Search Documents

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By Dale A. Zuck

Recovery of aluminum metal from drosses? is a major factor in the recyclability success story enjoyed by the United States aluminum industry. Today's modern dross processor uses the latest technology to maximize metal recovery at the lowest cost while complying with all environmental laws and regulations. Most dross processors, however, pay little attention to the resulting saltcake, the end residual of dross recyCling, and rely on landfills for .disposition of this material.. The alternative is to recycle the saltcake, but the success of this technology is dependent on the development of reliable outlets for each of the saltcake constituents. This paper discusses the evolution of an aluminum dross oxide processing technology that ,produces an economically attractive source of alumina for the production of portland cement.

Jan 1, 1995

By Oliver Zach

To know as much as possible about the condition of the refractory material (lining thickness, slag layer, build ups, ...) in an high temperature furnace is very important due to the safety and economic impacts. The new CONSCAN system offers the possibility to measure the inner surface of an furnace, and based on this results to calculate the thickness of the refractory lining, slag layer, build ups,.... The CONSCAN System provides this results as figures and graphics. This system is also working under hot conditions so it is not necessary to cool down the furnace. Based on these results the process control and the refractory lining concept could be optimized for maximum campaign life of the furnace.

Jan 1, 2006

By H. Antrekowitsch

Nowadays, the pyrometallurgical treatment in copper smelters is the common process for the recycling of metals from the electronic scrap. Furthermore the European Directive on the Waste from Electrical and Electronic Equipment (WEEE) and the Directive on the Restriction of Hazardous Substances (RoHS), increase the importance of electronic scrap recycling. Besides these a high amount of plastic and inert components in these materials leads to problems at the processing. An optimisation concerning the internal recovery and the high amount of plastic is necessary to reach the recycling quota of the European directive. The majority of the scrap is treated mechanically in order to separate in a first step plastics from metals, iron from nonferrous metals and harmful substances from valuable materials. But the quality of the different fraction often rather low and further treatment leads to higher costs. Therefore an interaction between mechanical treatment and metallurgical processing should be realised. The Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals at the Institute of Nonferrous Metallurgy at the University of Leoben carried out investigations concerning the optimisation of the metallurgical recycling and the treatment of the input materials especially of printed circuit boards.

Jan 1, 2006

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By Wantae Kim, Furnia Saito, Qiwu Zhang

"A novel mechanochemical processing technique for the preparation of zeolites from kaolinite in NaOH solution was investigated. Dry and wet mechanochemical treatments combined by subsequent moderate heat treatment could accelerate the synthetic reaction for zeolites from kaolinite. This stimulating process produced zeolite-A and zeolite-X from activated kaolinite at extremely lower reaction temperature than conventionally applied for zeolites production. Conversion to zeolite-A and zeolite-X was strongly dependent on the activated state of kaolinite. Wet mechanochemical treatment modified the chemical composition of activated solids. Rapid dissolution of AIO species rather than SiO ones in the reactant solution was accelerated by wet milling together with NaOH that promoted the formation of zeolite-X of high specific surface area.IntroductionZeolites are a family of hydrated alumina-silicate minerals contains alkali and alkaline earth metals. They have a framework structure that encloses inter-connected cavities occupied by large metal cations and water molecules. Zeolites are characterized for their ability toward ion exchange and reversible dehydration. Properties of them are exploited through commercial productions of particular structural and chemical features. Zeolites are used as commercial uses for catalysis for FCC (fluidized catalytic cracking) of petroleum refining, drying reagents of gases and liquids, and selective adsorbent for pollution control [1-3]. In such purposes, artificially synthesized zeolites are employed, although natural ones are associated with hydrothermal and hot spring alteration of volcanic materials. Commercially, a hydrothermal process has been used for the preparation of zeolite synthesis. This preparation method gives zeolites of high chemical homogeneity and purity, however, this wet-chemistry-based processing is significantly influenced by reaction temperature, pH, concentration, and composition of starting substances [4]."

