Search Documents

By Arthur L. Hawthorne

10.1-1. Relative Position of Maintenance as Compared to the Overall Mining Costs. The basic issue regarding the importance of maintenance in the modern mining industry must be faced squarely by the top manage- ment of each company before any real progress can be made in organizing a maintenance program for optimum effectiveness. Just a few decades ago the maintenance at coal mines consisted primarily of a blacksmith for sharpening picks and shoeing mules; as a result, probably less than 5%of the total mining cost went to maintenance and some 80% was operating expenses (operating labor). With each succeeding advance in equipment design towards larger, more complex, and more productive units, the pendu- lum swings the other way. As an example, haulage trucks have progressed through various stages in the past 20 years from 15-ton units to a 240-ton truck now in the "shakedown" or experimental stage. The following com- parison between 15-ton, 50-ton, and 100-ton haulage trucks clearly illus- trates this changing cost pattern in terms of percent of overall costs for running each size unit. [Maintenance 24% 44 % 51 % Operating labor 59 % 33 % 16% Operating supplies (fuel oil) 4 %. 4% 3% Labor burden and vac. pay 6 % 4% 3% Depreciation Total] From the preceding figures it is interesting to note that, as a rule, operat- ing costs go down as the equipment gets larger and the maintenance costs increase with the larger units. This same trend in cost variation applies to nearly all mechanical equipment used in surface mining from the large

Jan 1, 1968

By Ernest Burchard

A RECONNAISSANCE Of the manganese-and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines under instructions of the Secretary of the. Interior, in the Spring of 1918. The object of the study was to obtain authentic information for the use of the United States Government as to the location, character, quantity, and availability of the manganese and chrome-ore deposits in Cuba. Accordingly, the work comprised the examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. While it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Manganese ore is found in Cuba in Oriente, Santa Clara, and Pinar del Rio Provinces, but in Oriente Province only does it occur in large commercial quantities. There, the deposits are in three areas: one north of Santiago de Cuba, one south of Bayamo and Baire, and one on the Caribbean coast between Torquino Peak and Portillo. In Santa Clara Province, a little ore has been found near the Caribbean coast west of Trinidad; and in Pinar del Rio Province, manganiferous material occurs north of the city of Pinar del Rio and farther west near Mendoza. The manganese ores of Cuba occur, principally, in sedimentary rocks, such as limestone, sandstone, and shale, that are in places metamorphosed, and. in beds that originally may have been water-laid tuff

Jan 3, 1919

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By F. P. Haver, M. M. Wong

The Federal Bureau of Mines has developed a leach= electrolysis method for recovering lead from galena (PbS). Flotation concentrate is leached with ferric chloride (FeCl3) solution to obtain lead chloride (PbC12) and elemental sulfur, PbS + 2FeC13 -+ PbC12 + 2FeC12 + Sº. Over 99% of the P~S in the condentrate is converted to PbC12. The leach solution, composed of brine (NaC1) and FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. Very pure PbC12 (>99.9%).is crystallized from the leach filtrate on cool- ing and is subsequently electrolyzed in a fused-salt bath to obtain molten lead metal (>99.9% Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride, and other values, such as Ag, Cu, Zn, and Sº, are recovered by additional treatments of the leach solution and leach residue. This paper discusses results and conditions of the leaching and electrolysis operations.

