Search Documents

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By N. Tsuneyama

Sumitomo Metal Mining Company has been operating Waelz Kiln at the Shisaka Works for 12 years to recover zinc and lead from electric arc furnace (EAF) dust. To increase the capacity and cut down the operating cost, some improvements have been carried out resulting in the capacity of 60,000 t/ y of EAF dust as compared with 32,000 t/ y in 1977. The current capacity is equivalent to 20% or EAF dust generated in Japan. The number of workers has been decreased by the introduction of an automatic control system, and the productivity per worker is now twice as much as 10 years ago. This paper will describe the progress of the operation at the Shisaka Works after the previous? paper reported in "Zinc' 8 5? and summarize the status or EAF dust recycle in Japan.

Jan 1, 1990

By Lawrence D. May, Harry Mudgett

"In the course of developing a new industrial process, information produced at the Research and Development (R&D) stage is critical to determining the technical and economic feasibility of the project. Understanding the fundamental operating parameters for each unit operation in a flowsheet typically comes from historical knowledge of similar systems or by technical development through a robust research program. This approach holds true for processes incorporating fluidized-bed technology. In this paper, the authors will present a practical approach for performing a research study that will allow a process owner to determine if the concept of using a fluidized-bed system can become a reality. Included are discussions of key steps required at each level of the R&D program, and the critical information required for advancing the project to the next stage.IntroductionThe conduct of a research and development program typically starts with a process owner identifying a new industrial need or modification to an existing operation. The owner can pursue this need through multiple routes, including initial in-house development, coordination through an engineering firm, contacting suppliers of key equipment envisioned for the process, or through direct contact with research and development organizations. Where and when the project is conducted is as variable as the number and types of owners who pursue them. Factors that can influence the decision of where to conduct a research program can include the type of process desired, the scale and scope of the project, the location of the project site relative to the R&D options, the experience, capability, and availability of the potential research sources, and the costs to conduct the program. Often, the owner may choose a combination of the available resources to achieve their objectives. In the end, the owner's choice should be based on a thorough understanding of their goals and objectives for the program, and a good understanding of how to measure success while achieving those objectives. Herein, the authors will describe the methods we have typically used to develop the information an owner needs to make an educated decision for investing in a new or modified process."

Jan 1, 2014

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Carbonaceous refractory materials are widely accepted in many reducing smelting processes such as iron and ferroalloys. Oxidizing processes such as copper concentrate smelting traditionally use magnesia and/or alumina/silica refractory materials. The main objection to the use of carbon-based refractories as the exposed working lining in oxidizing applications is the potential for free oxygen to react with the carbon at high temperature, which could rapidly degrade the refractory lining. In 2013, Outotec and GrafTech conducted joint trials of a thermally conductive, carbonaceous lining for smelting copper concentrates in the Outotec® pilot-scale top-submerged-lance (TSL) furnace in Dandenong, Australia. This testwork had two equally important goals; to demonstrate the ability of carbon refractories to withstand oxidizing process conditions, while ensuring that neither furnace operating conditions nor process stability were negatively affected by the refractory material. The paper discusses the input parameters of the trials, key observations during the testwork program, and the results and conclusions from both process and refractory design standpoints.

Jan 1, 2016

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Richard D. Hagni

Process mineralogy has not been given adequate attention in years past, because geologists have not been sufficiently interested in applying mineralogical techniques to industrial processes, and most process engineers are not adequately trained to use them. Although some individuals and institutions have made efforts to improve the situation, it is only in the last few years that the significance of applying the methods of mineralogy to a wide variety of industrial processes has been fully appreciated. Presently, the formation and organization of several groups devoted to applied mineralogy have created a more amenable climate for the development of process mineralogy. As a result, the presentation, discussion, and publication of the results and case histories of process mineralogy have become fairly common. Short courses affording hands-on experience with applied techniques are now available to the many geologists and process engineers engaged in industrial mineralogical processes. The future role of the process mineralogist is viewed as an expanded one, which will increase in value.