Jan 1, 2000

By Chuanlin Fan

The process of flotation separation and recycling of spent potlining (SPL) was described. On the basis of the laboratory investigations, the effects of influencing factors in froth flotation process, such as grain size, flotation agent dosage, pH value, pulp density, and dissolved components concentration, etc, were carefully studied. And the influence on environment of the process was also discussed. It was found that flotation separation can be used as an environment-friendly method for treatment of SPL residue. Carbon and other compounds (include cryolite, sodium fluoride, calcium fluoride and diaoyudaonite, etc.) from SPL were separated and recycled as flotation products respectively.

Jan 1, 2009

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

By Christophe Thiébaut

Keywords: Pyrochemistry, Salts Treatment, Distillation The pyrochemical purification of metal generates spent salts. When this metal is an actinide such as plutonium, the slags cannot be discarded and are thus disposed in nuclear facility. In order to handle with these slags, the decision has been taken to reduce stored quantities. The development of a pyrochemical treatment is in progress in the CEA Valduc centre. The feed salt, typically composed of various Pu and Am species contained into monovalent or divalent chloride matrix, is first oxidized to convert the actinides into oxides. Then the chlorides are separated from the actinide oxides by vacuum distillation. Temperatures higher than 750°C for monochloride salts mixture NaCl/KCl and higher than 1100°C for divalent CaCl2 base salts, are required to produce an industrial flow of vaporization. Inactive qualification of the process for NaCl/KCl base salt has been carried out with lanthanide surrogates. Then, a pilot equipment, called distillator has been designed and built for production-scale distillation of NaCl/KCl and CaCl2 oxidized plutonium salts. Industrial flows of vaporization have been obtained with this pilot equipment : about 4 g/cm²/h for NaCl/KCl at 800?900°C and 1 Pa, and more than 1,5 g/cm²/h for CaCl2 base salts between 1000?1200°C at 0.1 Pa. The last step, now in progress, is the integration of the distillator into a glove box.

Jan 1, 2005

By Pinai Mungsantisuk

Keywords: Pd-Ni alloys, Pd-Fe alloys, Pd-Co alloys, Magnetostriction, Magnetic Properties The presence of congruent melting minima, the occurrence of ferromagnetic transition over a large composition range, and FCC type crystal structure make Pd-Ni, Pd-Co, and Pd-Fe based systems attractive candidates in our search for materials with no rare-earths, large low-field magnetostriction, and good mechanical properties. The presence of paramagnetic-ferromagnetic transition over a broad range of composition also provides opportunity for fundamental studies. In this work, we have examined the magnetic and magnetostrictive behavior of Pd-Ni, Pd-Co, and Pd-Fe alloys over the entire composition range. Alloy sample rods were prepared by arc melting and casting. X-ray diffractometer was used to obtain lattice parameter data. Magnetostriction was measured along the rod axis using strain gages. Magnetic properties were measured using a vibrating sample magnetometer.

Jan 1, 2005

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

By Toshiyuki Kawai

Copper concentrate smelting directly in P-S converters was started at Onahama Smelter in 1983. Thereafter, the tonnage of concentrate smelted through the P-S converters increased, such that by 2002, it equaled the tonnage smelted through the reverberatory furnaces. In 2003, 56% of the total copper concentrates treated at Onahama Smelter were processed directly through the P-S converters. Technical improvements are reviewed and advantages of direct smelting in P-S converters are reported.