Jan 1, 1976

By R. K. Datta

Eluropium -activated yttrium vanadate, excited by short- and long-wavelength ultraviolet radiations, shows enzission lines near 6100A, the principal ones correspondirzg to transitions of EU+3 ions from 5Do to the F2 energy level. The ~neclmlallistns of absorption and etnissiorz of this phosphor have been empirically studied. The absorption is caused by two separate processes in the matrix. The phosphor YVO4:Eu and tlie matrix YVO, haue essentially the same resectance spectra in the region 2500 to 4000if. There are two broat ah~o?~ption bands: natnely, around 2600 and 3600A regions. Whet? compared with the reflectance spectra of the constituent oxides, namely, Y2O3, V205, Eu2 03, the absorption bands of the tnatvix and the phosphor in the short- and long-wavelength ultraviolet regions can be interpreted as due to charge-transfer processes involving i) Y-O and ii) 17-0, respecti~~ely. The excitation spectrum' of the phosphor has two broad bands with peaks at about 2600 and 3600A regions. U can be postulated that enevgy absorbed under short- crud long-wavelength ultraziolet excitatzon, respectzcely, by Y-0 and V-O parts of the niatrix is transferred by radcatio~zless process to EU+3 ions. Thzs postulate can empirically be proved on the basis of the spectra of the systems (YVO4,-YPO4,):Eu. PO? ~ons do not have' any appreciable absorption in the short or long uv regions. When P0't3 ions are substitlited for v0i3 ions in YVO,:Eu phosphors, the absorption and excitation in the lo~zg uv region are gradually reduced. Ailoreover, the £«+3 emission under 3650A excitation is decreased zuitlz increase in PO^ content, lt~lzereas the emission under 253711 excitation remains esserztially constant with as IILUCIL as 60 mole pct of YPO, in YVO,:En. EUROPIUM-activated yttrium vanadate (YV04:Eu) is a well-known phosptor.'-3 When excited by cathode rays, 2537, or 3650A radiations, YV04:Eu emits typical narrow-band spectrum of EU'3 fluorescence in the region of 5900 to 7100A, a very strong maximum occurring at about 6190A. This emission is considered to be due to 5Do — 7F2 transition of excite: EU*3 in 4f state. Moreover, the emission under 3650A excitation increases with temperature markedly. Because of these properties, YV04:Eu phosphor finds wide application in industries, namely, in color television tube, laser, and high-pressure mercury-vapor lamps. It is the purpose of this paper 1) to present the empirical study of the mechanism of absorption and excitation of YV04:Eu phosphor by ultraviolet radiation, and 2) to offer an explanation for the process of emission. It should be mentioned that a theoretical discussion on the mechanism of absorption in terms of the crystal or ligand field theory is beyond the scope of this paper. Empirical studies presented here are based primarily on spectroscopic and crystal-chemical investigations. EXPERIMENTAL i) Preparation of Materials. The synthesis of vanadate phosphorinvolves preparation of (Yi-.tEuj^Oj, blending the mixed oxide with an oxidic compound of vanadium, such as V205 or NH4V03, and firing the mixture at about 1000°C for several hours when YVO4:Eu forms as a primary phase. (Y1-xEux)203 compositions are prepared by coprecipitation of oxalates, and igniting them at about 1000°C. The vanadium compound is added in excess of the stoichiometric proportion for fluxing purposes. The charge is cooled, ground, and the excess of vanadium is removed by a hot wash (-80°C) of alkali or ammonia. Y(VP)04:Eu samples are prepared by mixing (Yi-xEux)203 with stoichio-metric proportions of (NH4)2HP04 and the vanadium compound. The mixtures are prefired at 700" to 800°C for 1 or 2 hr, then ground and refired at 1150°C. The firings of the phosphors are done in silica crucibles, and the homogeneity of the final products checked by X-ray diffraction analysis. ii) Spectroscopic Measurements. Diffuse reflectance sqectra of the samples within the range 2500 to 7000A are obtained by using CaF2 as standard in Cary Recording Spectrophotometer, Model No. 14. The emission spectra from phosphor plaques, excited under different ultraviolet sources, are obtained by a direct-recording spectroradiometer4 adapted with a grating monochromator with nearly constant dispersion. Maximym sensitivity in the spectral region from 2500 to 7000A is obtained with a quartz-windowed, S-20 response p$otomultiplier. The total' band pass is kept about 30A. The spectra are calibrated against the light from a standard tungsten filament lamp reflected from a magnesium-oxide plaque. Brightness data given throughout this report $re measured from the height of the main peak (6190A) of the emission spectra. The excitation spectra are measured using sodium salicy-late as standard. RESULTS AND DISCUSSION The diffuse reflectance spectra of both pure and activated YV04, along with their constituent components, are shown in Fig. 1. YVO4 shows two broad absorption bands, namely, around 2500 and 3600A, respectively. Since there is little difference between the reflectance spectraoof YVO4 and YVO,:Eu in the uv region (2500 to 4000A), it can be postulated that excitation of the phosphor is mainly due to absorption by the matrix, i.e., YVO4. The question, now, is whether the matrix (Yv04) is excited as a whole, or different components are responsible for the two absorption bands. The characteristic absorption spectra of molecular ions involving transition metal ions, both in aqueous solutions and in crystals, are due to electronic transi-

