Search Documents

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

By Mitchell P. Rothman

This paper concentrates on profits and other measures of return in the Canadian mining industry, especially in the non-mineral-fuels sector. The paper examines the historical patterns of mining profits, both before and after taxes, as compared with profits in other sectors of the Canadian economy, as well as some of the more important influences on mining profits. These include the prices of mineral products, provincial and federal tax policies with respect to mining , and the effect of inflation on mining profits and the financial position of mining firms - in each case, comparing mining with the other sectors of the economy. Finally, the paper provides an analysis of current and prospective rates of mining profits in relation to the capital required to ensure the future viability of the Canadian mining industry.

Jan 1, 1977

By Xu Feng, Han Shufeng, Zhu Bin, Wang Mingming

Due to urban subway tunnels mostly built in the cities with highly density buildings, the geological and construction conditions is complex, especially certain sections of the subway tunnel will pass through from the foundation of the overpass, therefore the stability and surface deformation control of that section’s tunnel excavation is particularly important. Taking Xi'an Metro Line Three interval tunnel as a research object, we have used FLAC3D simulation to analyze the tunnel’s surrounding soil deformation and tunnel lining stress distribution under bridge foundation with shallow buried covered excavation method. Analysis results show: (1) After the excavation of the tunnel right line, due to the bias of the upper bridge foundation the right of the tunnel showed relatively large deformation. In order to ensure the construction safety, we recommended using the grouting anchor reinforcement on the right side wall to further control the deformation zone. (2) The maximum vertical displacement of the ground occurred in the right wall of the tunnel portion which was due to the intensity of soil outside the grouting range of the arch is low, as a result the deformation is larger; this position requires special attention, strengthening the monitoring measurements of this part is necessary to avoid the large deformation and other adverse effects of the upper portion of bridge foundation. (3) The maximum vertical force area of the initial lining of the tunnel is in the middle of the side wall, while the second lining in this part of forces is smaller, thus at the beginning of the construction of the liner, attention should be paid to this area. On-site grouting or steel bracing reinforce support may be used if necessary.

Jan 1, 2015

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By M. Narita, S. Nakayama, M. Fujihara

Hibi Kyodo Smelting Co., Ltd. was founded in 1968 and celebrated its 50th anniversary in 2018. In 1972, we started producing copper cathode with a production capacity of 84 KTPY. Since the company founding, we have undertaken seven expansion projects, and our current copper-cathode production capacity is 290 KTPY. To increase our production efficiency, two tank houses were converted from Conventional process to ISA process in 2006 and 2014. In another investment, we equipped a continuous glue dosing system, which allowed for strict additive-concentration control, yielded quality improvements and reduced the power-consumption rate. Along with an increase in the production of copper cathode, the amount of impurities eluted from the anode increases. To solve this problem, the chelate-resin purification process that was introduced in 1983 was renovated, and impurities could be recovered more efficiently. In this paper, we report various improvements that have been implemented at the refinery since 2000. INTRODUCTION Tamano Smelter and Refinery of Hibi Kyodo Smelting Co., Ltd., founded in 1968, celebrated the 50th anniversary of its founding in 2018. The Tamano Smelter opened its No. 1 tankhouse in 1972, and began operating No. 2 tankhouse in 1984. Thereafter, with continuous production increases and technical improvements, electrolytic copper production was increased from 84 KTPY to 290 KTPY as shown in Figure 1. Table 1 shows the major operating facilities and operation data in 2017.In this paper, details of equipment introduced to continuously dissolve and add glue, various improvements made to the chelate resin process, enhancements made to the crude Ni sulfate process, and another vibrating screen introduced to the copper slime processing flow in accordance with the expansion of copper production capacity since 2000 are reported.

Jan 1, 2019

By M. L. Trépanier

"Engineering and technical services are supplied by the Engineering Department, located at Thetford Mines, Quebec, approximately 60 miles southwest of Quebec City. The department serves the three operating mines in the Thetford area, the Asbestos Hill mine at Putuniq, Nouveau Quebec, and the Nordenham plant at Nordenham, West Germany. The Engineering Department is responsible for supplying the following services. 1. Administration and coordination of capital projects. 2. Engineering, design and drafting services for in-plant changes or improvements. 3. Preparation of geological plans for mine planning and ore reserves determinations. 4. Short-, medium- and long-term mining plans. 5. Rock mechanics studies and monitoring. 6. Grade control monitoring. 7. Environmental control engineering and construction. Details of the organization and services rendered will be the basis of the paper."

Jan 1, 1976

By Giles St. Pierre

"The purpose of this paper is to report in a general way on the use of the Portaspec X Ray Spectrograph.At Manitou Barvue, we are milling two types of ores, copper and zinc. The control assay practice was to take grab samples at 4 hour intervals. These samples were dried in the mill, then taken over to the Assay Office where two operators would process them. Three hours later results were available at almost the same time as the operator was ready to take his set of grabs again, leaving no time for adjustments, if any were needed.After a reduction of personnel, there were no assays available on night shift. This practice was slow and inadequate, and a new way of doing control assays was investigated.After investigation the Portaspec was found suitable for the type of operation that we had in mind. The Portaspec is a conventional dispersive type of X Ray spectrograph. The instrument consists of three parts:The Power Supply The Spectrographic Head The Digital ScalerIn our case, where dried powder samples are analyzed, the instrument was provided with a two sample holder using one for the standard and the other for the sample. The operation of the instrment does not require any degree of skill or knowledge of chemistry or spectrography.Previous to buying the instrument, six sets of six to ten samples were sent to the supplier along with the assay for each sample. These samples were Cu. HDS., Cu. Conc., Cu. tls, - Zn. HDS., Zn. Conc., Zn. tls. A definite pattern was observed. For example - six Cu. HDS. samples ranging from .40 to .90 gave 10400 counts for the lowest to 16.040 counts for the highest. The number of counts were then plotted to give percentages."

