Search Documents

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapoconcentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporate playa lakes.

Jan 1, 1997

By Brad C. Lewis

The coal mining industry has experienced a general trend toward longwall operations. An increasing percentage of underground coal is being mined by longwalls. And productivity in longwalls is likewise increasing. Operators of longwalls, however, have not yet reached a state of mining euphoria. Competitiveness within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. [Figures 1, 2 and 3] present trends in the industry. Longwall mines, as defined here, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Nonlongwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation. Annual percent increases in productivity appear to have peaked in the 1985-1987 time frame. This was due, in part, to implementation of technological advancements and improvements in management-labor relations. The results shown in [Fig. 3] aroused the author's curiosity. The first question was "Have technological advancements to increase productivity peaked?" It does not appear so.

Jan 1, 1990

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By Lewis L. Oriard

INTRODUCTION In recent years, there has been a trend in the direction of larger drilling equipment and larger diameter blastholes. Although this change has improved the efficiencies and reduced the costs in many operations, it has increased the potential for damage to underground openings. In addition, in many instances one now finds more sophisticated delicate instruments, automated control facilities, and a large variety of structures in proximity to blasting activity. The combined effect of larger-scale blasting activity and its proximity to various features of interest is such that there is an increased need for a more refined analysis of blasting effects and their control. BLASTING EFFECTS ON ROCK SURFACES The Breakage Mechanism In order to develop techniques for controlled blasting, one must first understand the features of the mechanisms by which blasting causes rock breakage to occur. These features have not been easy to demonstrate, mostly due to the difficulty in making tests and observations at the high stress levels and short time durations involved. When an explosive charge is detonated, the material surrounding the charge is subjected to a nearly instantaneous, very high pressure [on the order of 1.4 to 13.8 GPa (0.2 to 2.0 X 106 psi), depending on the explosive]. If the charge is coupled to "average" rock, this pressure will pulverize the surrounding rock for a distance on the order of 1 to 3 charge radii in hard rock, and to a greater distance in softer rock (this is also dependent on the type of explosive). As the pressure wave passes into the rock, high tangential stresses cause radial cracks to appear, and the nearly discontinuous radial stress zones gen¬erated by the shock front may cause tangential cracks to appear. The extent of these cracks depends on the energy available in the explosive, how quickly the energy is transmitted to the rock, and the strength properties of the rock. The discontinuous shock front is quickly dis¬sipated, but the expanding gases generate a longer-acting pressure. A compressive pulse travels to the nearest face or internal rock boundary where it is reflected in tension. The tensile strengths of most rocks are roughly 40 to %o of their compressive strengths, so the rock may now fail in tension whereas it may have been able to support the diminished compressive phase without failure. The ten¬sile deflection typically produces a failure described as tensile slabbing or scabbing. Laboratory experiments and field experience have pretty well established that several mechanisms are involved. These include (1) the classical case of tensile parallel slabbing when the pressure pulse is reflected at a free surface; (2) failure under quasi-static compressive loading (the shape is normally irregular due to discontinuities in the rock); (3) radial cracking under the action of tangential stresses at the periphery of the expanding pressure pulse; (4) peripheral cracking at the discontinuous shock front which is quickly dissipated; and (5) additional mass shifting due to the venting of the explosive gases. The first three items have received much attention in the laboratory and the literature. The complex effects of gas venting are difficult to test in the laboratory because of the difficulty in reproducing the many weak planes and discontinuities typical of most field conditions, which play such a prominent role in determining the behavior of the rock mass subjected to blasting. Unfortunately, gas venting effects can be pro¬jected to significant distances under certain field conditions, and are sometimes difficult to control. It is not unusual for gas venting to be the overriding factor in determining the final geometric shape and physical condition of the finished excavation. Sources of Damage For the purposes of this discussion, damage includes not only the breaking and rupturing of rock beyond the desired limits of excavation but also an unwanted loosening, dislocation, and disturbance of the rock mass the integrity of which one wishes to preserve (such as mine pillars, underground openings, etc.). The sources of damage include, of course, all those physical features of the rock breakage mechanism. Each of these effects must be limited to the desired zone of breakage and excavation if the integrity of the remaining rock mass is to remain undiminished. The primary zone of rock breakage usually can be controlled in the normal process of field experimentation to determine proper charge sizes and location for primary excavation. However, it frequently happens that there is damage from sources which are more difficult to account for in the design process, which are often overlooked. These are (1) the overbreak due to poor drilling control, (2) dislocation of rock (mass shifting) due to venting of explosive gases, and (3) loosening or dislocation due to the influence of seismic waves (ground vibrations). CONTROL OF ROCK BREAKAGE Importance of Geometry In studying the rock mass and blasting design con¬siderations, it is important to keep in mind the geometric relationships among charge size, shape, and position, and the physical features of the rock mass to be preserved. The features of principal interest are the external shape and position of the rock mass relative to blasting, and the position and attitude of any weak planes in the rock mass. The Sequence of Blasting and Excavation Events Unfortunately, there are too many times when the task of preserving delicate rock is considered hopeless, and because of this attitude, no further effort is ex¬pended towards caution or control. In such cases there is often a failure to recognize the importance of the se¬quence of the procedures. Attention to this can greatly reduce unwanted effects at minimum cost. Perimeter Control The requirements for perimeter control are highly dependent on the special needs of each particular proj¬ect. The desirable degree of control is a highly variable