Jan 1, 1968

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.' This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

BIRINGUCCIO was born in Siena in 1480, the son of Paolo and Lucrezia di Bartolommeo Biringuccio.* He was baptized on October 20 of that year with the given names Vannoccio Vincenzio Austino Luca. His father appears to have been an architect, for in 1504 he was paid 600 scudi for his work on the walls of the Communal Palace and at the same time he was superintendent of streets for the city. The course of Biringuccio's life followed closely the checkered fortunes of the Petrucci family of Siena. A warm supporter of Pandolfo Petrucci, Biringuccio did not falter in his allegiance to the family and their party during his lifetime. It was probably to the protection and patronage of this lord that he was indebted for the opportunity to travel widely through Italy and into Germany during his early years and so to lay the foundation for the extensive knowledge of the subjects he was to describe in the Pirotechnia. In 1507, as he himself indicates (p. 48), he was 'in Friuli and. Carnia in northern Italy after having traveled in Germany,, and he also visited the, brass, works in Milan. After returning to Siena; he was sent by Pandolfo to direct the iron mines in near-by Boccheggiano. When Pandolfo died in 1512 (in which year Biringuccio's s father also died), Biringuccio continued to support the Petrucci family in the person of Pandolfo's son, Borghese, who succeeded, to the rule. Under his patronage, Biringuccio was appointed to a post in: the Armoury of the Siena Commune in 1513. In ISIS a popular uprising forced Borghese and his followers, including Biringuccio, to flee from Siena. Biringuccio and the goldsmith Francesco Castori, head of the mint, were accused of having debased the coinage alloy with the knowledge and consent of Borghese. When he failed to appear in 1516 to answer these charges-which may well have been invented by the opposing political faction-Biringuccio was declared a rebel and was exiled as a traitor to the Republic. He then traveled about Italy, was in Rome and Naples, and visited Sicily in 1517.

Jan 1, 1942

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By Alfred Beasley

LEAD-REFINING practice at the. Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill-has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1.

Jan 1, 1930

Annual Meeting,Wallace, Idaho, Nov. 15-16, 1913. The third annual meeting, which was also the eighth consecutive meeting and the second to be held in the Coeur d'Alène district, was held in Wallace, Idaho, Nov. 15-16, 1913, with side trips to Kellogg-Wardner, Larson, and Mullan, where several mills were visited. The meeting was held jointly with the Montana Section, about 50 members and guests being present. Headquarters were in the Samuels Hotel, sessions being held in the public library. The arrangements and program were in the hands of the following local committee: George W. Roddewig, W. Earl Greenough, H. M. Childs. At 2.30 p.m., Nov. 15, the first session was called to order by Prof. F. A. Thomson, member of the Executive Committee, adjournment being taken to the Mine Rescue car, where Mr. Anderson and his assistant entertained the visitors for nearly two hours by demonstrations of mine-rescue and, first-aid practice, after which the party visited the Hercules mill, mention of which was made in the report of last year when the Section visited the plant. There are, however, several important alterations and additions to the flow-sheet to be noted, such as substitution of Chilean and Hardinge mills for the Huntington mills in the regrinding department; rearrangement of the tables and slimers, with a noticeable addition of the later models of the Franz machines, and the installation of the Wyman flotation process, which has been tried out, or is being tested, with more than ordinary success, on the middlings in several of the mills of the district, the Green Hill Cleveland mill being provided with a 100-ton unit, partly described below