Jan 1, 1982

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990

By I. H. Bonekamp

Norddeutsche Affinerie has operated an Outokurnpu type flash smelter for more than 25 years. In recent years, the concentrate smelting capacity was increased to 750,000 tpy, double of the initial design capacity. Maintaining this high performance level requires very good metallurgical process control. It is not enough to base this control on thermodynamics and kinetics since the furnace is highly dynamic. Understanding these dynamics and being able to quantify them can have significant financial benefits. A mass and energy balance model was developed and is discussed based on measured data. At this time the model is based on the major elements copper, iron, sulfur and silica. With it is possible to quantify the differences of the various material streams such as matte, slag, flue dust, matte carry-over to settling furnace, etc. Comparing the reconciled energy balance model with the fundamental thermodynamic model makes it possible to quantify the dynamics. These dynamics are related to input parameters using methods such as statistics and neural nets. In the future this database will be used to improve the understanding of the dynamic process as well as the dynamic process control.

Jan 1, 1999

By Matthew Tunnicliffe, Akram Alfantazi, Paul Nesbitt, Farzad Mohammadi

"Lead and its alloys are proper candidates for anodes in electrowinning processes mainly because they are insoluble in the leach solutions and relatively cheap. However, the annual cost of corrosion problems associated with these anodes is millions of dollars. In this study lead-silver and lead-calcium anodes were tested under typical nickel electrowinning conditions and the effect of chloride on the corrosion performance of the anode materials was investigated. Corrosion rates of the anodes were calculated using the discharge plateau (reduction of lead dioxide to lead sulfate) after galvanostatic experiments. It was found that lead calcium anodes have the highest corrosion rate both in the presence and absence of chloride. Surface morphology of the electrodes was studied using SEM and the corrosion products were characterized using XRD.IntroductionLead (Pb) is usually the preferred material for commercial anodes since it is insoluble in the leach solution and the costs are manageable. One advantage of using an insoluble material as an anode is the higher purity of the cathodic deposits and better quality of the end product. During nickel electrowinning, metallic nickel is deposited on the cathode while oxygen evolution reaction (OER) takes place on the anode. In practice, relatively high potentials are necessary for the reaction to proceed at the desired rate because of the high overpotential of OER on lead. Lead anodes get oxidized in typical electrowinning conditions and usually have two to three years of lifetime. Although the price of each anode is insignificant, the overall cost of corrosion of these anodes is considerable, which is due to the large number of anodes used in a plant, typically two to three thousand. Therefore, corrosion is a significant problem associated with lead anodes in commercial nickel electrowinning plants and industries show interest in addressing this problem. Corrosion of lead electrodes in acidic environments has been previously the subject of many research studies [I-7]. It has been reported that, during the anodic polarization of lead, several phases may be present on the surface, depending on the potential range that is being studied [8]. Lander showed that lead is oxidized at potentials higher than 0.252 YsHE with tetragonal lead monoxide being the main reaction product [9]. At 0.666 YsHE lead can transform to lead dioxide; however, it is not stable and transforms to lead sulfate and lead oxide. At potentials higher than 1.684 YsHE, lead dioxide is eventually a stable phase and forms a protective layer on the surface [I 0, 11]. Under conditions of a typical nickel electrowinning plant, usually a 200 A/m2 current density is passed through the electrodes."

Jan 1, 2012

By Adrien Antenen, Didier Villette

CITRON has developed a new process for the recycling of hydroxide sludge, household batteries, catalysts, automobile shredding residues, grinding sludge and other metal containing organic and inorganic waste. A pilot plant with a capacity of 1,000 tons per year has started operations in April 1998. In August 1999, an industrial plant became operational with an initial treatment capacity of 23,000 tons.

