Search Documents

By G. E. Steudel

The study of the possibility of effecting a lower cost in the manufacture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the consideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improvements, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph,5 whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality. Large slag volumes result in higher coke consumption and cost of disposal. Any attempt to lower slag quantity must be accomplished

Jan 1, 1940

By G. E. Steudel

The study of the possibility of effecting a lower cost in the manufacture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the consideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improvements, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph,5 whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality. Large slag volumes result in higher coke consumption and cost of disposal. Any attempt to lower slag quantity must be accomplished

Jan 1, 1940

By J. F. Mitchell, R. Bainbridge, E. A. Melvin

IN the fall of 1953, The Consolidated Mining and Smelting Co. of Canada Ltd. put into operation a completely new and modern plant for sintering the rather complex assortment of materials which comprise the feed to the Lead Smelter at Trail, British Columbia. This Lead Smelter is one section of an integrated metallurgical plant producing lead, zinc, silver, gold, cadmium and other metals. Since most of the incoming lead concentrate contains appreci- able zinc values, and most of the zinc concentrate similarly contains appreciable lead values, the cross-routing of residues or tails from the respective lead and zinc plants offers obvious advantages in recovery of metals, and has been practiced for many years. A disparity has existed, however, between the output of zinc plant residue and the capacity of the Lead Smelter to treat it, with the result that over the years a stock-pile of residue had been accumulating, and by the end of World War II had reached the formidable total of half a million tons. To treat this stock-pile, in addition to all current zinc plant residues and, of course, the regular quota of lead concentrates, became a prime objective of the Lead Smelter following World War 11. As zinc plant residue plays an important part in the operations to be discussed in this paper, some consideration of its

Jan 1, 1958

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di'rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956

By C. K. Leith

OTHERS here are far better qualified than I to discuss some of the specific proposals for government regulation of the oil industry. I shall make no attempt to carry oil to Oklahoma. The question of public control, however, is inherent in other branches of the mineral industry in varying degrees, and my comments will be directed mainly toward some of the trends affecting the mineral industry as a whole, as a background for your more specific consideration of oil legislation. A proud American tradition has been the insistence on freedom of competition, on equality of economic opportunity, on a policy of laissez faire. Nowhere has this principle been given wider application than in the mineral industry. The mineral field has been open to all comers, and the job of mineral exploitation has naturally attracted daring and independent spirits. The laws governing conditions of discovery and development, as well as the anti- trust laws, have been devised to foster the spirit of private initiative. The result has been the building of a mineral industry on a scale never before approximated anywhere in the world. The impetus thus gained, the methods, the technique, the financial resources, have been projected be- yond our boundaries and have made the American mineral industry the purveyor to the world for many essential commodities and first in the exploitation of the world's minerals. Our habits of individual self-reliance and success are deeply ingrained, and there is hardly an individual in the entire mineral field who does not instinctively recoil fro111 the extension of collective control, whether public or private.

Jan 1, 1932

By Hugh Roberts

During 1916 and 1917, the E. J. Longyear Co. of Minneapolis, Minn., carried out a campaign of exploration for nickel-copper ore in the Sudbury District of Ontario. The work was initiated by W. E. Smith, a resident of Sudbury, who called the attention of W. J. Mead, Chief geologist. The E. J. Longyear Co., to the fact that explorable lands in the Sudbury District were still available. Five diamond drills were employed, and holes were drilled in the townships of Levack, Trill, Denison, Blezard; Garson, Falconbridge and MacLennan. The general map of the District, Fig. 1, shows the distribution of the lands chosen. As a result of this exploration, a large body of nickel and copper ore has been found in the western part of the Township of Falconbridge. This property lies in the eastern part of the Sudbury District, east of the Garson mine.

