Search Documents

By John W. Kopp

The U. S. Bureau of Mines investigated flyrock and burden movement from blasting at several limestone and basalt quarries in the upper midwest. Blasts have been studied at 14 different sites using high-speed cinematography. Blasting was accomplished in 75- and 150-mmdiameter holes using a variety of explosives. Films from each blast were analyzed to show burden velocities, observed flyrock distance, and direction of throw in relation to the shot layout. This technique, in some cases, allowed determining point of origin and cause of the flyrock as well as the flyrock range.

Jan 1, 1994

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By Thomas M. Keevin, Gregory L. Hempen

Natural resource agencies, under various regulatory authorities, are challenged with permitting underwater explosive use while at the same time protecting aquatic resources. Deciding on whether or not to allow use of explosives requires striking a balance between development and aquatic resource protection. A company's goal in underwater explosive use is to select methods that are both expedient and cost effective. Use of explosives is often the best alternative for engineering reasons or economic considerations. Over and above legal requirements, indiscriminate destruction of fish and other aquatic resources is not in a company's best interests because of concerns relating to public image, as well as the need to secure future contracts.

Jan 1, 1995

By Jianjun Tang, Wenjuan Bai

This paper presents a new method of formulation design for multi-component composite explosives. Based on the thermochemistry of the detonation process, the mathematic model of formulation design is established by optimization mathematics. Using the heat of detonation as target functions and taking the constraint conditions such as oxygen balance and costs etc into consideration, this model can provide an optimal solution quickly by means of personal computer. Using this method, the calculation and the simulation tests for a series of constituent sets and various constraint conditions can be conducted easily. In this way, the optimal formulation for the explosive can be determined, on the basis of the maximum heat of detonation and the lower cost.

Jan 1, 1997

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987

By Leslie Taylor, W. Fourney, Uli Leiste

This paper presents the results from a series of tests conducted to investigate the total vertical impulse delivered to a target plate by a buried explosive charge. The tests were conducted at a very small scale but previous work has shown that small scale testing can predict impulse applied to plates in full scale. Non-deforming plates were used to determine the change in impulse delivered to targets as a result of changes in standoff distance and burial depth changes.

Jan 1, 2009

By Dale Nies

In the past, cap and fuse has been the only economical and efficient initiation system capable of providing sequential timing, ease of loading and hookup, and unlimited borehole number for backstope rounds. Unfortunately, in spite of these advantages, several negative factors inherent to the system have always been noted. Due to the long, narrow nature of backstope rounds at the Sunshine Mine, the cap and fuse system results in very long, inaccurate delay times. The system was also occasionally unreliable under all the conditions encountered, which in turn could cause potential safety hazards.

Jan 1, 1989

Introduce self – thanks for having me.Indiana program – spent first 15 years of program telling folks how smart we are and to trust us. “We are from the government and we are here to help you.” How well would that go over with you if the IRS invited you in for an audit and that was their openning? Our audience was the same way – not thrilled or inspired. We decided we were the problem – being nice guys just was not enough. We had to learn to communicate with people who did not know us. I am here to share a few things we have learned – and are still learning.

Jan 1, 2007

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

By Robert E. Miller

Mass blasting of open stopes and pillars is a normal operating practice at Isa Mine. Three main parameters are used to classify the types of mass blasts. These are type of explosive used, blasthole diameter and system of initiation. Both electric and non-electric initiating systems are currently employed. The advantages gained by large firings are many. More efficient utilization of manpower, due to the concentrated and continuous charging, is achieved. There is no requirement for men to re-enter areas where localised ground conditions may have deteriorated and exposure of ringfirers to stope voids is reduced.

Jan 1, 1980

By Zhao Jie, Christopher G. Smith

Commercial explosive use in China has been dominated by powdered AN-TNT mixes. Water gels and emulsions are now gaining market acceptance because they offer potential for better performance. Although raw material costs for emulsions initially may be more than AN-TNT mixes, the more expensive technology improves sensitization and leads to lower costs overall for mining operations. A recently completed study in northeast China compared microsphere-modified emulsions to AN-TNT and lower-cost emulsions. Testing of microsphere-modified emulsions at several pH levels indicated a high degree of stability and consistency of VOD. Using 42 mm blastholes in underground mines and 170 mm holes in sandstone open pit mining demonstrated the superior performance of glass microsphere sensitized emulsions. Comparisons of explosive cost, drilling cost, secondary blasting cost and muck pile profile were favorable to the microspheres-sensitized-emulsions. Noxious fumes with AN-TNT or with water-based systems that partially fail during detonation are also a concern. Efficient detonation of emulsion products sensitized with hollow spheres appears to reduce fume generation. Prolonged storage or exposure to water also is not a problem.

Jan 1, 1997

By Lewis L. Oriard

The purpose of this paper is to provide an overview of close-in blasting effects on various types of structures and building materials, as encountered in this writer's professional practice. Structures range from old, deteriorated historical monuments to new, heavily reinforced buildings. Materials range from clay adobe to concrete and steel. Site locations range from tropical to arctic. Blasting ranges from sculpture blasting inside buildings to "coyote" blasting and large surface blasting operations. Space limitations permit a brief discussion of only 25-30 specific cases, but they have been selected to be typical of conditions found on hundreds of similar cases. The writer was asked to present a discussion of representative cases where relatively high vibration intensities were experienced. Virtually all of these cases were free of damage, but the few damage cases provide valuable insight to the mechanisms involved. Observations of such damage and non-damage cases have served as the basis of this writer's criteria for various structures and materials, as well as the technology to conduct blasting operations within those criteria. A sampling of these experiences is gladly shared with the reader.

