Search Documents

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By G. Gutierrez, D. A. Elgillani, M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. In this article, the flotation responses of these minerals in the presence of potassium oleate and sodium silicate are described and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium-bearing minerals such as fluorite from calcite1-3 and scheelite from calcite2,4 and apatite,2,5 for example, almost always involve the use of sodium silicate. The mechanisms by which sodium silicate functions as a depressant are still not understood, probably for a number of reasons. For one thing, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species.' Moreover, the type and concentration of these species depend on the ratio of Na2O to SiO2, the concentration of sodium silicate, and the pH of the system.' At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant. EXPERIMENTAL MATERIALS AND METHODS Pure samples of apatite (Durango), calcite (Iceland-spar), fluorite, and scheelite were used in this investigation. Pure potassium oleate was used as collector, while reagent-grade HC1 and KOH were employed for pH adjustment. The sodium silicates used were samples obtained from the Philadelphia Quartz Co. In one series of experiments, various sodium silicates containing different ratios of SiO2 to Na2O were added to calcite systems. These sodium silicates contained SiO2-to-Na2O ratios of 3.75 to 1, 3.22 to 1, 2.40 to 1, and 1.60 to 1. All other experiments were conducted with the sodium silicate containing the ratio of 3.22 to 1, which is the one that is normally used in industry. Flotation experiments were conducted with 21/2-g charges of 48 x 150-mesh material in conductivity water with an apparatus and technique described previously. Electrokinetic experiments were conducted with both a Zeta Meter and streaming potential apparatus. Particle size was 48 x 65 mesh for the streaming potential experiments. EXPERIMENTAL RESULTS The first series of experiments involved flotation of scheelite in the absence and presence of sodium silicate. As shown in Fig. 1, flotation response was not affected with even the relatively high addition of 1 x 10-3 mole per liter sodium silicate. Interestingly though, no flotation was effected below pH 6 with this collector addition. The responses of apatite to flotation under these same conditions are given in Fig. 2. Similarly, no depression was obtained in basic media under these conditions. Similar experiments were conducted with fluorite, and in this case, depression was noted above about pH 11 with 1 x 10-3 mole per liter sodium silicate (Fig. 3). When calcite was floated with these same levels of addition of sodium silicate, essentially no flotation was possible above pH 7 (Fig. 4). The effect of collector addition with a constant addition of sodium

Jan 1, 1969

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By J. H. Brophy, S. J. Michalik

A constitution diagram for the system Mo-Ir has been determined. The maximum solubility of iridium in molybdenum is 16 at. pct at 2110ºC and decreases to less than 5 at. pct at 1500°C. The solubility of molybdenum in iridium is 22 at. pct. Three intermediate phases appear in the system: 8 MoJr, having the p-tungsten structure; a phase, a cornplex tetragonal structure; and the hcp ? phase. Metallography, melting point determinations, X-ray diffraction and fluorescence, and electron micro-probe unalyses were employed in establishing the diagram. PREVIOUS to the present investigation, the intermediate phases in the Mo-Ir system were identified, but no detailed account of the phase diagram has been reported in the literature. Raub1 investigated alloys of Mo-Ir over an extensive range of composition between the temperatures of 800º and 1600°C. The in-termetallic compound MosIr was found to exist with nearly pure molybdenum, as the solubility of iridium in molybdenum was not detectable parametrically in this temperature range. MO3Ir was found to be iso-morphic with a ß-tungsten type structure, having a parameter of 4.959Å. An intermediate hcp phase, designated as the ? phase, ranged in composition from 52 to 78.5 at. pct at 800ºC, and from 41 to 78.5 at. pct Ir at 1200°C. Parameters noted for the ? phase were as follows: at 42.7 at. pct Ir, a = 2.771i0, c = 4.4366, c/a = 1.601; at 78.5 at. pct Ir, a = 2.736A, c = 4.378A, c/a = 1.600. Molybdenum was found to be soluble in iridium up to 16.5 at. pct Mo (83.5 at. pct Irj, with the parameter of iridium increasing to 3.845A at the solubility limit. Knapton,2 who investigated alloys between 15 and 85 at. pct Ir, essentially agreed with Raub's data, but, in addition, found a a phase in as-melted alloys near 25 at. pcto Ir. The oaphase lattice parameters were a = 9.64Å, c = 4.96Å, c/a = 0.515. The a phase was replaced by the 8 -tungsten phase on annealing at 1600°C. Knapton concluded that the a was stable only at elevated temperatures, and placed the composition of the a phase at approximately 30 at. pct Ir. The intermetallic compound Mo3Ir, with a lattice parameter of 4.965A, was included among the 8-tungsten structures reported by ~eller.' Matthias and Corenzwit,4 and Bucke15 studied the superconducting nature of MosIr, and reported a superconducting transition temperature of 8.$K. The present investigation describes the phase relationships in the Mo-Ir alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURES Alloys for the determination of the phase diagram were prepared from powders. Commercial 99.9 pct Mo from Fansteel Metallurgical Corp. and 99.9 pct Ir powder from J. Bishop and Co. Platinum Works were used. The powders were weighed to nominal compositions, mixed, and then pressed, without binder, into compacts weighing 4 to 6 g. These were presintered in uacuo between 1200' and 1400°C for 1 hr, to reduce the degree of spattering during subsequent arc-melting. The compacts were arc-melted in a nonconsumable tungsten electrode furnace six times on alternate sides on a water-cooled copper hearth in an atmosphere of zirconium-getter ed argon at 500 mm of mercury pressure. In almost all cases, this procedure yielded buttons of satisfactory homogeneity. The composition of all melted buttons were confirmed by X-ray fluorescent analysis using the experimentally determined ratio of the iridium La1 line intensity to that of the molybdenum Ka1 line as a function of composition. In this determination four alloys analyzed by wet chemical methods were used as standards. An uncertainty range of ±1 at. pct has been attributed to all indicated compositions. All heat treatments and solidus measurements were carried out in tantalum resistance heating elements in vacuum conditions of 10-4 to 10-5 mm of mercury. A detailed account of this procedure has been reported by Schwarzkopf and Brophy.8 In the heat treatment and solidus measurements of iridium-rich alloys (50 at. pct Ir or greater), a tungsten lining was inserted into the tantalum resistance heating element because of a eutectic reaction which occurs between iridium and tantalum at 1948ºc.7 Heat treatments and solidus measurements carried out at compositions less than 40 at. pct Ir both with and without tungsten linings within the resistance