Jan 2, 1918

By S. Warren Hobbs

The section of the Northwestern United States that includes the northern Rocky Mountains and adjacent areas to the west and east is one of large mineral production and important mineral potential. The metallic ore deposits vary widely in age and type and their geologic settings are similarly diverse. A brief resume of the region's physiographic characteristics and geology sets the framework for the selected ore districts that are described in following papers and makes it possible to place these ore deposits in their proper reference to space and time.

Jan 1, 1968

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of vary-ing thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition.

Jan 1, 1939

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By John B. Baker, Bernard B. Betty, H. F. Moore

Fox several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.1,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. SPECIMENS The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.-The Bridgman method of casting single-crystal speci¬mens was used.3 The specimens were cast to the shape and size shown in Fig. I (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By Arthur Phillips

The progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yielding supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with particular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weertsl recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150" and 225' C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler and Sachs,2 who indicated a parameter value, for the same alloy annealed for 24 hr. at 200° C., some 0.0008Å. larger than that of pure aluminum. Stenzel and Weerts attributed the abnormal lattice dimension to the effect of strain induced by the precipitation of CuA12. Weerts3 later

Jan 1, 1934

By W. C. Hardy, B. W. McArthur

The purpose of this work is to show application of laboratory data in calculating solution gas-drive performance of the Cisco K-I reservoir. Included herein is a diagram showing the graphical relationship between six variables common to all solution gas-drive mechanisms. With an iterative process one may assume existence of any of these six variables at a particular pressure and calculate the production performance likely to occur in a reservoir produced by solution gas drive. Four unique pressure values are described at which the material balance equation alone is sufficient to predict the cumulative volumes of gas produced. Information derived from these pressure points establishes a criterion for determining compatibility of the pressure-volume-temperature (PVT) analysis of the produced crude with the gas production history. Two averaging procedures are used to arrive at a relative permeability-saturation relationship which describes the field-wide performance. INTRODUCTION The Cisco K-1 reservoir is a lenticular-type sand structure lying at approximately 6,300-ft subsurface. It is located in the H. and T. C. Railroad Co. Block 97, SW 1/4 S 392 and NW 1/4 S 385, Scurry County, Tex. Correlation of data from logs indicated that the Cisco K-1 reservoir occupied approximately 3,218 acre-ft of space with a closure of from 15 to 20 ft. Analysis of the production data indicates that the initial formation pressure and temperature were 2,450 psig and 121°F, respectively. The bubble point occurred at 1,715 psig after production of 12,256 STB oil and 11,520 Mcf gas. Only traces of water have been produced since initiation of production. Successive material balance calculations from June, 1952, to June, 1957, showed that no initial gas cap or water influx has contributed to production of oil and that the Cisco K-1 reservoir originally contained approximately 1.44 X 10" STB of oil. THEORY Methods for calculating solution gas-drive perform-

By R. G. Treuting, R. M. Brick

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By R. M. Brick, R. G. Treuting