Jan 1, 1991

Vibrations are of concern not only for the safety of surface structures but also for the stability of underground openings. A number of parameters affect the intensity of vibration in underground openings due to blasting in adjacent opencast mine viz. total explosive weight detonated in a round, maximum explosive weight per delay, propagating media, depth of cover, RMR of the roof rock, age of the underground openings etc. Although a few researchers have tried to study the impact of parameters stated above, the impact of initiation sequences on generation of vibration in underground openings due to opencast blasting has yet remained untouched. A study was planned to evaluate the impact of initiation sequences on the magnitude of vibration in underground openings due to blasting in opencast mine. Nine production blasts with top and bottom initiations were performed at Samleshwari opencast project in India and eighteen vibration data were monitored in the roof of Hingir Rampur underground colliery in both the initiation sequences. The result indicated that the vibration produced in the underground openings from bottom initiation was lower than that of top initiation.

Jan 1, 2003

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow, VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

Jan 1, 2004

By TA Louw, Dr CM Lownds

In an era where profits are constantly being eroded, mines are looking towards technology developments to assist them in solving mining problems and reducing mining costs. An emerging technology that could assist mines in becoming more cost effective is electronic detonators. Electronic detonators have been under development for several years. Over the past three years, the spotlight has fallen on commercial use of electronic detonators and the extent to which the promise of precise and programmable timing can assist mines with their environmental and productivity problems. This paper uses case studies to demonstrate both surface and underground applications where electronic detonators and blasting systems were used to solve typical mining problems such as vibration and fragmentation. Safety aspects such as hanging wall conditions and high wall stability also benefited from the use of electronic detonators. The paper also demonstrates how the use of accurate electronic detonators and blasting systems has resulted in improved/more even fragmentation with further downstream efficiencies. These efficiencies may include increased cast percentages, reduced oversized rocks, quicker cleaning times and increased production rates.

Jan 1, 2004

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Savas Gorgun

The principal disturbances created by blasting in open pit mines are vibrations, air blast and fly rock. All of them, under some circumstances, caused damage to structures nearby and apart from this can be the source of permanent conflict with the inhabitations who live close to the operation. Therefore, prediction of ground vibration components is of great importance for the minimisation of the environmental complaints. This paper presents the result of ground vibration measurements induced by bench blasting realised at Can Open Pit Coal Mine located close to the residential area of Can town. Within the scope of this study, in order to predict peak particle velocity and determine the slope of the attenuation curve for this site, ground vibration components were measured for blast events during bench blast optimisation studies over a long period. During the study, while the parameters of scaled distance were recorded carefully, the ground vibration components were measured by means of two different types vibration monitors (White Mini-Seis and Instantel Minimate Plus Model) for 54 blast events. At the end of evaluation an empirical relationship with reasonable correlation was established between peak particle velocity and scaled distance for this site.

Jan 1, 2001

By Lawrence Mirabelli, Wayne Lidkea, Mario Paventi

On Januarv 1, 1996, INCO Limited, Tamrock OY, Dyno Nobel and CANMET formed a consortium for the development of robotic mining equipment called the Mining Automation Program (MAP). This project was a tive- [5] year research and development program that combined the talents of the above organizations to facilitate the development of mining equipment and systems for tele-remote mining. The year 2000 brings MAP to conclusion with actual production process trial testing of the developed prototype equipment and systems during the period between May and October. MAP consisted of multiple projects all of which are based on the communication system developed by INCO Mines Research and currently sold and marketed by Automated Mining Systems Limited. The main projects include the development of a positioning and navigation module (including a software mapping system that will be inherent to each piece of equipment), robotic systems for underground development and stoping operations, as well as software systems to support the use of this equipment. Included in the program was the establishment of a Research Mine, at INCO’s 175 orebody, Copper Cliff, Ontario, Canada. This facility allowed for the on-site collaboration between the companies and research organization in the design and testing of techniques and equipment to mine with TeleminingTM. Some of the prototype equipment developed through the program are: a tele-operated drilling jumbo, a tele-operated load-haul-and-dump [LHD] tram, a tele-operated production drill, a remote initiation system for programming and detonation of electronic detonators, and the development of a vatiable energy bulk emulsion explosive system, including loading equipment, to deliver the explosives to boreholes. Use of tele-operated and automated equipment for mining mandates a dramatic change in the traditional drill/blast/muck/support cycles in the underground mining process.

Jan 1, 2001

By NA NA

None

Feb 6, 2023

By Walter Voglauer, Elisabeth Zechmeister

Description of Project: The four photos show a chimney blasting operation in Vienna’s district of Floridsdorf on May 4 2011. The blasting was done with two types of charges. An internal charge provided a force of blast which resulted in 135 single electrical blasting caps initiated detonations on the basic ensured the straight collapse of the chimney. The preparation work was done by reserve force military engineers. The series of photos were shot by Elisabeth Zechmeister. She works in the Austrian DOD but not as a professional photographer; much more she did all activities in her spare time.

Jan 1, 2013