Jan 1, 1963

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By Andrew Corry

GEOPHYSICAL investigations based on radioactivity have been applied to the earth's crust for the purpose of discovering bodies rich in radioactive substances, or for the location of solutions with high emanation or radioactive-salt content, or for the detection of oil, which, in virtue of colloidal properties, has strong powers of radioactive absorption. RADIOACTIVE SUBSTANCES Radioactive substances are distributed in all rocks, waters, and gases in the earth's crust in small quantities. Granites and similar acidic rocks are richest in uranium and thorium, two chief radioactive substances; yet the quantities present in such rocks are of the order 10-12g., this concentration being expressed in grams per gram of the whole substance per cubic centimeter. In granites the uranium yields, according to Haddock, 3 X 10-12 g. of radium per gram of rock. In basalts the uranium yields 1.19 X 10-12 g. per gram per cubic centimeter. Of thorium the granites yield -2 X 10-5 g. per gram of rock; the basalts, 0.77 X 10-5 g. per gram. Certain series of alkalis of low atomic weight, like potassium and rubidium, show weak radioactivity; this property has no significance so far for geological research. The uranium is esti-mated indirectly from the electrical properties of one of its derivatives as a -gas (emanation) into which it is transformed. The thorium is expressed directly, though it is measured as a derivative, thorium emana-tion. There is a measure for the gaseous radium emanation, the curie, which is that quantity of radium emanation, or radon, which stands in equilibrium with 1 g. of radium. The concentration of the emanation is the Mache unit corresponding to 3.64 X 10-10 curie per liter. When gases become permeated by alpha, beta, and gamma rays, plus and minus ions are produced in them by the decomposition of neutral gas molecules, and under the influence of an electrical field these ions are given opposite motions. The measurement of the alpha rays and the bisection thicknesses of the beta and gamma rays is a means of analyzing unknown radioactive substances. These rays accompany the disintegration of radioactive substances and arise from "spontaneous internal changes

Jan 1, 1929

By Jasper Johnson

Taken in all its bearings there is, perhaps, no more interesting coal-field than that locally known and designated as " Wilmington," both on account of the superior qualities of its product as a household and steam fuel, when compared with other Illinois coal, and its geological position. The territory underlaid with coal, to which this name was originally given, embraced a very small area, including only the south half of sections 31 and 32 (township 33 north, range 9 east) in Wilmington township, and sections 5, 6, 7, 8, 17, 18, 19, 30, and 31, with occasional outliers in sections 3, 4, and 9, and, possibly, in sections 20, 28, 29, 30, and 32 (township 32 north, range 9 east) of Reed township, in Will County, comprising eleven square miles of workable coal within the known basin. Borings indicate the presence of coal on sections 30 and 33 in Wilmington

