Search Documents

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Christophe Bragard, Marte Gutierrez, Haotian Zheng, Michael Mooney

This paper proposes a framework for applying surrogate-based approaches to evaluate SEM construction, which can both benefit the uncertainty analysis in the design stage and real-time calibration during the construction process. The performances of four surrogate modeling approaches, namely back-propagation neural network (BPNN), support vector regression (SVR), random forest (RF), and polynomial chaos expansions combined with Kriging (PCK), were evaluated and compared. A variance-based global sensitivity analysis (GSA) was performed on the surrogate predictor to quantify the impacts of geotechnical parameters on the deformation responses induced by SEM tunneling. The Regional Connector Crossover Cavern project constructed in Downtown Los Angeles was set as the benchmark problem to demonstrate the efficiency and reliability of the proposed procedure.

Jun 13, 2021

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

By H. Lyn Bourne

This is the sixth annual tabulation that gives mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data plus more than 100 new entries. In addition to the royalty information, some entries show the cost of purchased reserves. An article in the December 1984 Kentucky Coal Journal could have far reaching applications. It explains that a banking firm examined the "reserve risk" as one of six factors for analysis when financing a coal project. The firm concluded that coal reserves in Kentucky are worth an average of $0.29/t ($0.26 per st) in-place. The banking firm based this in-place value on its examination of more than 50 leases. In-place value is especially important when trying to establish a mineral value for a given deposit. Ernie Lehman wrote to this author after last year's column appeared and he quoted the lease rates for lead and zinc on federal land. He states, from first hand information, that the leases are based on a percentage of net smelter return as follows: 4% for the first five years, 4.5% for the next five years, and 5% thereafter. The figures used in last year's column ($ per st) came from dividing reported royalty income by reported production. The information reported last year merely translates the results of the net smelter return (as written in the lease) to royalty income per ton to the US Government for the various years. Statistics from the Minerals Management Service of the Federal Government show that oil and gas account for 40% and 53%, respectively, of the Federal royalty income. Coal accounts for about 4% and all other minerals, the remaining 3%. Oil and gas leases are mostly at 12.5%. Most of the coal leases are at 12.5% for surface mining operations and 8% for underground mining. Many of the other commodities are leased at 5%, which has been true for decades. Relative to Federal leases, this year's table shows some percentages and some costs per ton. This was done to give information about the leases and also to show income produced by various commodities. Note that some commodities have a variation in $/ton even though the royalty percent is the same. These variations result from a combination of factors that influence the value of a mineral commodity. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation (especially significant for most industrial minerals); • market conditions both for the commodity and the company acquiring the right to mine it; *quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give the location - either by state, US geographic area or Canadian province; the cost - R for royalty and P for purchased cost; and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cu ft), tons (/T, 2000 lbs) or acres (/A). 1 cu yd = 0.7646 m3 1 cu ft = 0.2832 m3 1st=0.9078t 1 acre = 0.4047 hm or m2 In several cases, the royalty is a percentage of the sales price of the finished product and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: G. Anderson, B. Brown, R. Ganis, K. Hauser, E. Lehman, and S. Sims. Their help is appreciated as are the contributions by those who asked to remain anonymous. This column requires additional information each year. That data must come from people in the minerals industry who have royalty information. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write the author at the address given in the author's box or call 313-462-0005.

Jan 7, 1988

Exploration of new resources and development of new equipment and designs are an ever changing facet of mining. New equipment to handle specialized operations is being developed and new techniques for its use explored. One such system is reviewed. Another is a potential system for handling the thinner stray coal seams between the more profitable thick seams. The availability of federal coal leases in the West is reviewed and current planning discussed. Gulf Coast lignites have been of much interest in recent months and are overviewed.

Jan 1, 1979

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By Dongjie Zhang, Fengyu Ren, Xudong Li, Yanjun Zhou, Yang Liu, Rongxing He, Jianli Cao

Based on the limiting-equilibrium analysis of roof processive caving in hanging wall caving method and the critical medium column theory, a new model of subsidence prediction caused by sublevel caving mining method was proposed in this study, considering the drawing influence and the dynamic process of filling granular media. Meanwhile, the distribution rules for lateral pressure with different orebody dip were studied under drawing ore, and subsequently complemented the model. This model indicated that the surface subsidence scope decreased as the unit weight of crack rock and the orebody dip increased. In addition, the height of critical medium column showed a decreasing trend as cohesion of rock mass, the internal friction angle and the unit weight of rock mass. Also, the method of predicting the scope of surface subsidence in the Dabeishan Iron Mine was applied. The results showed that the relative errors are less than 9% and the prediction method could be used in practical application.