Jan 1, 1982

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By Mark J. Zdunczyk

"Frac sand is industrial silica sand much like glass, foundry, filtration and blast sand. The sand must meet certain specifications set forth by the industry that consumes the product. The production and consumption of frac sand has experienced record growth in the last 10 years because of new oil and gas drilling, new horizontal well drilling, multi-stage fracturing and the stimulation of older wells that have little or no production. Frac sand is needed to “prop open” the fractures in the rock reservoirs to allow oil and gas to flow out more freely.According to the U.S. Geological Survey (USGS), the estimated production of frac sand in 2015 was 71 percent of the total production of industrial silica sand or 67.4 Mt (74.3 million st). This is a decrease of about 12 percent from 2014. However, the silica sand industry and other industry sources estimate only 50 Mt (55 million st) of frac sand were produced in 2015. In recent years both the USGS and industry studies have been very close in estimating the production of frac sand but with the recent downturn in frac sand production, perhaps, reporting to the USGS was not as accurate. These discrepancies may be that the USGS statistics are based on voluntary reporting by the industry and some companies report their approximate production, others may not. It is always difficult to obtain accurate production figures of any industrial mineral or construction aggregate operation as most companies tend to keep those figures somewhat confidential. It is certainly accurate to report that the production of frac sand had decreased since the last quarter of 2014 and through 2015. The oversupply of oil and natural gas has led to this decline in frac sand usage. Oversupply has idled drilling rigs and well completion activities. World Oil Magazine reports that 2015 was the worst year for rigs in a quarter century. The only wells being completed are those that have contract agreements to do so, others have been capped. Very few new wells are being drilled. Since about 98 percent of well completion is sand and water, the sand supply has caught up with the demand. There are some bright spots in the “oil patch” as the Permian Basin in Texas and the Woodford Shale in Oklahoma have kept pace somewhat with drilling and completion. It has been reported that the frac sand producers in the Brady-Voca, TX area are producing to nearly capacity. The northern frac sand producers like those in Wisconsin, Illinois and Minnesota are feeling the downturn because of the cost of shipping sand to these moderately active basins and plays. The “rule of thumb” is that freight is 2/3 and sand is 1/3 the cost."

Jul 1, 2016

By Erica McGlynn, Brian Negrea, Lance Jackson

There was no need for the people of Cleveland to ask “Where does the raw sewage go? We want to know!” because it was clear. The raw sewage was being discharged into Lake Erie during heavy rainfall events due to the outdated design of the combined sewer system. In efforts to resolve this ongoing issue for the City of Cleveland, the Northeast Ohio Regional Sewer District developed Project Clean Lake in collaboration with the US EPA. Project Clean Lake is a 25-year, $3 billion program consisting of seven large-diameter CSO storage tunnels to be constructed beneath the city’s existing infrastructure. The first four tunnels have been completed using traditional hard rock TBM excavation methods. The fifth tunnel, the Shoreline Storage Tunnel Project, presents unique challenges and complexities as it will be the first large-diameter EPB TBM to dig under the City of Cleveland. The project itself consists of one tunnel drive 14,100' (2.7 miles) in length, two pipe jacking tunnels, three large slurry wall shafts, two diversion structures, and three regulator reconstructions. Upon completion of the project, 12 permitted CSO locations along Lake Erie will be taken offline, reducing overflow volumes by approximately 350 million gallons per year. This paper will discuss the current status of construction and the chosen means and methods, including the myriad of nuanced differences between hard rock and EPB TBM tunneling methods. Particular attention will be given to the site preparation, setup, and organization; TBM assembly; and TBM launching practices.

