Search Documents

By M. Patel, G. Djambazov, J. Shrimpton

"Removing zinc by distillation can leave the lead bullion virtually free of zinc and also produces pure zinc crystals. Batch distillation is considered in a hemispherical kettle with water-cooled lid, under high vacuum (50 Pa or less). Sufficient zinc concentration at the evaporating surface is achieved by means of a mechanical stirrer.The numerical model is based on the multi-physics simulation package PHYSICA. The fluid flow module of the code is used to simulate the action of the stirring impeller and to determine the temperature and concentration fields throughout the liquid volume including the evaporating surface. The rate of zinc evaporation and condensation is then modelled using Langmuir's equations. Diffusion of the zinc vapour through the residual air in the vacuum gap is also taken into account.Computed results show that the mixing is sufficient and the rate-limiting step of the process is the surface evaporation driven by the difference of the equilibrium vapour pressure and the actual partial pressure of zinc vapour. However, at higher zinc concentrations, the heat transfer through the growing zinc crystal crust towards the cold steel lid may become the limiting factor because the crystallization front may reach the melting point.The computational model can be very useful in optimising the process within its safe limits.IntroductionLead bullion is commonly refined by removing various impurities (e.g. copper, silver, bismuth, antimony, etc) sequentially. This in normally achieved by the addition of reagents which selectively react with the impurities and the resulting compounds removed by various means. To aid efficient mixing (ensure uniform reactions), batch mixing of materials via the aid of impellers is common practice in a number of industrial sectors. Excess zinc, added during the desilvering process can be removed by one of three methods: (1) Vacuum dezincing - During vacuum dezincing, a vacuum is drawn on the agitated molten lead within a hemispherical vessel (Figure 1). Vaporized zinc condenses on the inner top surface of the vessel. The temperature at which zinc commences to vaporize lowers owing to heating under a vacuum. This enables vaporized zinc to be recovered in the form of high purity crystals without oxidation. The zinc crystals are recovered once the vessel lid is removed and the vacuum is broken. (2) Chlorine dezincing - In chlorine dezincing, molten desilvered lead is reacted with chlorine gas, forming a surface layer of zinc chloride contaminated with small amounts of lead chloride."

Jan 1, 2004

By M. Furuta

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating without a slag cleaning furnace (SCF) since its start-up in 1972. It has used its own developed coke combustion technology, the Tamano-Type Flash Smelting Furnace (T-FSF). The coke combustion technology that is the core of the process, along with the installation of a computer guided system and the improvement of the concentrate burner combustion in the T-FSF have all contributed to having acceptable copper loss levels in the slag without using a SCF. However, recently, because a high concentrate charge rate has been used in order to achieve a high matte grade in the T-FSF, a short settling time has been experienced and copper losses in the slag have become difficult to maintain at a lower level. Furthermore it is estimated that copper losses will further increase after the completion of the next expansion because with the aim of having a higher matte grade operation at 67% less coke will be charged and the reduction effect of the settler will be smaller. Therefore, in order to maintain the copper losses in the slag within proper levels the installation of SCF was decided. This paper, describes the operation before the introduction of SCF along with some theoretical considerations of slag chemistry.

Jan 1, 2006

By Aly M. Abdel-Rehim

The present work deals with a study of the mechanical activation of processing of Egyptian monazite by its simultaneous ball-milling and pressure leaching in order to improve the recovery of thorium and lanthanides from monazite. Experiments of simultaneous ball-milling and alkaline leaching of monazite contrary to autoclave leaching were carried out in stainless steel ball-mills of cylindrical shape under different conditions of temperature, pressure, time and alkali amount and strength. The ball-mills were heated and mechanically rotated in an electric furnace by means of roll mechanism. The effective rotation speed was fixed at 130 rpm in all tests. The charge of steel balls of different diameters was equivalent to 45% of the total mill volume. Monazite was charged in ball-mill without preliminary grinding. It is found that high rate of monazite leaching by ball-milling leaching method is achieved at lower temperature, shorter time and lower expense of alkali than in autoclaves. The results obtained show that complete recovery of thorium and lanthanides from monazite (99.8%) by simultaneous ball milling and alkaline leaching is attained at 140°C within 2 h. It is concluded that processing of monazite by its simultaneous ball-milling and leaching is mechanically activated and accelerated as a result of grinding action of steel balls that caused the continuous removal of the hydroxide product from reacting particle surfaces. This leads to the exposing of fresh and activated monazite particles surfaces to alkali leach solution and consequently the acceleration of the reaction of monazite processing.