Jan 1, 2000

By H. A. F. de Souza, Dana S. Mills, P. E. Burgener

"ICP-MS has moved from a laboratory curiosity to a functional analytical tool. This paper discusses how ICP-MS has been used to solve difficult analytical problems encountered when analyzing various mine materials. Comparisons between analytical techniques applied to the analysis of gold and the platinum group metals illustrate the advantages and problems of ICPMS when. applied to trace levels of some metals iri the presence of ore grade metals. Interferences and matrix effects are compared to ICP, AA and Neutron Activation. The necessity to select chemical extractions which are compatible with ICP-MS are also discussed.The ICP-MS techniques explained in the examples on Au and precious group elements (PGE) have validity in analytical problems encountered in testing of trace metals in the presence of major elements found in mine materials. Exploration and environmental testing are other areas that require the same analytical approach to quantify trace levels in the presence of major interfering elements normally associated with mining environments."

Jan 1, 1999

By Adam C. Powell

A new Cahn-Hilliard phase field model of transport-limited electrochemistry describes phase boundary motion due to oxidation and reduction reactions at metal-electrolyte interfaces. Benchmarks demonstrating the accuracy of the method include open circuit voltage and closed circuit current in metallothermic reduction, and linear stability theory in metal electrolysis, including a new stability criterion for reduction of liquid metal from liquid electrolyte. The model is applied here to understanding cathode interface stability in titanium electrolysis e.g. in the SOM process developed with Uday Pal, and to structure evolution in subhalide reduction of titanium dichloride by magnesium developed by Toru Okabe. Potential for application to new fuel cell and battery systems is also discussed.

Jan 1, 2006

By P. Chris Pistorius

An example is presented to illustrate the joint effect of local reaction equilibria and mass transfer limitations, for reactions during ladle refining of steel. The example relies on some of the kinetic principles that David Robertson has employed to quantify many metallurgical processes. In calcium treatment of alumina inclusions in aluminum-killed steels, solid CaS forms as an intermediate reaction product. During subsequent reaction, CaS disappears and calcium aluminate forms; at the same time, aluminum and sulfur dissolve in the steel. Kinetic analysis shows that the rate of this reaction is not limited by mass transfer of dissolved aluminum and sulfur away from the reacting inclusions. The reaction rate is likely limited by transport of dissolved calcium. This example also illustrates the use of FactSage macros for kinetic modeling.

Jan 1, 2014

By Arpad E. Tonna

Recycling of materials from lithium-oxyhalide batteries is a complex task, since the dismantling of batteries is associated with many hazards. The electrolyte and the lithium anode metal are extremely reactive in the presence of water or water vapor. Therefore, the dismantling process is a complex task. In this process, the lithium battery is electrically discharged, then frozen in liquid argon, and cut into small size pieces. These are fed into an incinerator, where the unreacted portion of lithium metal, thionyl chloride, plastic separators and carbon paste are decomposed and burned to gaseous products. The aluminum, iron (steel) and nickel pieces are recovered as saleable scrap metals. The off-gases are scrubbed with an alkaline sodium carbonate containing solution. The clean gases are released to the environment. The particulate mater recovered from the scrub-suspension would be available as additive to the cement industry . The recycling of battery decomposition products improves the economic viability of the disposal processes. Work is in progress to develop safe handling, processing and recycling large size lithium batteries.

Jan 1, 1995

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By D. J. Murdock

Cominco Ltd. has developed a number of innovative technologies for electrowinning. The paper discusses the application of these technologies to the copper industry. Tankhouse and cell design will be discussed in addition to anode cleaning and cathode handling. Specific examples of the application of this technology to the copper industry are cited.

Jan 1, 1987

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012

By W. G. Davenport

A survey of world copper refining tankhouse .practices has been carried out. This paper compiles the results and examines changes in operating practices .since the similar 1987, 1991 and 1995 surveys. Continuing trends are the installation of ISA Process and Kidd Process stainless steel cathode technology, polymer concrete cells, anode preparation machines and automatic cranes. Instrumentation and automatic control are increasing, particularly for addition agent optimization; solvent extraction .and ion exchange techniques are being increasingly applied for electrolyte purification. The overall consequences of these changes have been 'improved cathode purities and enhanced tankhouse productivities.

Jan 1, 1999

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000