Jan 1, 1971

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By J. W. Griffith

"The mines in the Bancroft area of southeastern Ontario, a few kilometres west of the town of Bancroft, are in Faraday and Cardiff Townships. Three companies, known as Canadian Dyno Mines Limited, Macassa Gold Mines Limited (Bicroft Division) and Madawaska Mines Limited (formerly Faraday Uranium Mines Limited), with plants capable of handling a total of 4,()()() tons (3,629 tonnes) of ore a day, were at one time in production. A fourth company, Greyhawk Uranium Mines Limited, operated a small mine whose ore was shipped for custom treatment to the nearby Faraday mill. Canadian Dyno Mines Limited ceased operations in June 1960. In June 1963 the Bicroft Mine was closed and a year later Faraday closed because of contract completion. But in 1975, Faraday (now called Madawaska) was re-opened but closed again in 1982. During 1959, the peak year, these four mines produced an estimated 1,100 tons (998 tonnes) of uranium precipitates, which represented nearly 7 per cent of Canada's output for that year(Fig. 1).The deposits occur in pegmatitic granite dykes in a region of high-grade metamorphic and metasomatic rocks. Uranium distribution is usually controlled by the distribution of mafic minerals, particularly hematite and magnetite, and by late fractures. The best visual indicators for uranium concentration are hematite staining in the pegmatite, followed by the amount of mafic inclusions or crystals. The Bancroft area orebodies are the only known deposits of the general pegmatitic class in Canada that contained economic deposits of uranium. The principal radioactive minerals are uraninite and uranothorite. By comparison with many other pegmatitic occurrences, some of the ore bodies are unusually large, persistent in depth and relatively rich in uranium minerals. At the end of 1981, total ore reserves were estimated at 1,500,00 short tons (1,360, 000 tonnes) averaging 0.11 % U3O8."

Jan 1, 1986

By R. R. Culbert

Several thousand parts per billion of uranium are present in some alkaline lake and ground waters of the Okanagan region, British Columbia. To a major extent the uranium content of these highly anomalous waters is controlled by their levels of dissolved bicarbonate. In lakes, dissolved bicarbonate and the organic content of the sediment largely control the partitioning of uranium between sediment and water. This relationship is found to a lesser extent in alkaline creeks, and transported geochemical anomalies in soils appear where uranium-bearing alkaline ground waters have encountered organic materials. There is a possibility that young, near-surface deposits (with very low radioactivity) are forming from these uraniferous waters.

Jan 1, 1978

By R. J. Fruehan

Oxygen steelmaking (OSM) is not only the dominant steelmaking process but defines the structure of the industry. There are a number of myths regarding the future of OSM, which are false. These myths include that the EAF will become the dominant process in the near future, it is less costly to produce steel in an EAF and OSM is a mature technology and no new developments are occurring. These myths are shown to be false. Selected new developments are discussed such as post combustion, recycling of waste oxides, slag splashing and sensors.

Jan 1, 2004

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By P. Bonadia, A. Tabereaux

Nearly all aluminium smelters are increasing the potline amperage to achieve higher aluminium production. In some instances the higher amperage operation has a significant negative impact on shortening the lifetime of aluminum electrolysis cell cathodes due to loss of the protective sidewall cryolite ledge freeze and too rapid penetration of the cell bottom refractory lining by cryolitic bath components due to the higher temperature isotherms. Thus Cathodes require careful thermal modeling of the cathode relining designs and improved refractory materials to allow greater heat loss from the sidewall to preserve a stable sidewall ledge freeze at higher amperages, and the selection of optimum refractory barrier materials to control the penetration and reaction of bath into the cathode bottom refractory and insulation lining. This requires an understanding of the reaction mechanisms and product formation for molten NaF enriched bath and alumino-silicate refractories. It is desirable to use dense, low porosity refractory fireclay firebricks, or similar materials with a sufficiently high silica content to promote the formation the mineralogical phase albite, NaAlSi3O8, that significantly increases the viscosity of the melt which slows the diffusion of reactive species in the melt and thereby retards further bath penetration.

Jan 1, 2004

By S. E. Wolfe

The presence of helical ribs in smooth-bore round pipe results in the transport of granular solid particles m water at a much lower velocity than required to transport the same solids in a smooth pipe. The helical motion imparted to the flowing mixture effectively returns settled solid particles to the main stream. The flow may be stopped and restarted without difficulty. Due to the lower velocity required for satisfactory transport large power savings are realized. Also: due to lower velocity, the wear on the pipe walls is much reduced. For satisfactory performance, the ribs should have a high angle relative to the long axis of the pipe and the lineal spacing between adjacent ribs should be modest.

Jan 1, 1967

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004