Jan 1, 2006

By Ignacy A. Lipiec

The advantage of microorganisms used in bioleach systems to conventional chemical reaction systems is that these apply the available energy more precisely where it is needed, either directly onto the mineral of interest or by efficiently catalyzing the production of a reactant. The literature cover the range from empirical models used in describing macro heat balance in heaps to detailed studies relating the micro heat effects of bacteria adhesion energy to the surface of minerals. In this paper, the heat effects are reviewed in a general way describing bioleaching in two macro systems, heap leaching and slurry bioreactors. The micro scale heat effects is the reactions and conditions at the microorganism scale, including the mechanism of leaching and bacterial behavior.

Jan 1, 1998

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By Natasa Mitevska

The statistical analysis of the slag composition influence on copper losses to discard slag in the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Yugoslavia) is presented in this paper. The model for the slag basicity calculation is determined, and connected to the copper distribution coefficients between the matte and slag phase. The influence of all components on the slag structure is also illustrated.

Jan 1, 2003

By Katsutoshi Inoue, Shafiq Alam

Several novel types of chemically modified chitosan were prepared by immobilizing functional groups of EDTA and DTPA onto polymer matrices of chitosan in order to investigate their potential for mutual adsorptive separation among rare earths. Following the batch wise adsorption tests to elucidate their basic adsorption characteristics for rare earths, mutual separation was carried out using a column packed with the chemically modified chitosan. The separation between Sm(III) and Y(III) was tested using a column packed with EDTA-type chitosan while mutual separation among 4 light rare earths, La(III), Ce(III), Pr(III) and Nd(III) was tested using a column packed with DTPA-type chitosan. In both cases, satisfactory mutual separation was achieved by the chromatographic operation using these chemically modified chitosan.

Jan 1, 2014

By C. Abruzzese

This work concerns a process for the inertization of asbestos-containing wastes and the subsequent recycling of the inerts for the production of ceramic refractories. One of producted refractories is cordierite, that is widely used in the electronics industry and also in mechanical engineering for the manufacture of catalytic converters for automobiles. The process thus achieves the twofold objective of eliminating toxic and harmful refuse containing asbestos, while making available high-tech materials at a reasonable cost.

Jan 1, 1998

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By J. E. Sallee

An experimental study has been conducted on the level of arsenic contamination in samples of zinc oxide when the zinc oxide is contacted with gas mixtures containing As4O6(g). This contamination has been determined as a function of A4O6 saturation pressure, temperature, zinc oxide sample surface area, impurities, and oxygen level in the gas mixture. The results indicated a rather clean separation can be achieved between condensed zinc oxide and gaseous arsenic oxide as long as attention is given to temperature control, and the final zinc oxide surface area. For a 300°C operation temperature and an AqOg saturation pressure of 0.38 TORR (or 0.05% As406 by volume), the contamination level is expected to be approximately 100 ppm. This suggests that arsenical dusts can be treated in the HRD flame reactor process and a reasonable purity zinc oxideproduct produced. The results also show no evidence of zinc arsenite or zinc arsenate formation.

Jan 1, 1994

By Hsin H. Huang

Equilibrium calculational software programs can be effectively utilized to model the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation on extraction and recovery processes. Illustrative examples using the calculational program ST ABCAL for the creation of diagrams such as EwpH, activity or concentration-pH, and activity or concentration-EH are presented to demonstrate the fundamental characteristics of real hydrometallurgical mercury dissolution and recovery processes. An industrial application will include leaching of mercury from K 106 mercury sulfide waste and solution purification by iron cementation.