By Jasper Johnson

TAKEN in all its bearings there is, perhaps, no more interesting coal-field than that locally known and designated as " Wilmington," both on account of the superior qualities of its product as a house- hold and steam fuel, when compared with other Illinois coal, and its geological position. The territory underlaid with coal, to which this name was originally given, embraced a very small area, including only the south half of sections 31 and 32 (township 33 north, range 9 east) in Wilmington township, and sections 5, 6, 7, 8, 17, 18, 19, 30, and 31, with occasional outliers in sections 3, 4, and 9, and, possibly, in sections 20, 28, 29,30, and 32 (township 32 north, range 9 east) of Reed township, in Will County, comprising eleven square miles of workable coal within the known basin. Borings indicate the presence of coal on sections 30 and 33 in Wilmington

Jan 1, 1875

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"&apos; was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.&apos; In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

By W. D. Forgeng, B. F. Decker

IT has been known for almost a century&apos; that silicon and nitrogen combine when heated to a high temperature. Three nitrides have been reported, SiN, Si3N,, and Si,N, containing 33.3, 40.0 and 42.9 pct nitrogen by weight, respectively. The existence of SisN, is well established but that of Si,N, and SiN is doubtful. The first systematic study of the reaction between silicon and nitrogen was made in 1910 by Weiss and Engelhart" who determined the rate at which silicon absorbed nitrogen at temperatures from 1250°C to

Jan 1, 1959

By F. F. Aplan

Pollution control will be of utmost importance in the 1970&apos;s. In this area, the mineral process engineer has a special competence to understand and remedy many pollution situations. There is an old adage that goes, "Build a better mouse- trap and the world will beat a path to your door." Would that it were so, but the reality of the situation is such that, just as a supplier must sell his machine, a professional man must sell his competence. It is a sad but true fact that mineral processing engineers have not done a very good job in selling their extensive competence in the control of a broad range of pollution problems. Recently one of our students visited a paper pulp mill where he was shown a foam fractionator used to remove paper pulp fibers from plant discharge waters. "Foam fractionator hell, that&apos;s a flotation cell!&apos;&apos; was his comment. Ah so, it would appear that large numbers of technical people consider themselves experts on "foam fractionation" Or is it that we have been very remiss in demonstrating the usefulness of our equipment and processes and our professional competence to solve, these pollution problems?

Jan 1, 1970

By Francis A. Thomson

T HE engineer of today is by his training, by his traditions, and by the service which he must render, irrevocably committed to taking his part in public life along with the members of the older professions of ministry, medicine and law. Nevertheless, in comparison with these: three, so long recognized as the "learned professions-all three of which grew out of the functions of the priesthood-engineering in any modern sense of the word is a youthful profession indeed. So youthful is engineering in its present significance, that it may be said to date from the labors of John Smeaton, the lighthouse builder; of Simon Newcomen and James Watt, the inventors of the steam engine; and of George Stephenson, the inventor of the locomotive; at the dawn of the 19th century. Great works of an engineering character had, it is true, been executed long before this, but practically all of them had been rule-of-thumb enterprises, dependent upon a plethora of slave labor for their accomplishment. For illustration it is said that at Rio Tinto in the days of Hiram, king of Tyre, 40,000 men worked for a year to produce three tons of silver from the rich outcrop ore. Such an operation can scarcely be called an engineering enterprise, however, when we remember that a fourth of this number of men in these same mines, from which the richest ore was long ago extracted, produce at present over 100 tons of copper per day.

Jan 1, 1925

By C. F., Christopher

The purpose of any steel-making process is to convert the two raw materials iron and scrap into steel. The chemical analysis of the steel is set within certain limits which involve the physical proper- ties desired by the consumer. In addition to tensile properties a large number of other properties are at the present time desired, such as impact resistance, grain size regulation, specific degrees of hardenability, resistance to creep at high temperatures, resistance to expansion on heat treatment, the ability of the product to undergo extreme amounts of cold deformation without failure, and many other properties which are not directly related to the specified chemical analysis. Variations in many of the properties of plain-carbon steels are due to elements and compounds not included in the ordinary "five element"§ composition. Such variations result primarily from variations in oxidation of the metal in the furnace and from the deoxidation method employed. The steel-making problem therefore resolves itself into two distinct sections: (I) the elimination of certain elements from the charge (the iron and scrap entering the furnace) and the addition of materials to meet the chemical specifications for the heat; (2) the manipulation of the slag and metal and the process of deoxidation to give certain desired properties in the steel entirely apart from the chemical analysis specified. Each of &apos;these two ends must be attained