Jan 12, 1913

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

Aamot, Olav Crone, Chem. Engr., Elektrokemisk Raadhusgt..23, Oslo. Norway. '29 Abadilla, Quirico A., Dir., Bureau of Mines Manila, P. I. '3S Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L.. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '2S Abel, Walter D., Div. of Corporations Los Angeles, Calif. '32 Abele, Louis T., U. S. Corps of Engrs 7211 Glen Oak Ave., Baltimore. Md. '31 Abel], Leo M., Research Met., Mount Morgan Ltd Mount Morgan, Queens.. Australia. '31 Abenius, Hakan V c/o Falu Gruva, Falun, Sweden. '37 Abernathy, G. E., Geol., Kansas State Geol. Survey Pittsburg, Kan. 3S Aborn. Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abrams, Charles Jackson 1624 17th St., Denver, Colo. '3 t. Abstein. Henry T., Engr. & Mgr., Profile-Tamarack Mines CoYellow Pine, Idaho. '27 Acker, E. O'C., Met L28 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Assoc. Prof. of Met., Purdue Univ Lafayette, Ind. '35 Ackerman, E. Dumont, Sub-Surface Geol., Temblador Camp, Standard Oil Co. of Venezuela, Caripito, Venezuela. '3S Ackerman, George F.,. Div. Foreman. The Fresnillo Co Fresnillo, Zac., Mexico. '36 Adami, A. F., V.P. & Prof. of Min. Engrg., Montana School of Mines Butte, Mont. '19 Adami, Charles J., Min. Engr 99 S. Downing St., Denver. Colo. '12 Adams, Army, Cons. Engr 714 W. Main St., Grass Valley, Calif. .'37 Adams, Clyde B.. Geol.. Socony-Vacuum Oil Co., Inc 26 Broadway, New York, N. Y. '39 Adams, Ernest C., 6th Engrs Fort MacIntosh, Laredo, Tex. '35 Adams, F. J., Gen'l Agent, Gulf Production & Pipe Line Cos Fort Worth, 'lox. '29 Adams, F. S., Supt., Power Dept., Anaconda Copper Min. CoAnaconda, Mont. '37 ADAMS. FRANK DAWSON, Hon. Mbr., 1913; Logan Prof. of Geology and Dean, Faculty of Applied Science. McGill Univ., Montreal, Que., Canada. '13 Adams, Gale L., Supervisor, Process & Dev. Lab., General Pet. Corp. of California, Higgins Bldg., Los Angeles, Calif. '18

Jan 1, 1939

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.&apos; It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

By J. Leja, A. Pomianowski

This paper deals with equimolar solutions of xanthate and alkyl trimethyl ammonium bromide adsorption on copper, nickel and sphalerite powders. After an exposition of the experimental methods used and the results obtained, a thorough discussion leads to the conclusion that some molecular association between xanthates and CnTAB&apos;s does take place in the bulk of the solution as well as at the air/liquid interface. A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 to 400 mµ) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed, the half life of which was established as 29±3 days at 22°C and pH ~ 6. In mixed solutions of longer xanthate homologues (e.g. hexyl and nonyl) and equimolar CnTAB, colloidal precipitates are gradually formed which contain primarily the corresponding xanthate molecules. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 to 10"3 M solutions of KEtX alone and in equimolar mixtures of KEtX and CI2TAB. Presence of C12TAB caused a two to three fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and nickel powders (and in their rates of abstraction) but had no effect on the abstraction of xanthate by unactivated sphalerite (equivalent to less than a monolayer). The adsorption of C12TAB itself from the mixed solutions was very low, at most one monolayer only, and was not influenced by the nature of the solid powder used. A change in the rates of abstraction, observed with copper powder, was interpreted as a completion of a multilayer coating (completely enveloping the grains of powder) following which the rate of reaction between solution and substrate becomes controlled by diffusion through this coating. Work of Buckenham and Schulmanl on molecular associations between different collectors has shown unusual synergistic effects in flotation of individual minerals using mixtures of xanthates and alkyl trimethyl ammonium bromides. The objectives of the present work were: 1) to determine whether these molecular associations between the two types of collectors (indicated by strong surface tension lowering in Buckenham and Schulman&apos;s work) take place at the air/liquid interface only or in the bulk of solution as well 2) to establish whether different solids adsorb any species from the mixture of these amphipatic molecules preferentially or as molecular complexes 3) to establish whether there are any differences in the kinetics of adsorption. Metallic copper and sphalerite powder were chosen as adsorbents since they represent two extremes since copper readily adsorbs multilayers of xanthate (and is easily floated with ethyl xanthate) while unactivated sphalerite does not appreciably adsorb xanthate but is known to be readily floated by the amine type collectors. Metallic nickel was included because the infrared spectroscopic work2 on xanthate