Jan 1, 2003

By Juan B. Cabezas

"The favorable characteristics and workability of plastics as a replacement of wood, lead, stainless steel, asphalt and other materials are described. Various types of plastic have proven to be the most favorable choice for handling a variety of acidic, alkaline and organic solutions, as well as pulps, chemical wastes, slurries or tailings for impoundments. The material origin of various plastics, methods of manufacturing and specifications applied to leaching solutions are discussed, including availability and costs. Examples of select plastics are considered for use as alternatives of other materials under severe environmental requirements.IntroductionHydrometallurgical processes applied to gold recovery, as well as other metals, require the use of strong solutions of alkaline, acidic or organic nature, and may also include a variety of materials with extraneous characteristics and complications for handling in storage.The technology of leaching has been in use for more than 100 years, but the applications of leaching processes in metallurgy have become more commonly used in the last 15 years. Suitable materials for the construction of containers, launders, piping, and various accessories, to be used in the handling of leach solutions or slurries, have become a serious problem. Various metals such as brass, lead, stainless steel, etc., and non metallics including wood, clays, glass, rubber, ooncrete, tars or miscellaneous compounds have been tried in the past with serious limitations in workability and resistance to wear and corrosion. For example, the use of metallic, wooden or glass piping systems would require extraordinary shop maintenance to keep such systems in operation"

Jan 1, 1997

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Gerard M. Ludtka, Xiaoping Niu

"A constitutive model has been developed to predict the yield strength aging curves for aluminum casting alloys during non-isothermal age-hardening processes. The model provides the specific relationship between the process variables and yield strength. Several aging heat treatment scenarios have been investigated using the proposed model, including two-step aging recipes. Two-step aging heat treatments involve a low temperature regime to promote nucleation of secondary phases and a second step at higher temperature for the growth of the secondary phases. The predicted results show that a yield strength of approximately 300MPa might be obtained in a shorter aging time, of approximately 30 minutes. As a result, better mechanical properties can be obtained by optimizing the time-temperature schedules for the precipitation hardening process of heat treatable aluminum alloys.IntroductionA356 is one of the commercially heat treatable aluminum casting alloys, and T6 is one of the heat-treated conditions to improve mechanical properties. The first stage of a T6 temper is solution treatment at an elevated temperature, generally in the range of 480 - 540°C. After solution treatment, the cast part is typically quenched in water/air to retain the solute-rich homogeneous matrix chemistry at room temperature. Subsequent ageing treatment stages capitalize on this super-saturated solid solution to generate controlled dispersions of very small strengthening precipitates within the matrix of Al grains [l]."

Jan 1, 2013

By Chi-Ming Chang

Alloy powders are commonly used in the purification of zinc sulfate solutions for use in standard electrowinning practice. The primary goal of this research was to study the use of zinc-lead alloys for similar reactions in the galvanic stripping of impurities from organic solutions. The effects of various parameters on the electrochemical behavior of commercially produced zinc-lead alloy powders were determined. A qualitative evaluation and summary of the influence of the more pertinent parameters on iron removal from di-(2-ethylhexyl) phosphoric acid (D2EHPA) by galvanic stripping is given. Water concentration, oxygen content and reaction temperature were the principal factors affecting the reaction rate and process efficiency. Activation energies were also calculated and indicated that the reaction changes from chemical to diffusion control .with increasing temperature in the range of 35" to 45°C. The results showed that zinc-lead alloy gave faster reaction rates with less sensitivity to process variables than SHG zinc as a reducing agent for galvanic stripping. The role of lead could be as cathodic sites for the reaction which enhances the zinc dissolution or anodic half reaction. The morphology of the zinc-lead alloy surfaces, before and after the reactions, supports this assumption.

Jan 1, 1998

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002