Jan 1, 1957

By D. E. Hartman, J. M. Roberts

A detailed study of the temperature dependence of the critical stress, TB . necessary to cause a damping loss of 1.41 x 10-6 g mm per mm3 in pre-strained magnesium single crystals has been carried out in the temperature range 82" to 320°K. Tb is found to be linearly related to the reciprocal of the ahsol~cte temperature in this temperature range. The temperature dependence of the anelastic limit, TA, defined as the stress necessary to form open unidirectional stress-cycle damping loops has been measured between 82" to 320°K. ta is found to be independent of temperature in this range. It is suggested that TA is determined by the stress necessary to activate Frank-Read dislocation NUMEROUS studies1-9 have been reported concerning the details of yielding and microstrain near and below the generally discussed macroscopic flow stress. The work of Kramer and coworkers10-13 is helpful in determining certain qualitative facts. concerning preyield phenomena. The absence of a stress-dependent delay time in annealed copper and aluminum single crystals between 83" and 298 suggests that the preyield mechanism is temperature-independent in this range. This is not sources. The temperature and stress dependence of the effective activation volume (Veff) has been measured in the damping-loop region in prestrained magnesium single crystals. The data suggests that Veff/kT is approximately constant, equal to 2 4.5 sq mm per g in the temperature range 130°to 298°K, and that Veff is almost independent of stress at stress levels greater than 10 g per sq mm. A restricted model is developed to predict the stress (rb) necessary to cause a small fixed damping loss as a function of temperature, effective activation volume, and dislocation density. Various possible dislocation mechanisms controlling TB are discussed. true for zinc, p brass, and iron crystals in the same temperature range, however, since the existence of a stress-dependent delay time suggests a thermally activated preyield mechanism in these materials.10-13 The work by Vreeland et a1.14 confirms the work by Liu et al.ll on delayed yielding in zinc single crystals. A stress-dependent delay time between 82" and 298°K was found12 in prestrained aluminum and copper crystals. These results suggest that the preyield phenomena may be different between prestrained and unstrained or annealed crystals. The temperature dependence of the yield point at 2 x 10-8 plastic strain found by Rosenfield and Averbach3 in annealed copper and aluminum is not in agreement with the delay-time data, unless possibly the delayed yielding experiment only de-

Jan 1, 1964

By G. Barbery

Since the original paper, two methods have been introduced to compute the parameters of the three parameter size distribution equation: [ ] Both of them are based on graphical means, which are time-consuming and of little statistical significance. A program has been developed, using the Gauss-Newton method to compute by nonlinear regression analysis the parameters of the equation. Although the method is quite general in curve-fitting applications, it does not appear to be used in the field of size analysis, and a brief description is given. As applied here, the Gauss-Newton method involves the minimization of the least squares: [ ] where n is the number of sieves used. The second member of Eq. 2 can be approximated by a multiple Taylor&apos;s series expansion of first order about a starting value [ ] The minimization of Q (r,s,Xo) means: [ ] Putting Eq. 3 into Eq. 2 and differentiating, we obtain a system of equations which can be represented in matrix symbolism (box) The system can be solved for: [ ] and the operations repeated with new values: [ ] The starting values for r and s are taken as 1, for Xo, a value higher than the maximum sieve opening value. Applied to the data given by Herbst 5,6 for batch grinding of 7 X 9 mesh dolomite, the parameters given in Table 1 were obtained. The discussion of the significance of the residual sum of squares is a difficult subject in multiple nonlinear

Jan 1, 1972

By Philip B. Bucky

WITH the exhaustion of the sections of iron ore bodies amenable to opencut mining the iron ore miners raise the question: "How can we mine the extensions of these ore bodies in depth with the same costs as obtained in opencut work?" This question brings to the fore the relationship between mineral exploration and research on mining procedures. The iron miners must either find new de? posits amenable to their known methods of mining or develop new mining methods for deep deposits. It is understood that the oil companies will spend $30,000,000 next year in the search for new oil fields. How much the metal mining companies will spend in the search for new ore bodies is unknown, but without doubt the amount will run into several millions of dollars. If the mining companies that concern themselves with metals, nonmetallics, and fuels will set aside a substantial sum for fundamental and applied research in mining methods, they can not only lower their costs but increase their reserves thereby. Any increases in mining efficiency automatically result in increased ore reserves at no cost.

Jan 1, 1947