengthwise eylindrical one with a settling area. The furnace monitor was put in the settling area to check the furnace from inside, FeOx-Si02, FeOx-CaO and FeOx-CaO-Si02 based slag systems were used to check their efficiency, The optimum slag chemistry to have good metallurgical results was discussed and FeOx-CaO system with some Si02 content turned out to be preferable although it has not been practically used, In this pilot plant test feeding rate of I tIH of solid grain matte was charged consecutively for two weeks and continuous converting could be done successively. This process is expected to overcome the problems of existing processes and be easily applied in existing plants.

Jan 1, 2003

By J. Etay, S. Daugan, Y. Fautrelle

"New type of electromagnetic parametric instabilities arising at the free surface of liquid metal in the presence of a low frequency magnetic field are presented. First, the mechanism of the instability is analysed in an idealised case. Then, the experimental device working with mercury is described. Various shapes, both regular and irregular, of free surface are found. A experimental stability diagram is obtained. Measurements of the deformation performed on photographs are compared with physical orders of magnitude.IntroductionWhen a liquid metal pool of electroconductivity a is submitted to an A.C. magnetic field B = B0 cos mt, electrical currents j are induced in the liquid metal and interact with the applied magnetic field to create electromagnetic body forces F = j x B. Those Lorentz forces comprise both a mean value (time average) and an oscillating part. Those forces are widely used in many metallurgical processes to stirr a liquid metal or to control its free surface, e. g., in aluminium continuous casting or electromagnetic levitation problems (1-3). When liquid metal free surfaces are submitted to AC. magnetic fields, the shape of those interfaces may interact with the applied field and leads to a various instabilities. A review of these instabilities may be found in Fautrelle (4). That instabilities may be a problem for the control of processing as electromagnetic levitation or quasi-levitation."

Jan 1, 1999

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

By Sven Eck, Andreas Ludwig, Menghuai Wu

"Phase separation is a frequently occurring phenomenon during solidification accompanied by melt convection, sedimentation or, in the case of two unmixable liquids, a Marangoni driven motion. In order to describe these phase separation phenomena a two-phase volume-averaging model was employed for globular equiaxed solidification of binary alloys and decomposition and solidification of hypermonotectic alloys. The model considers nucleation and growth of equiaxed grains or second phase droplets, motion and sedimentation of grains or droplets, feeding flow and solute transport by diffusion and convection. It allows the prediction of macro segregations and the distributions of grain size or droplet size. Evaluations were made by comparing the numerical predictions with experimental results. For example it is shown that the numerically predicted grain size distribution in a plate casting (Al-4wt%Cu) agrees reasonably well with the experimental analyses.IntroductionModeling of metallurgical processes is a rapidly expanding field and the research activities in the last decades cover a wide range of areas including melt pre-treatment, solidification and subsequent manufacturing routes. Among those activities solidification stands in the central position, because the primary structure of the materials, and even many defects such as porosity, (macro or micro) segregation and inclusions form during solidification. Those primarily formed structures or defects once existing are difficult to be removed or modified by the subsequent material processing.Solidification is a multi-disciplinary field involving thermodynamics, fluid dynamics and solid mechanics, heat and mass transfer, and other disciplinesr1 -31• One of the most challenging problems in solidification modeling is the complex interactions between physical phenomena occurring on different length scales ranging from atomic rearrangement over single crystal-melt interactions to heat extraction, momentum and species transport at the system level. Modeling an industry process on atomic scale is umealistic, even on grain scale (e.g. phase field method) it would need another 40 years to be able to model the exact grain morphology in a casting space envelope of 10x10x10 cm3 [ 4]. Therefore, the realistic models for industry process are based on the solution of the macro transport equations (mass, momentum, enthalpy and species) on system scale. The microscopic phenomena such as thermodynamics, nucleation law, crystal growth kinetics and interactions at the liquid-solid interface are considered with simplified models, which are coupled with the macroscopic transport equations."

Jan 1, 2004

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By Run-boWang, Fan-yi Meng, Jian-Liang Zhang, ZheWang

To elucidate the influence of high Al2O3 content on sinter softening and melting behavior, heating-up reduction test under load was carried out. In addition, microstructure study of sinter bed structure change at a different temperature was also made and the mechanism that the effect of Al2O3 content on sinter softening and melting property was discovered. SEM results showed that the increase of Al2O3 content favored the formation of Al2O3-rich slag phase, such as the eutectic (2CaO·SiO2-2CaO·Al2O3·SiO2-FeO) and gehlenite (2CaO·Al2O3·SiO2), resulting in the decrease of sinter Ts temperature. Further, high Al2O3 content improved the concentration of metallic iron and lowered the dripping temperature due to the decrease of slag liquidus temperature and viscosity. At a fixed basicity, it was indicated that there was a relationship between Al2O3 content and sinter softening-melting property. Based on the results, counter strategies to cope with the adverse effect of high Al2O3 content on the cohesive zone property were also proposed. It could provide guidance for the blast furnace operation of sinter with high Al2O3 content.

Jan 1, 2015

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000