Jan 1, 2005

By Dong Liu, Zejian Yang, Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"The structure, composition, morphology, and adsorption property of UV-vis light of as-prepared samples were characterized using XRD, SEM, FTIR-EDS, and UV-vis DRS. UV-visible light induced photocatalytic degradation of methylene blue ~) over Ti02-doped diopside was investigated. Experimental results show that doping Fe + induced the formation of Ti-0 or Ti-0-Si in diopside, and promoted the light adsorption property of diopside. Photocatalytic reactivity of Ti02-doped diopside obviously depended on content of doping Ti02. The diopside with 3% Ti02 exhibited the superior photocatalytic activity with 76% degradation of methylene blue under light irradiation for 3 h.IntroductionPhotocatalytic technology has been extensively studied in the process of dealing with inorganic and organic pollutants. Ti02, with its own non-toxic, stable, low-cost and other advantages, has become the most widely studied photocatalytic materials[l-SJ_ The low utilization quantum made it restricted in the practical application. SrTi03 as the representative of the perovskite[9·121, Bi2W06 for the composite oxide[13,141, also attracted wide interest in the photocatalytic studies. However, these photocatalytic material has been mostly prepared in relatively strict experimental conditions with chemical reagents, they had small production, high cost, which made them difficult for practical applications.In our country, there has 400 million tonnes of ti-bearing blast furnace slag (TBBFS) each year in the process of smelting pig iron, which has lead to waste of titanium resources and pollution of the surrounding environment. In recent years, studies have shown that TBBFS instead of pure Ti02 to be photocatalytic materials is feasible[ 151. TBBFS has not only been higher photocatalytic degradation activity for the o-nitrophenol, methyl orange, nitrobenzene and other organic matter[16-191,but also exhibited excellent in the process of dealing with inorganic heavy metals in waste water (containing Cr6+i201. If TBBFS can be successfully applied to photocatalytic technology, the will make large accumulation of titanium-bearing slag reasonable used, so as promote the re-use of energy. At present, our understanding of the photocatalytic activity of TBBFS is steadily deepening. Photocatalytic activity ofCaTi03 has been reported as one of the main minerals ofTBBFS [21'21J, However, there were few studies for Another major mineral of TBBFS - diopside which had the content of9-15%. diopside would doped with Ti02 In the process of smelting pig iron, therefore, Ti02-doped diopside's photocatalytic activity in the UV-Vis was mainly studied in this paper."

Jan 1, 2013

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By Andrey V. Tarasov

To carry out a physicochemical substantiation of a transition to ?soft? modes of reduction of calcine obtained by desulfurizing roasting of nickel concentrate produced as a result of copper-nickel converter matte separation in a nickel anode production circuit, an analysis has been conducted of the macrokinetic behavior of actual calcine samples in the presence of gaseous H2-CO mixtures and solid reductant additives. Within a temperature range of 900°C to 1100°C the main regularities typical of the calcine reduction process with individual gases (H2, CO) also take place when using a gaseous mixture. Under the conditions of low-temperature (900°C to 1000°C) nickel oxide reduction with products of fuel oil conversion in the presence of coke, the role of the latter is insignificant from the technological viewpoint. As a result of the present investigations, we have obtained analytical expressions of macrokinetic parameters of the reaction interaction within the [NiO] calcine-H2-CO-C-CO2-H2O-O2-N2 system.

Jan 1, 2005

By Yavuz Ali Topkaya

Rare earth ferrosilicide is a versatile alloy mainly used to control the detrimental effects of sulfur in steel and to modify graphite structures in cast iron. The aim of this study was to determine the optimum conditions to make rare earth ferrosilicon alloy using a preconcentrate produced from a bastnasite type of ore present in the Beylikahir-Eskisehir region of Turkey. This concentrate contained 23.5%REO, 41.37% CaF2, 10.69% BaSO4, 8.50% CaCO3, 4.18%Fe2O3, 2.83% Al2O3, 2.74% SiO2, 1.20% P2O5 and small amount of other oxides. The initial metallothermic reduction of this concentrate using ferrosilicon and aluminum in a graphite crucible placed in a muffle furnace gave very low recoveries due to the difficulties encountered in adjusting the slag composition, temperature and amount of additives. Therefore, two batches of rare earth oxide concentrate containing 61.1% and 81.7% cerium oxide, respectively, that were procured from a Turkish glass producer, were used to optimize with respect to temperature, duration, slag-making additives and amount of reducers. In these experiments, smelting and reduction was done in an induction furnace with graphite crucible, and, ferrosilicon and aluminum were added after melting the charge. As a result, there was no difficulty in obtaining a rare earth ferrosilicon alloy containing 35-55% RE, 5-25% Fe and 20-40% Si, with about 80% metal recovery. When the optimum conditions were applied to the preconcentrate, alloys of similar compositions were obtained with 70-80% recovery. Experiments were also done with mixtures of preconcentrate and rich concentrate, and, recoveries as high as 95% were obtained. Only in this case, to increase the recovery, mixtures had to be charged to the empty graphite crucible after heating the crucible to the required temperature.

Jan 1, 2006