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By Paul R. Bluekamp

The Mather Mine property is composed of a 5.2 sq km (2 sq mile) area within the Cities of Ishpeming and Negaunee which are located in the Upper Peninsula of Michigan. Production in this mine started in 1943; it ran continuously until its closing in 1979, having produced slightly over 55 million tons of iron ore. This mine was a joint venture between several steel companies and The Cleveland- Cliffs Iron Company (CCI), with CCI being the fee holder and operator. For the first 17 years of operation, the ore was shipped in its natural state directly from the mine to the steel mill. By 1960, iron ore pellets were on the market and they proved so superior to the natural soft Mather ore that the latter became difficult to sell except for the coarser portions. It was decided to develop a pelletizing process for the Mather ore, and this was accomplished by 1965 when the first Mather pellets were produced. From this date, all but the coarse fraction of the Mather ore was shipped as pellets. The geological setting is that of a large east-west trending synclinorium which plunges to the west. The lowest member of this trough-like structure is, for the most part, a quartzite-like graywacke, the upper 20 m of which grades into a softer, fine grained slate. Lying conformably on this graywacke footwall member is an iron- formation member which is over 1,300 m in thickness. This iron-formation is cow posed of thin alternate bands of iron oxides and chert and is intruded by a number of diorite sills - some up to 122 rn (400 ft) in thickness. The north limb of this synclinorium dips at approximately 45' and bottoms out at about 1,000 m from surface in the central part of the mine. There are two sets of faults, many of which are intruded by diorite dikes, which trend east-west and southeast-northwest. Displacements are varied, reaching a maximum displacement of 243 m (800 ft). The ore is found lying directly on the slatey footwall and its position is largely controlled by the faults and dikes, with the bulk of the ore being on the upper side of these structures. The ore is composed of soft earthy hematite and martite with vertical thicknesses up to 122 m (400 ft) although the average thickness would be closer to 46 m (150 ft). The ore averaged 60% iron and 7% silica on a dried analysis. The Mather Mine is located on the north limb of the syncline and was worked from two shafts, the deepest of which. was 1,09 7 m. These two shafts are about 2 km apart and serviced a total of 8 working levels between them during the life of the mine. The level spacing was about 61 m (200 ft). The main haulageways were driven parallel to the ore/footwall contact in the hard cow petent graywacke wherever possible. On the lower levels, deeper into the footwall, naked development was common. This material graded into roof bolting ground towards the upper stratigraphic portion. As drifting progressed further into the upper stratigraphic portion of the footwall, progressively stronger steel sets had to be used. From the main haulageway, cross-cuts were turned into the orebody on 61 m (200 ft) centers and extended as far as needed to recover the ore available to that particular cross-cut. The main haulageways and cross-cuts were driven 3 m (10 ft) high, 3 m (10 ft) wide at the top and 4.6 m (15 ft) wide at the bottom. This configuration would accomodate a set composed of a 2.7 m (9 ft) cap on top of two 2.7 m (9 ft) legs angled out at 18'. A sill plate was used under each leg to prevent its sinking into the ore below. The type of steel used was dependent on the expected weight to be experienced. Sets were placed on 1.63 m (5 ft 4 in.) centers; however, in extremely heavy areas, it was sometimes necessary to install sets on 0.8 m (2 ft 8 in.) centers. On the top two levels (5th and 6th), the ore was considerably hard-er and was mined by sub-level stoping and long hole drilling. Very light steel sets were used in the main haulageways and cross-cuts and timber was used in the production drifts. Some con- crete production drifts were installed on 6th level, but proved to be uneconomical. However, as mining reached greater depths, the ore became softer and more massive, reaching its maximum vertical heights on 11th and 12th levels. On levels 7 through 10, yielding steel sets were used extensively in the slusher drifts. While they were satisfactory on 7th and 8th levels, their success diminished with depth and they were

Jan 1, 1981

By John E. Murphy, Ernest L. Ohle

Hematite-magnetite ore bodies at Iron Mountain, Missouri, have produced nearly 9 million tons of iron ore concentrates since 1844. The ore minerals occur principally as open-space filling in fractured and brecciated andesite porphyry with very minor replacement of the wall rocks. The enclosing rocks are Precambrian in age and consist of a series of dacite, rhyolite, and andesite flows aggregating about 2000 feet in thickness. All of the ore is in andesite and the mineralization is Precambrian in age. The shape of the ore bodies, the breccia character of the ore, and the gangue mineralogy are believed to be unique. One of the two main ore bodies is crudely dome-shaped with a tendency for development of concentric mineralized shells; the other is an elongated lense in plan but hook-shaped in cross section. Both have strong linear elements striking northeast, east-west, or northwest. Various modes of origin for the structures and for the tension breccias have been suggested, but none is completely satisfactory. Hematite is the main ore mineral; magnetite is subordinate. Important gangue minerals are andradite, quartz, calcite, actinolite, apatite, epidote, and chlorite. Although some evidence favors injection of an iron-rich melt, other evidence suggests ore formation by a high temperature, water-rich solution.

Jan 1, 1968