Feb 24, 2022

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By L. Thompsen

High-pressure grinding rolls (HPGR) offer capacity increases, savings in operating costs and metallurgical advantages. The first installation of the Polycom HPGR in a copper ore treatment plant occurred in July 1995 at Cyprus Sierrita’s mining complex near Green Valley, AZ (Fig. 1). Until that time, the benefits this technology offers for copper and gold ore were only demonstrated on testwork. In other industries, such as diamonds, HPGR have proven to be reliable in industrial-scale plants and have set a new standard for this kind of ore treatment plant. HPGR are also successfully used for the comminution of coal, blast furnace slag and in cement and pelletizing plants. The installation at the Cyprus Sierrita Mine should prove the economical benefits in commerical-scale copper mining, confirming the results of comprehensive testwork(Fig. 2).

Jan 1, 1996

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device. Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery. Recent developments-in electrooptic inspection of dry end wet material leaving a grinding device are critically reviewed. New methods for characterizing ultrafines are discussed. A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine index and other fineness indices is described.

Jan 1, 1983

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer's machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

By J. D. Cooper, D. W. Thompson, J. Basiuk, W. Cass, R. Ilves

The Department of Thoracic Surgery and Pathology at the Toronto General Hospital have had a long standing interest in the early detection and treatment of carcinoma of the lung. Our initial experience was with a population at risk due to a prolonged period of cigarette smoking. More recently our efforts have turned to industrial exposure, specifically in the nickel and uranium industries. [Initial Screening Project] (1) For a three year period 1963 to 1966 a cytology screening program was carried out through the Out-Patient Department. The study was limited to cigarette smokers over 40 in age. A total of 1586 patients were examined. Of the sputa collected, the classification is seen in Table 1. There were 11 malignant sputa present. Added to this number were 25 patients with symptoms, normal chest X-rays, but malignant cells on cytology, and a further 5 patients in whom an abnormality (eventually proven non-malignant) showed on X-ray, and sputum showed malignancy which was radio logically occult. (Table II). This gave a total of 41 patients with malignant sputum who were evaluated between 1960 and 1966. The clinical course of these patients is seen in Table III. Only 19 of 41 patients had localization and treatment of their tumour during that study period and this low rate of localization attests to the technical difficulties endoscopy in that day presented. The method of localization was as follows: a) 6 patients showed an area of segmental pneumonitis somewhere in this time period b) Using the rigid bronchoscope localized the tumour in 9. This was proven by direct biopsy, and frequently required more than one bronchoscopy over a prolonged time period. c) bronchograms and tomograms showed abnormalities in 5 patients. Of these 19 patients, 5 were treated by radiotherapy because of general condition or refusal of surgery. Three of the irradiated patients died of recurrent cancer within three years. The other two died within one year of unrelated disease. Fourteen patients underwent resection, with one operative mortality. At pathology, the tumours were "in situ" in 6 and invasive in 13. There was no evidence of nodal spread. When last followed up in 1979, there were no cases of recurrent tumour and no cases of second lung primary tumours. Similar experiences have been reported from the Mayo Clinic (2), Johns Hopkins (3) and Memorial Hospitals (4). Early detection of radiologically occult tumours which are in situ or minimally invasive has given uniformly good results. There have been no deaths from recurrent or metastatic cancer in surgically resected patients, and only one second primary tumour has been detected. Interestingly, the Hopkins group reports that 5 patients with Stage I squamous cell tumours refused operation. One refused any treatment and died of disease at 12 months. Three were radiated, and were alive from 14-38 months post-treatment, all with evidence of recurrent disease. [Sudbury Sintering Plant Study](5) From 1948 to 1963 an open travelling-grate sintering process was employed to convert nickel sulfide to nickel oxide at an International Nickel Company operation. The environment in this plant was particularly dusty and filled with fumes. It became apparent by 1969 that the incidence of bronchogenic carcinoma was markedly increased in workers from this plant. A concerted effort was made to track down all workmen with this exposure. During 1973 and 1974, 268 men were studied. Chest radiographs were done and showed no mass lesions. Sputum was collected on three consecutive days and analyzed. There were 12 men with malignant sputum, all of the squamous cell variety. Two refused any investigation, one presenting 31/2 years later with extensive hronchogenic carcinoma, and the other 5 years later with extensive carcinoma of the maxillary sinus. In the remaining ten patients careful rhinolaryngeal examination as well as a detailed bronchoscopy, involving examination, brushings and biopsy of all pulmonary segments was carried out. One patient was found to have laryngeal carcinoma and was treated by radiation. In nine patients, the malignancy was localized to the lung, leading to six lobectomies, two pneumonectomies and one sleeve lobectomy at operation. However, the follow-up in these cases suggests a different biological behaviour with these industrially related tumours. While no tumour has recurred locally, one patient has died of metastatic cancer and two patients have developed second and one patient a third pulmonary primary cancer. However, survival has still been much better than wits radiographically manifest lung cancer. [Technique of Localization] (6) Following a careful rhinolaryngeal examina examined and then the lower respiratory tract is examined. This is all performed under general anaesthesia. The trachea is examined with the rigid Jackson bronchoscope, collect-

Jan 1, 1981