Jun 13, 2023

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By James J. Gusek

The Atlantic City iron mine is located in Fremont County in central Wyoming, near the historic gold mining camps of Atlantic City and South Pass City. The mine lies on the southeast flank of the Wind River Mountains at an elevation of about 2,470 m (8,100 ft) above sea level (Fig. 1). An 81-h M2 (200-acre) tailings impoundment at the Atlantic City taconite operation has been a source of blowing dust. The site qualified for reclamation under Wyoming&apos;s Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction incorporated commercially available organic amendments and fertilizers into a 300-mm- (12-in.-) thick cap of a sterile clay loam cover material. The water level was lowered in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin. A wide tailings pond spillway was built that allows flood control while minimizing seasonal water-level fluctuations in the pond. Rock berms and rock snow fences were built for wind-erosion control and soil-moisture preservation. Future work includes tree planting in the protective wind/ snow shadows of rock berms and rock snow fences and plugging a decant pipe. US Steel opened the Atlantic City iron mine in August 1962. It closed in 1983. Taconite iron ore was mined by surface methods. The ore was magnetically separated from the waste. The magnetic concentrate was mixed with bentonite, formed into pellets and roasted to produce a blast furnace feed stock for US Steel&apos;s blast furnaces in Geneva, UT. The pellets were hauled by rail to the Geneva Iron Works. The Atlantic City Mine produced three types of wastes. These included waste rock overburden from mining, a coarse-grained (sand to small-gravel sized), nonmagnetic reject rock termed "cobbs" and fine-grained tailings ranging from 600 to 75 µm (28 to <200 mesh). The waste rock has been used as an aggregate/rip rap source by a local contractor and the Wyoming Department of Transportation (WYDOT). WYDOT also

Jan 1, 1998

By Dennis C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required about 3 Mm2 (32.3 million sq ft) of fill over an area of about 600,000 m2 (6.5 million sq ft) in irregular terrain with relief of up to 40 m (130 ft). Earthwork construction was completed in about six months using mine waste, placed in 4 to 6 m (13 to 20 ft) lifts with mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10 m (33 ft). This was done to develop a mat for additional resistance to possible differential settlements due to the modest density of the fill and dynamic (earthquake) conditions. A single 2-mm (80-mil) high-density polyethylene (HDPE) liner was used below the leach pads. This was protected from the loading and unloading equipment by bedding and cover systems. It consisted of screened sand, gravel and silt as the bedding and cover layers and a heel of screened gravel and primary crushed low-grade ore.

Jan 1, 1995

By J. Stachurski, N. A. Abdel-Khalek

The objective of this investigation was to compare the results of countercurrent, column cell flotation vs. conventional (mechanical) cell flotation for the cleaning of a sulfur ore (-0.5 mm, 27.43% S) and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, column flotation produced concentrates of higher grade. For example, column cell flotation produced a nonwashed concentrate of 65.3% S with a recovery of 84.1%. However, conventional cell flotation produced a rougher concentrate of lower grade (57.0% S) and higher recovery (92.5%). At a superficial-wash water velocity of 0.265 cm/sec, the column product grade increased to 76.4% S, with a slightly lower recovery (80.3%). However, a concentrate with a similar recovery but a lower grade (74% S) than that of the washed product was obtained after three cleaning stages with the conventional cell. The column gave superior results for the flotation of fine and ultrafine particles.

Jan 1, 1994

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By Malcolm Wills

Boddington Gold Mine commenced operation in 1987 with an initial production of 3.0 Mt/y at a grade of 3.5 git. Head grade has reduced over the life of the mine and the major response to the drop in grade has been to increase mining rates and increase plant throughput. A capital expansion was carried out in 1996 increasing the throughput to 6.0 Mt/y and since that date tonnage has been increased without major capital expenditure. BGM's current mill throughput is 8.77 Mt/y ( 1999). In 1999 the combined basement plant and direct leach plant processed 8,770,055 tonnes to produce 233,507 ozs or 7.262882 tonnes of gold at an average head grade of 0.83 git. With grades of 0.83 git, and gold price at record lows, $US251.95loz in August 1999 or $A393.67loz it has been necessary to make and maintain major cost savings to remain profitable. Boddington Gold Mine has achieved this by a number of steps including a productivity study by outside consultants.

Jan 1, 2000