Jan 1, 1964

By H. E. Cline, D. F. Stein

A fine lamellar structure with interlamellar spacings ranging from 0.I to 3.7 was Woduced by high-speed directional solidification and used to study the interaction of dislocations with an array of bimetallic bound-am.es. The tensile flow properties were measured at elevated temperatures and the results interpreted in terms of an image force model. As the width of the plates decreases the strength increases according to a Hall-Petch relation, suggesting pile -ups. Considerable strengthening was also observed at elevated temperatures. In recent years composites containing a strong but brittle phase and a ductile but weak phase have been studied extensively in the search for a high-strength material with adequate ductility.&apos; However, the strength of these composites has been limited to a volumetric average of the strengths of the component phases. In this paper we will show that a composite made by directional solidification of a Cu-Ag eutectic has strength properties that substantially exceed the strength of either of the metals in the composite, and an explanation for this increased strength will be presented. The Cu-Ag eutectic is a near ideal material to study for several reasons. The eutectic structure is made up of alternate plates of silver-rich and copper-rich phases with the same crystal structure.2&apos;3 In addition, the mechanical and elastic properties of silver4 and copper5 are known over a wide range of temperatures and the eutectic microstructure is stable to nearly the melting point.6&apos;7 Therefore, the properties of the eu-tectic are readily comparable to various theories involving the mechanical properties of copper and silver. The experiments consisted of producing directionally solidified Ag-Cu eutectic material, determining the structure and performing tensile tests at different temperatures and strain rates. EXPERIMENTAL A) Solidification and structure. A cylindrical ingot 2.2 cm in diam and 15 cm long was prepared from 99.999 pct pure materials and cast in argon. The ingot was placed in an alumina crucible and was direc-tionally solidified at 7 x 10"4 cm per sec in a Bridg-man apparatus in argon. Metallographic examination at both ends and along the length of the ingot showed a uniform structure that consisted of fine alternate plates of silver- and copper-rich phases. The plates were aligned parallel to the growth direction, as shown in the longitudinal section, Fig. 1, and were in small randomly oriented domains of parallel plates as viewed in a transverse section, Fig. 2. Four smaller ingots 0.175 in. in diam were solidified at speeds of 2Xlo-&apos;, 4.4 xlo-&apos;, 4.4 x 10-3, and4.4x10-4 cm per sec to produce a range of lamellar spacings. Replica electron micrographs were taken to resolve the individual plates as shown in Fig. 3. The copper-and silver-rich plates in the larger ingot were about

Jan 1, 1970

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE large difference in the X-ray scattering factors for molybdenum and manganese makes the o- phase in the Mn-Mo system an interesting one to study with respect to ordering of the atoms. Such a study has been carried out using data obtained from a powder sample, and the resulting evidence for ordering in this compound is presented here. It is not possible, of course, to obtain all the details of structure for a u phase from powder data only. Most difficult of all would be the determination of precise atomic parameters. There is reason to believe, however, that the atomic parameters do not vary greatly in the different s&apos;S and that the precise values obtained from one s structure would then allow decisions as to the ordering of atoms to be made when there is a large difference in scattering factors. In particular, the powder intensities for Mn-Mo s are for the most part in good agreement with those observed for Co-Cr, for which single crystal studies have been made by the authors.&apos; There are a few marked discrepancies in the intensity comparison of the two s&apos;s, and these cannot be removed by adjustment of the parameters. They are interpreted as resulting from a more pronounced effect of ordering of the atoms. Accordingly, the parameters of Co-Cr s&apos; have been used for the calculations of the Mn-Mo intensities. For Co-Cr, the space group is D4h14-P4/mnm with atoms in the following positions: 1—2 in (b); 11—4 in (f), with x=0.1031; 111—8 in (i), with x= 0.3713 and y=0.0370; IV—8 in (i), with x=0.5662 and y=0.2396; and V—8 in (j), with x=0.3160Y and y — -0.250. The unit cell is tetragonal, with an==9.10A and cn=4.74A for the Mn-Mo u phase studied here.

Jan 1, 1955

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination &apos; of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969